Enhanced electron emission from phosphorus-doped diamond-cladsilicon field emitter arrays

Undoped and phosphorus (P)-doped diamond-clad Si field emitter arrays have been successfully fabricated using microwave plasma chemical vapor deposition (MPCVD) technology. The electron emission from the blunt diamond-clad microtips are much higher than those for the pure Si tips with sharp curvature due to a lower work function. Furthermore, the characteristics of emission current against applied voltage for the P-doped diamond-clad tips show superior emission at lower field to the undoped ones. After the examination of Auger electron spectroscopy (AES) and electrical characteristics of as-grown diamond, such a significant enhancement of the electron emission from the P-doped diamond-clad tips is attributed to a higher electron conductivity and defect densities     

Extinction of dispersed heterogeneous systems

We consider extinction of various dispersed systems. Isolated boron particles and boron particles in gases are studied. Stability analysis of steady-state thermal regimes of reacting heterogeneous systems for the case of two parallel reactions on the reaction surface using the Frank-Kamenetskii method gives extinction conditions in oxygen-containing media. Curves of the extinction particle size versus the ambient temperature, oxidizer concentration, and, for particles in gases, also versus the oxidizer-to-fuel ratio are plotted. Approximate analytical calculations showed that the extinction process can be most actively controlled by varying the combustion temperature: a decrease in the latter increases the extinction particle size and decreases the completeness of fuel combustion. It is shown that at low ambient temperatures the extinction particle size for suspensions is larger than that for isolated particles. This effect is caused by a decrease in the oxidizer concentration during combustion of suspensions. At high temperatures, the role of this factor weakens.Translated from Fizika Goreniya i Vzryva, Vol. 32, No. 6, pp. 12–19, November–December, 1996.     

Sensorless speed measurement using current harmonic spectralestimation in induction machine drives

This paper proposes a sensorless speed measurement scheme that improves the performance of transducerless induction machine drives, especially for low-frequency operation. Speed-related harmonics that arise from rotor slotting and eccentricity are analyzed using digital signal processing. These current harmonics exist at any nonzero speed and are independent of time-varying parameters, such as stator winding resistance. A spectral estimation technique combines multiple current harmonics to determine the rotor speed with more accuracy and less sensitivity to noise than analog filtering methods or the fast Fourier transform. An on-line initialization routine determines machine-specific parameters required for slot harmonic calculations. This speed detector, which has been verified at frequencies as low as 1 Hz, can provide robust, parameter-independent information for parameter tuning or as an input to a sensorless flux observer for a field-oriented drive. The performance of the algorithm is demonstrated over a wide range of inverter frequencies and load conditions     

Application of evolutionary programming to transient andsubtransient parameter estimation

This paper presents an artificial intelligence approach of using evolutionary programming to estimate the transient and subtransient parameters of a generator under normal operation. The estimation using evolutionary programming is compared with that using a corrected extended Kalman filter. The comparisons with both simulation and micromachine test results show that evolutionary programming is robust to search the real values of parameters even when the data are highly contaminated by noise, while with the extended Kalman filter, the estimation tends to diverge with such data     

Effect of type of processing on the microstructural features and mechanical properties of Al-Cu/SiC metal matrix composites

In this study, an aluminum based metallic matrix (Al-2wt.% Cu) was reinforced with SiC particulates using a conventional casting technique and a new disintegrated melt deposition technique. Microstructural characterization studies conducted on the samples taken from disintegrated melt deposition technique revealed a more uniform distribution of SiC particulates and good interfacial integrity between SiC particulates and metallic matrix when compared to the conventionally cast composite samples. Results of ambient temperature mechanical tests demonstrate an increase in 0.2% YS and ultimate tensile strength of samples taken from disintegrated melt deposition technique when compared with the unreinforced and conventionally cast composite samples. The results of microstructural characterization and mechanical testing were finally rationalized in terms of the nature of processing technique employed to reinforce Al-2wt.% Cu metallic matrix with SiC particulates.     

Pharmacodynamic Comparison of a Nasal Formulation of Verapamil and Intravenous and Oral Dosage Forms

The nasal route has been shown to be effective for the administration of numerous drugs in order to improve drug bioavailability. A nasal gel of verapamil hydrochloride was formulated and evaluated pharmacodynamically in humans, using electrocardiographic results, with comparison to oral and IV routes. Seven volunteers were involved in the study and the pharmacodynamic parameters were evaluated statistically. Experimental nasal gel showed similar pharmacodynamic results with the intravenous route, which is a hint to the reduction in verapamilinduced first-pass metabolism. However, oral route of administration showed a tendency of less efficacy. No reasonable effect of verapamil could be obtained with the placebo group.     

Highly reliable testing of ULSI memories with on-chip voltage-downconverters

Two testing techniques for ultra-large-scale integrated (ULSI) memories containing on-chip voltage downconverters (VDCs) are described. The first in an on-chip VDC tuning technique that adjusts internal V_CC to compensate for the monitored characteristics of the process parameters during repair analysis testing. The second is an operating-voltage margin test, performed at various internal V_CC levels during the water sort test (WT) and the final shipping test (FT)     

Abnormal behavioral responses to fenfluramine in patients with affective and personality disorders. Correlation with increased serotonergic responsivity

Serotonergic responsivity was assessed in 20 psychiatric patients by the prolactin response to a fenfluramine challenge test. During the fenfluramine challenge 6 of 20 patients (30%) spontaneously reported psychopathologic reactions that included: increased anxiety/agitation, psychotic symptoms, illusions, mood elevation, and anergia. The time of peak behavioral symptoms (2.5 +/- 0.8 hrs) corresponded closely to the time of peak increase in prolactin levels (3.0 +/- 1.1 hr). Abnormal behavioral responders had statistically significant greater increases in prolactin 1 to 4 hr after fenfluramine when compared to normal responders. Patients who developed an abnormal psychopathologic response to fenfluramine were characterized by higher levels of anxiety and agitation at the time of admission to the hospital but otherwise were not distinguishable on the basis of severity of other psychiatric symptoms. This study suggests that increased serotonergic transmission may trigger anxiety, psychosis, and mood elevation in specific vulnerable individuals, whereas other patients with similar psychiatric illnesses are not affected.     

Adiabatic couplers: design rules and optimization

Explicit analytic design rules are derived for both 3 dB and full adiabatic couplers. The design rules are in excellent agreement with numerical calculations using the beam propagation method (BPM). It is shown that the length scaling for 3 dB couplers compared to full couplers makes the former more difficult to design. The design for each case is optimized to obtain the upper limit of performance and a comparison is carried out between two different design geometries for both 3 dB and full adiabatic couplers