A comprehensive approach to the analysis of contrast enhanced cardiac MR images

Current magnetic resonance imaging (MRI) technology allows the determination of patient-individual coronary tree structure, detection of infarctions, and assessment of myocardial perfusion. Joint inspection of these three aspects yields valuable information for therapy planning, e.g., through classification of myocardium into healthy tissue, regions showing a reversible hypoperfusion, and infarction with additional information on the corresponding supplying artery. Standard imaging protocols normally provide image data with different orientations, resolutions and coverages for each of the three aspects, which makes a direct comparison of analysis results difficult. The purpose of this work is to develop methods for the alignment and combined analysis of these images. The proposed approach is applied to 21 datasets of healthy and diseased patients from the clinical routine. The evaluation shows that, despite limitations due to typical MRI artifacts, combined inspection is feasible and can yield clinically useful information.     

Sensitivity to signal quantization of 43 Gb/s and 107 Gb/s optical 16-QAM OFDM transmission with coherent detection

The sensitivity of optical orthogonal-frequency division multiplexing (OFDM) transmission to the finite resolutions of the digital-to-analog (DAC) and analog-to-digital converters (ADC) has been analyzed using numerical simulations. We show that for back-to-back configuration the requirements regarding the number of quantization bits for the DACs are similar to the ones of the ADCs. After transmission over metro and long-haul distances a higher resolution of the DAC/ADC is required compared to back-to-back configuration. We show that after transmission it is sufficient to enhance either the ADC resolution or the DAC resolution by 1 bit.     

Removal of spurious coherence in MEG source-space coherence analysis

Source-space coherence analysis has become a popular method to estimate functional connectivity based on MEG/EEG. Source-space analysis involves solving the inverse problem, estimating the time courses of specific brain regions, and then examining the coherence between activities at different brain regions. However, source-space coherence analysis can be confounded by spurious coherence caused due to the leakage properties of the inverse algorithm employed. Such spurious coherence is typically manifested as an artifactual large peak around the seed voxel, called seed blur, in the resulting coherence images. This seed blur often obscures important details of brain interactions. This paper proposes the use of the imaginary part of the coherence to remove the spurious coherence caused by the leakage of an imaging algorithm. We present a theoretical analysis that explains how the use of imaginary part can remove this spurious coherence. We then present results from both computer simulations and experiments using resting-state MEG data which demonstrate the validity of our analysis.     

Analysis of temperature-dependent optical gain in GaN-InGaN quantum-well structures

The temperature dependent spectral gain in InGaN-GaN multiple quantum-well structures with 10% In content is investigated. Mode gain is measured in a temperature range between 239 K and 312 K using the Hakki-Paoli technique and compared to simulations. The simulation accounts for temperature-dependent polarization dephasing, and hence homogeneous broadening, in a rigorous fashion, without any fit parameter. It is found that the evolution of the gain spectrum with temperature at different drive currents can be modeled using a temperature-independent single value for inhomogeneous broadening. The resulting compositional fluctuations are compared to structural measurements.     

Adhesion and Mechanical Properties of PNIPAM Microgel Films and Their Potential Use as Switchable Cell Culture Substrates

Thermoresponsive poly(N‐isopropylacrylamide) (PNIPAM) microgel films are shown to allow controlled detachment of adsorbed cells via temperature stimuli. Cell response occurs on the timescale of several minutes, is reversible, and allows for harvesting of cells in a mild fashion. The fact that microgels are attached non‐covalently allows using them on a broad variety of (charged) surfaces and is a major advantage as compared to approaches relying on covalent attachment of active films. In the following, the microgels’ physico‐chemical parameters in the adsorbed state and their changes upon temperature variation are studied in order to gain a deeper understanding of the involved phenomena. By means of atomic force microscopy (AFM), the water content, mechanical properties, and adhesion forces of the microgel films are studied as a function of temperature. The analysis shows that these properties change drastically when crossing the critical temperature of the polymer film, which is the basis of the fast cell response upon temperature changes. Furthermore, nanoscale mechanical analysis shows that the films posses a nanoscopic gradient in mechanical properties.     

