Electrodeposition of nickel in the presence of Al<Superscript>3+</Superscript> from sulfate baths

The effect of Al³⁺ on the cathodic current efficiency, deposit morphology, crystallographic orientations and polarisation behaviour of the cathode during electrodeposition of nickel from acidic sulfate solutions was investigated. Higher concentration of Al³⁺ (>10 mg dm^–3) significantly deteriorated the surface quality of the nickel deposit as well as the current efficiency. X-ray diffraction studies revealed that the (200) plane was the most preferred crystal plane and was not affected by the presence of varying concentration of Al³⁺ in the electrolytic bath. The presence of Al³⁺ caused polarisation of the cathode, which increased with increasing Al³⁺ concentration. The effect of Al³⁺ on the electrokinetic parameters: Tafel slope (b), transfer coefficient () and exchange current density (i₀) were also investigated.     

Mechanical,thermal and dynamic‐mechanical behavior of banana fiber reinforced polypropylene nanocomposites

Natural fiber‐reinforced nanocomposites based on polypropylene/nanoclay/banana fibers were fabricated by melt mixing in a twin‐screw extruder followed by compression molding in this current study. Maleic anhydride polypropylene copolymer (MA‐g‐PP) was used as a compatibilizer to increase the compatibility between the PP matrix, clay, and banana fiber to enhance exfoliation of organoclay and dispersion of fibers into the polymer matrix. Variation in mechanical, thermal, and physico‐mechanical properties with the addition of banana fiber into the PP nanocomposites was investigated. It was observed that 3 wt% of nanoclay and 5 wt% of MA‐g‐PP within PP matrix resulted in an increase in tensile and flexural strength by 41.3% and 45.6% as compared with virgin PP. Further, incorporation of 30 wt% banana fiber in PP nanocomposites system increases the tensile and flexural strength to the tune of 27.1% and 15.8%, respectively. The morphology of fiber reinforced PP nanocomposites has been examined by using scanning electron microscopy and transmission electron microscopy. Significant enhancement in the thermal stability of nanocomposites was also observed due to the presence of nanoclay under thermogravimetric analysis. Dynamic mechanical analysis tests revealed an increase in storage modulus (E′) and damping factor (tan δ), conforming the strong interaction between nanoclay/banana fiberand MA‐g‐PP in the fiber‐reinforced nanocomposites systems. POLYM. COMPOS., © 2011 Society of Plastics Engineers.     

Effect of Maleated Compatibilizer on Performance of PLA/Wheat Straw‐Based Green Composites

In this study, the use of PLA‐g‐MA is investigated as a potential method for improving interfacial adhesion between agricultural residues and PLA, with the goal of enhancing mechanical properties. Compatibilization was achieved by using PLA‐g‐MA prepared via reactive extrusion. Green renewable and compatibilized PLA/wheat straw composites were extruded and injection‐molded. Addition of 3 and 5 phr PLA‐g‐MA to the composites resulted in significant improvements in tensile strength (20%) and flexural strength (14%) of the composites, matching that of the neat polymer. The observed improvement in strength was attributed to the good interfacial adhesion between the fiber and matrix.

     

The Effects of Process Engineering on the Performance of PLA and PHBV Blends

The effects of process engineering in the fabrication of PHBV, PLA and their blends prepared by melt blending are studied. The elongation of an optimized blend can be improved by 148 and 250% over the virgin PHBV and PLA polymers, respectively. DSC shows that the two polymers are immiscible in blends of any composition. The crystallinity of PHBV is hindered by the presence of PLA. UV‐Vis demonstrates the opacity of the blend with incorporation of PHBV to the PLA phase. The observed tensile modulus of the optimized sample is compared with theoretical values from the rule of mixtures. Gordon‐Taylor's equation is applied on the glass transition temperatures for theoretical modeling to explain the miscibility of the polymers.

