Characteristics of membrane humidifiers for polymer electrolyte membrane fuel cells

Water management plays an important role in obtaining high performance from a polymer electrolyte membrane fuel cell (PEMFC). To reduce the volume and energy consumption of widely-used bubble humidifiers, membrane humidifiers were fabricated by using an ultrafiltration (UF) membrane and Nafion membranes. The performance of the membrane humidifiers was examined as a function of gas flow rate and operating temperature. A single cell was operated using the UF membrane humidifiers exhibiting almost the same performance with that employing bubble humidifiers.     

The permeation resistance of interface and the directional dependence of permeation in plasma-grafted composite membranes

Composite membranes were prepared by grafting plasma-polymerized films onto the surface of nonporous poly (dimethylsiloxane) films. Gas permeabilities of the composite membranes were measured at 35°C, 1 atm for N₂, 0₂, CO₂ and CH₄. The permeation properties of the composite membrane was analyzed using the series resistance model. There was a great interfacial resistance to CH₄ permeation through the composite membrane. The interfacial resistance was negligible for the other gases. The interfacial resistance seems to be a result of an interfacial layer caused by the interaction between the bulk two layers. For CH₄ gas, the permeation rate through the composite membrane was affected by the direction of flow. The directional dependence was negligible for the other gases.     

Effect of reactive diluents on properties of unsaturated polyester/montmorillonite nanocomposites

Unsaturated polyester (UP)/montmorillonite (MMT) nanocomposite was prepared by using hydroxypropylacrylate (HPA) as a reactive diluent instead of conventional styrene monomer and the effect of polarity of reactive diluent on properties of nanocomposite was investigated. X‐ray and mechanical test data indicated that mixing for an extended period of time is essential to enhance the physical properties of nanocomposites in the UP/Cloisite 6A system. This was attributed to the high polarity of HPA that may disturb the preintercalation of UP resin into the galleries of MMT. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 238–242, 2004     

Dynamic mechanical properties of three different combinations taken from styrene-co-itaconate, styrene-co-methacrylate, and styrene-co-sulfonate ionomers

Dynamic mechanical properties of three different styrene-based ionomer blends containing ca. 5 mol% of ionic repeat units were investigated; the three ionic units were itaconate (ITANa), methacrylate (MANa), and styrenesulfonate (SNa). For SNa-MANa ionomers, it was observed that this ionomer system showed only two loss tangent peaks, implying that this ionomer system resembles a typical miscible system. When the ion content increased, however, the ionomer blend showed two cluster loss tangent peaks, indicating the presence of phase-separated cluster regions. This suggests that, with increasing ion content, the role of ionic units becomes more important than that of host non-ionic units to determine ionomer properties. In the case of ITANa-MANa and ITANa-SNa ionomers, however, it was suggested that the multiplets of the MANa and SNa ionomers might be disrupted upon the addition of the ITANa ionomers. In addition, the SEM images showed that the fracture surfaces of ionomers changed upon blending.     

Monodisperse polymer/metal composite particles by electroless chemical deposition: Effect of surface functionality of polymer particles

Micron‐sized polymer particles were coated with layers of nickel compounds by plating electrolessly in the presence of aqueous solutions of nickel chloride, sodium hypophosphite, sodium citrate, and ammonium chloride at elevated temperature. The uniform functional polymer particle could be obtained by seeded polymerization. To investigate the effect of surface functionality on the conditions for nickel deposition, the polymer particle was functionalized with the thiol group. From morphological observation, it was found that the mode of nickel deposition was greatly dependent on the surface functionality of the polymer particle. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 420–424, 2003     

Preparation of nano-sized silicon carbide powder using thermal plasma

Nano-sized silicon carbide (SiC) powder was prepared by thermal plasma process using silicon tetrachloride (SiCl₄) and methane (CH₄). The synthesized powder was characterized by X-ray diffraction pattern, scanning electron microscopy, transmission electron microscopy, FT-IR spectroscopy and particle size analyzer. The powder was dominated by β-SiC including some of α-SiC and free carbon species. The quality of the powder was varied with process conditions such as the molar ratio of H/Si and C/Si, and collecting positions. It was known that the conversion to SiC was mainly affected by the addition of hydrogen gas because it promoted the decomposition and reduction of SiCL. CH₄ was easily decomposed to carbon species for the formation of SiC as well as removal of impure oxygen, but excessive carbon suppressed the formation of crystalline SiC and resulted in the solid carbon contamination. The optimum ratio of H/Si was approx. 26 and that of C/Si was 1.1. For collecting positions, the powder collected at the vessel and filter was preferable to that at the reaction tube. The average size of the powder synthesized was estimated to be below 100 nm and uniform in distribution.     

Thermal and mechanical properties of the polymers synthesized by the sequential polymerization of propylene and 1‐hexadecene

The block copolymer of poly(1‐hexadecene) (PHD) and polypropylene (PP) was effectively synthesized by the sequential polymerization of propylene and 1‐hexadecene by using highly isospecific TiCl₃/Cp₂Ti(CH₃)₂ (Cp = cyclopentadienyl). The block copolymers had two separate melting temperatures of constituent blocks. The modulus of PHD–PP block copolymer was enhanced as the content of sequentially polymerized PP block was increased. The elongation at break showed positive deviation at the intermediate compositions from the simple additive values of constituent homopolymers. Shape memory effect which utilizes the crystalline PHD block as a reversible phase and the crystalline PP block as a fixed structure was examined. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1709–1715, 2002; DOI 10.1002/app.10551     

On Robust Approximate Feedback Linearization: Control with Two Gain-scaling Factors

In this paper, we consider a problem of global stabilization for a class of approximately feedback linearized nonlinear systems. In order to handle more nonlinearity over the existing results, we provide a new feedback controller with two gain-scaling factors and we show that more nonlinearity can be treated by our control scheme. Moreover, we analytically show that the considered nonlinear systems can be stabilized by the proposed controller. Through comparison practical examples, we illustrate the improved features of our proposed control method.

     

Improved Controller Design with Two Gain-scaling Factors for Global Asymptotic Stabilization of Nonlinear Systems via Matrix Inequality Approach

In this paper, we consider a problem of global asymptotic stabilization for nonlinear systems with the perturbed nonlinearity. We provide a stabilizing controller with two gain-scaling factors and a new controller design method with matrix inequality approach. In particular, we provide a new procedure for selecting gain-scaling factors which are associated with stabilizing the closed-loop system. As a result, our proposed control method widens the class of considered nonlinear systems and yields better control performance over the existing methods. Via several comparison examples, we illustrate the improved features of the proposed control method over the existing ones.

     

Prediction of forming limit in hydro-mechanical deep drawing of steel sheets using ductile fracture criterion

It has been observed that the forming limit curve at fracture (FLCF) of steel sheets, with a relatively higher ductility limit have linear shapes, similar to those of a bulk forming process. In contrast, the FLCF of sheets with a relatively lower ductility limit have rather complex shapes approaching the forming limit curve at neck (FLCN) towards the equi-biaxial strain paths. In this study, the FLCFs of steel sheets were measured and compared with the fracture strains predicted from specific ductile fracture criteria, including a criterion suggested by the authors, which can accurately describe FLCFs with both linear and complex shapes. To predict the forming limit for hydro-mechanical deep drawing of steel sheets, the ductile fracture criteria were integrated into a finite element simulation. The simulation, results based on the criterion suggested by authors accurately predicted the experimetal, fracture limits of steel sheets for the hydro-mechanical deep drawing process.