CdTe/CdS thin film solar cells grown in substrate configuration

The ability to grow efficient CdTe/CdS solar cells in substrate configuration would not only allow for the use of non‐transparent and flexible substrates but also enable a better control of junction formation. Yet, the problems of barrier formation at the back contact as well as the formation of a p–n junction with reduced recombination losses have to be solved. In this work, CdTe/CdS solar cells in substrate configuration were developed, and the results on different combinations of back contact materials are presented. The Cu content in the electrical back contact was found to be a crucial parameter for the optimal CdCl₂‐treatment procedure. For Cu‐free cells, two activation treatments were applied, whereas Cu‐containing cells were only treated once after the CdTe deposition. A recrystallization behavior of the CdTe layer upon its activation similar to superstrate configuration was found; however, no CdTe–CdS intermixing could be observed when the layers were treated consecutively. Remarkably high V_OC and fill factor of 768 mV and 68.6%, respectively, were achieved using a combination of MoO₃, Te, and Cu as back contact buffer layer resulting in 11.3% conversion efficiency. With a Cu‐free MoO₃/Te buffer material, a V_OC of 733 mV, a fill factor of 62.3%, and an efficiency of 10.0% were obtained. Copyright © 2012 John Wiley & Sons, Ltd.     

A new normalized relatively stable lattice structure

This paper proposes a new lattice filter structure that has the following properties. When the filter is linear time invariant (LTI), it is equivalent to the celebrated Gray-Markel lattice. When the lattice parameters vary with time, it sustains arbitrary rates of time variations without sacrificing a prescribed degree of stability, provided that the lattice coefficients are magnitude bounded in a region where all LTI lattices have the same degree of stability. We also show that the resulting LTV lattice obeys an energy contraction condition. This structure thus generalizes the normalized Gray-Markel lattice, which has similar properties but only with respect to stability as opposed to relative stability     

Microwave radiometry for cement kiln temperature measurements.

The maximum temperature inside a cement kiln is a critical operating parameter, but is often difficult or impossible to measure. We present here the first data that show a correlation between cement kiln temperature measured using a microwave radiometer and product chemistry over an eight-hour period. The microwave radiometer senses radiation in the 12-13 GHz range and has been described previously [Stephan and Pearce (2002), JMPEE 37: 112-124].     

Correcting for contact geometry in Seebeck coefficient measurements of thin film devices

Driven by promising recent results, there has been a revived interest in the thermoelectric properties of organic (semi)conductors. Concomitantly, there is a need to probe the Seebeck coefficient S of modestly conducting materials in thin film geometry. Here we show that geometries that seem desirable from a signal-to-noise perspective may induce systematic errors in the measured value of S, S_m, by a factor 3 or more. The enhancement of S_m by the device geometry is related to competing conduction paths outside the region between the electrodes. We derive a universal scaling curve that allows correcting for this and show that structuring the semiconductor is not needed for the optimal electrode configuration, being a set of narrow, parallel strips.     

Core–Shell Nanoparticle Interface and Wetting Properties

Latex colloids are among the most promising materials for broad thin film applications due to their facile surface functionalization. Yet, the effect of these colloids on chemical film and wetting properties cannot be easily evaluated. At the nanoscale, core–shell particles can deform and coalesce during thermal annealing, yielding fine‐tuned physical properties. Two different core–shell systems (soft and rigid) with identical shells but with chemically different core polymers and core sizes are investigated. The core–shell nanoparticles (NPs) are probed during thermal annealing in order to investigate their behavior as a function of nanostructure size and rigidity. X‐ray scattering allows to follow the re‐arrangement of the NPs and the structural evolution in situ during annealing. Evaluation by real‐space imaging techniques reveals a disappearance of the structural integrity and a loss of NP boundaries. The possibility to fine‐tune the wettability by tuning the core–shell NPs morphology in thin films provides a facile template methodology for repellent surfaces.