Review of Mechanically Related Failures of Ceramic Capacitors and Capacitor Materials

This paper reviews the brittle fracture behavior of dielectric ceramics such as barium titanate, and describes some of the relationships between defects such as cracks and electrical degradation and failure of multilayer capacitors. Stresses arising from the ferroelectric phase transformation in these dielectric materials are shown to play a part as a driving force for crack growth. In addition, possible contributions to failure from stresses arising from thermal excursions in the capacitor are discussed. Low-voltage failures arising from a short between the electrodes in multilayer capacitors are shown to be related to the growth of cracks in the dielectric. A technique for predicting the onset of these types of failures based upon fracture mechanics techniques is described. Possible effects of the electric field itself in promoting or retarding the growth of cracks are discussed.     

Exploiting border structure in solving large sparse linear systems in bordered triangular form

An elimination strategy for solving sparse linear systems in bordered triangular form is presented. This strategy is designed to exploit certain common structural properties of the borders of such a system. It may also be interpreted as a recursive application of block elimination. The technique is numerically efficient and provides significant reductions in fill-in compared to routine Gaussian elimination. It is applicable in the iterative solution of the large systems of nonlinear equations that arise in the equation-oriented approach to process simulation and design calculations, as well as in other problems of interest to the chemical engineer.     

Fabrication and characterization of planar and channel polymer waveguides. III. Compositional distribution and solute loss in polymer thin films

For many microelectronic and optoelectronic applications, polymer thin films require the addition of small molecules. However, the thin‐film geometry and associated processing techniques will influence the final morphology and compositional distribution of the constituents. It is therefore important that these be examined directly rather than inferred from bulk measurements. As an example system, the concentration and distribution of Disperse Red 1 (DR1) molecules in poly(methyl methacrylate) thin films were examined. Ultraviolet visibility spectroscopy and dynamic secondary ion mass spectrometry indicate that the composition of the molecules decreased dramatically with thermal treatment of the film. The sublimation of the chromophore was observed to occur at temperatures well below the melting point of the small molecule and the glass transition of the pure polymer; this solute loss manifested itself in changes in the glass transition temperature of the film. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2021–2024, 2002     

Zeolite Formation in Class F Fly Ash Blended Cement Pastes

Zeolite formation in Class F fly ash blended cement pastes is under investigation. A Na–P type zeolite and Zeolite Y were synthesized from Class F fly ash and NaOH solution after 2 days of aging at room temperature and 6 days of curing at 80°C. However, no zeolites formed when KOH was used. In additional experiments, a Na–P type zeolite, Zeolite Y, and chabazite developed in cement pastes blended with Class F fly ash and NaOH solution which had been aged 2 days at room temperature and then cured 6 days at temperatures ranging from room temperature to 90°C. Seeding the pastes with natural zeolites was also investigated.     

ASPECTS OF JOINT DESIGN AND EVALUATION IN THICK-ADHEREND APPLICATIONS

Structural adhesives are gaining wide recognition by industry as they offer engineering designers greater flexibility to achieve economic and technical advantages. In the marine industry there are potential applications for adhesives in various types of construction, for example, thick steel and composite adherends, (typically 5-15 mm thick). The applications include panels and large pipes. This article is largely concerned with the use of two-part epoxy adhesives. The purpose of this article is to understand and evaluate the weaknesses of adhesives and adherends, in relation to specific applications and to use design and material selection to alleviate them. This understanding can be extended to other thick adherend applications. This article will also highlight the impact of structural epoxy adhesive technology on the design and fabrication of steel, composite, and hybrid constructions. The benefits and inherent limitations that can accrue are quantified through three case studies related to thick adherend connections.     

Prediction of DNA-binding regulatory proteins in bacteriophage T7

The high-resolution structure of several specific DNA-bindingproteins have been determined, and they display a common structuralmotif which mediates their binding to DNA. This motif consistsof two -helices connected by a sharp turn, and its amino acidsequence has several distinguishing features. A computer searchof the proteins coded by the genome of bacteriophage T7 hasbeen performed in an attempt to identify those proteins thatpotentially contain this motif. Eight proteins were found tohave regions similar to that of the motif. Of these, three arerelatively small, have no known function and are good candidatesfor being DNA-binding regulatory proteins. The methods describeduse commonly available computer programs and databases, andare therefore easy to implement.     

Strain-Induced Deformation in Magnesia–Alumina Layered Composites

Ceramic beams are induced in situ to form complex shapes at elevated temperature without the application of an external stress. This process has been demonstrated for thin alumina substrates coated with a layer of magnesia. The internal strain causing the substrates to deform at elevated temperature arises as a consequence of strain mismatch accompanying the penetration of the coating into the substrate. The magnitude of the deformation depends on the amount of coating applied, on the thickness of the substrate, on the density of the substrate, and on the temperature. During exposure of the beams to elevated temperature, the magnesia coating reacts with the alumina substrate to form the spinel phase; the resulting volume change accompanying the phase transformation is likely the predominant driving force for deformation.     

Preparation and characterization of cellulose acetate organic/inorganic hybrid films

A series of organic/inorganic hybrid (OIH) films were prepared using cellulose acetate (CA) as the organic component and tetraethyl orthosilicate (TEOS) as the inorganic component. The chemical, morphological, and mechanical properties of these films were evaluated with a variety of analytical techniques. The results of these evaluations showed that crosslinked CA OIH films were formed during the sol-gel reactions. The structure of OIH films was very sensitive to the CA/TEOS ratio and film formation conditions. All of the films with added TEOS were two phase on a molecular level, i.e., inorganic TEOS domains surrounded by a CA matrix. Under some film formation conditions the presence of TEOS, a nonsolvent for CA, led to solvent/nonsolvent phase separation on the micron scale. © 1995 John Wiley & Sons, Inc.     

Novel poly(butylene terephthalate)/poly(vinyl butyral) blends prepared by in situ polymerization of cyclic poly(butylene terephthalate) oligomers

Blends of in situ polymerized PBT from cyclic oligomers (c-PBT) and PVB were prepared with varying compositions and compared with mechanical blends of conventional PBT and PVB. The materials were characterized by a variety of techniques including DSC, DMTA, DETA, FTIR, NMR and GPC. It was found that the in situ prepared blend of c-PBT/PVB has one glass transition temperature and shows evidence of miscibility. In contrast, the conventional blend of PBT/PVB shows incompatibility after blending. The cause of miscibility in the in situ prepared PBT/PVB blends is thought to be the formation of a graft copolymer. These results show that there are unique possibilities for in situ processing by combining polymerization of cyclic polyester oligomers with blending.     

Microstructure and its relationship to deformation processes in amorphous polymer glasses

The microdeformation morphology of a number of vinyl polymers with bulky side chains (type I) and arylene polymers with flexible oxygen linkages (type II) was studied by electron microscopy. The polyarylenes crazed only near the glass transition while the polyvinyls exhibited a crazing regime that extended to liquid nitrogen temperatures. In addition significantly less plastic strain was localized in type II glass crazes relative to those in type I glasses. In compatible blends of polystyrene (PS) and 2,6-dimethyl poly(phenylene oxide) (2MPPO), ca. 30% 2MPPO was sufficient to induce a transition from type I to type II crazing behavior. Small amounts of PS suppressed the low-temperature 2MPPO β relaxation but enhanced the intermediate transition of 2MPPO at higher temperatures. Blending increased the conformational energy of the 2MPPO chain and improved interchain packing. The propensity for the polymer glass to form sharp shear bands at the expense of diffuse bands was increased by a decrease in the conformation energy of the polymer chain and an improvement in the glassy state packing.