     

Synthesis and characterization of magnetic nanocomposites of fullerene‐containing polyurethane films for microwave applications

Novel nanocomposites of barium hexaferrite‐ and fullerene‐containing polyurethane were synthesized and characterized by scanning electron microscopy, transmission electron microscopy, X‐ray diffractometry, and energy‐dispersive X‐ray diffraction. The nanoparticles showed good dispersion in the polyurethane matrix. Their thermal, mechanical, and electromagnetic absorbance properties were studied. The complex permeability and permittivity were measured in the frequency range of 8.2–12.4 GHz. The maximum reflection loss of the nanocomposites was found to increase with increasing the ferrite content from 1% to 5%, with maximum value of −7.5 dB at only 5% composition. The incorporation of nanofiller not only imparts mechanical strength to the nanocomposite but also shows good radar‐absorbing properties at only 5% filler concentration. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Processable high Tg high strength fluorinated new poly(arylene ether)s containing imido aryl group

A series of poly(arylene ether)s ( 7a–7f ) were successfully synthesized by aromatic nucleophilic substitution reactions of imidoaryl biphenol (5), 4,9‐bis‐(4‐hydroxy‐phenyl)‐2‐phenyl‐benzo[f]isoindole‐1,3‐dione with six different trifluoromethyl substituted bisfluoro monomers ( 6a–6f ). The weight‐average molar masses of the polymers were up to 280 kD as measured by GPC. These poly(arylene ether)s exhibited glass transition temperatures up to 361°C in DSC. These polymers showed very high thermal stability up to 558°C for 10% weight loss under synthetic air in TGA. Except 7d–7f, remaining polymers 7a–7c were soluble in a wide range of organic solvents. Transparent thin films of these polymers cast from DCM or NMP exhibited tensile strengths up to 75 MPa and elongation at break up to 41% depending on their exact repeating unit structures. These poly(arylene ether)s showed cut‐off wavelength in between 400 and 450 nm except 7d and water absorption were in the range of 0.4 to 0.6%. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Surface modification of coir fibers. II. Cu(II)‐ IO initiated graft copolymerization of acrylonitrile onto chemically modified coir fibers

A study of the graft copolymerization of acrylonitrile (AN) onto chemically modified coir fibers was carried out using a CuSO₄ and NaIO₄ combination as the initiator in an aqueous medium in a temperature range of 50–70°C. The graft yield was influenced by the reaction time, temperature, concentration of CuSO₄, concentration of NaIO₄, and monomer concentration. Grafting was also carried out in the presence of inorganic salts and organic solvents. A combination of copper(II) and sodium periodate (Cu²⁺‐IO) in an aqueous medium with an IO concentration of 0.005 mol L^?1 and a Cu²⁺ concentration of 0.004 mol L^?1 produced optimum grafting. The chemically modified and AN grafted fibers were characterized by FTIR and scanning electron microscopy (SEM). The SEM studies revealed that grafting not only takes place on the surface of the fibers but also penetrates the fiber matrix. The tensile properties like the maximum stress at break and extension at break of untreated, chemically modified, and AN grafted coir fibers were evaluated and compared. The extent of absorption of water of untreated, chemically modified, and grafted coir fibers was determined. It was found that grafting of AN imparts hydrophobicity onto coir fibers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 75–82, 2002; DOI 10.1002/app.10221     

Use of novel hydrogels based on modified cellulosics and methacrylamide for separation of metal ions from water systems

Interpenetrating networks (IPNs) based on extracted cellulose and its derivatives such as hydroxypropyl cellulose (HPC), cyanoethylcellulose, hydroxyethylcellulose, hydrazinodeoxycellulose, cellulosephosphate with methacrylamide (MAAm), and N,N‐methylene bisacrylamide were synthesized at reaction conditions evaluated for optimum network yield as a function of irradiation dose, concentrations of monomer and crosslinker, and amount of water. These networks were used in sorption of Fe²⁺, Cu²⁺, and Cr⁶⁺ ions. The networks were further functionlized by means of partial hydrolysis with 0.5N NaOH and metal ion sorption studies were carried out. Appreciable amount of all the three ions was sorbed and partial functionalization of the hydrogels results in selectivity in ion sorption with enhanced affinity for Fe²⁺ ions and total rejection of Cr⁶⁺ ions. These results are of interest for the development of low‐cost technologies based on smart hydrogels. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 667–671, 2002     

Microwave-Assisted Synthesis of Fine Particle Oxides Employing Wet Redox Mixtures

Interaction of electromagnetic radiation with a physical mixture of metal nitrates and amides/hydrazides is observed to initiate high-temperature reactions, useful for realizing several high-temperature ceramic materials. A judicious choice of such redox mixtures undergoes exothermic reactions when they couple with microwave radiation. The coupling of electromagnetic radiation with metal salts and amides/hydrazides depends on the dielectric properties of the individual components in the reaction mixture. The approach has been used to prepare γ-Fe₂O₃, Fe₃O₄, MgCr₂O₄, α-CaCr₂O₄, and La_0.7Ba_0.3MnO₃.