连续工作型电子装备战备完好性预计

从战略完好性的实际内涵出发，考虑到装备实际工作中可能处于不同的工作状态，因而其战略完好性模型也应有所有同。对于处于连续工作状态的电子装备，即使工作中发生故障，只要执行下次任务前能修好，就不影响装备的战略完好性。基于此，得出了电子装备处于连续工作状态下的战略完好性预计模型，并在对应的条件下对此模型的得出进行了缜密的推理。     

ZnGa2O4纳米晶的制备和结构表征

采用喷射共沉淀法制备了ZnGa2O4 纳米晶，XRD、SEM和TEM结构分析结果表明，喷射共沉淀法制备的ZnGa2O4的纳米晶颗粒细小均匀，形状完整，与化学共沉淀法相比，粒子尺寸明显减小，小于10nm，同时ZnO杂相峰消失，分析了喷射共沉淀法的机理，并对实验结果进行了解释。     

长距离曲线顶管在杭州河坊街工程中的应用

对杭州市重点工程—杭州河坊街长距离曲线顶管进行了总结和介绍 ,可为同类工程借鉴和参考     

Improvement of RCA transistor using RTA annealing after theformation of interfacial oxide

A polysilicon emitter RCA transistor (an ultra-thin interfacial oxide layer exists between polysilicon and silicon emitter) is presented which can operate at 77 K for the first time. An ultra-thin (1.5 nm) interfacial oxide layer is grown deliberately between polysilicon and silicon emitter using RCA oxidation and excellent device stability is obtained after rapid thermal annealing (RTA) treatment in nitrogen atmosphere. The RCA transistor exhibits good electrical performance at very low temperature for an emitter area of 3 × 8 μm². The maximum toggle frequency of a 1:2 static divider is 1.2 GHz and 732 MHz at 300 K and 77 K, respectively     

Nondestructive evaluation of the characteristics of degraded materials using backward radiated ultrasound

The frequency dependency of Rayleigh surface wave is investigated indirectly by measuring the angular dependency of the backward radiation of the incident ultrasonic wave in two kinds of degraded specimens by scuffing or corrosion. Then, the frequency dependency is compared with the residual stress distribution or the corrosion-fatigue characteristics for the scuffed or corroded specimens, respectively. The width of the backward radiation profile increases with the increase of the variation in residual stress distribution for the scuffed specimens. In the corroded specimens, the profile width decreases with the increase of the effective aging layer thickness and is inversely proportional to the exponent, m, in the Paris’ law that can predict the crack size increase due to fatigue. The result observed in this study demonstrates high potential of backward radiated ultrasound as a tool for nondestructive evaluation of subsurface gradient of material degradation generated by scuffing or corrosion.     

明渠水流泥沙运动水深平均及力矩方程的理论和验证

首次提出了水流泥沙运动水深平均及其力矩方程的概念 ,并从理论上推导出这套方程组。提出水流泥沙运动力矩方程的目的有两个 ,一是在不增加空间维数的情况下可以有效地恢复水流泥沙因子沿水深分布信息 ,克服目前普遍使用的水深平均方程过多地忽略沿水深分布信息的缺点 ;二是增强模型的模拟能力。针对这两个目的是否能真正得到体现 ,分别从理论和实验室资料两个方面对新推导的力矩方程进行了全面的检验。理论验证结果表明 ,一维的力矩方程除了能模拟水深平均的流速和含沙量 ,还能够较好地模拟水流泥沙因子沿水深分布信息 ,这充分说明了一维力矩方程的二维特性。为了检验力矩方程的模拟能力 ,特别选取了一些极端的水流泥沙运动实验 ,如清水冲刷、点源加沙和深槽回淤等。模拟结果表明 ,力矩方程对于这些极端的水沙运动具有较好的模拟能力     

探讨缩聚催化剂对聚酯切片质量的影响

通过试验，分析比较了江西Sb2O3、南宁Sb2O3和大连Sb(Ac)3三种缩聚催化剂对聚酯切片质量的影响。试验结果表明，Sb(Ac)3是优良的缩聚催化剂。     

上海东方艺术中心柔性索网体系曲面幕墙安装技术

上海东方艺术中心玻璃幕墙安装在钢架-索网-支撑复杂的钢结构体系上，由立柱横杆、撑杆、钢索组成的空间三维曲面，造型独特别致，对定位测量精度要求高，由于构件刚度小，施工顺序安排及工艺控制对构件安装成型过程的变形和应力影响较大.通过分析比较，介绍了施工顺序和过程控制技术措施，使安装偏差均在5 mm以内。     

Failure analysis used for remanufacturing of steel rolling components

The guide-pieces, used in the process line of steel rolling, were the important components. The guidepieces, which were slide contacting with the rolled-piece, had a high temperature and high speed. The wear was very serious. The results from failure analysis showed that there were three failure forms in the guide-pieces: the first was the wear during heat friction, the second was the heat fatigue under the cycle of deep heating and deep cooling, and the third was the impact rupture. Among them, the wear was the main reason. To the wear of guidepieces, there were four mechanisms, namely abrasive wear, adhesive wear, fatigue wear and corrosion wear. The failure analysis to the guide-piece laid the foundation for its remanufacturing. Foundation item: Project(50235030) supported by the National Natural Science Foundation of China