High-speed picosecond optical pulse compression from gain-switched 1.3-µm distributed feedback-laser diode (DFB-LD) through highly dispersive single-mode fiber

Picosecond optical pulse compression characteristics of chirped pulses from gain-switched distributed feedback-laser diodes (DFB-LD) transmitting through highly dispersive media are studied theoretically and experimentally. It is clarified theoretically that gain-switched chirped pulses can be compressed to about a 0.7-time bandwidth product by normal dispersion of the dispersive media and that the optimum dispersion value to obtain a minimum compressed pulse is proportional to the square of original pulsewidth. Through a dispersion, shifted single-mode fiber with -48-ps/nm normal dispersion at a 1.3-μm wavelength, gain-switched 30-ps (FWHM) pulses from a directly modulated 1.3-μm DFB-LD at a 4.4-GHz repetition rate have been successfully compressed to 6.4-ps optical pulses with a 0.86-time bandwidth product. Experimental results agree with the theoretical analysis.     

Survival of Yersinia enterocolitica and Escherichia coli in spring water

Survival of pure and mixed cultures of Yersinia enterocolitica and Escherichia coli in sterile spring water stored at 4 degrees C was evaluated. Y. enterocolitica increased two or three logs during the first 3 weeks of incubation, and at the end of 64 weeks viable cells in numbers corresponding to the initial inoculum level were still detectable. However, after 1 week of incubation, the number of E. coli in water started to decrease and in 13 weeks time no E. coli was detected. More rapid decrease of E. coli was observed in mixed cultures.     

Simulation of sulfide buildup in wastewater and atmosphere of sewer networks.

A model concept for prediction of sulfide buildup in sewer networks is presented. The model concept is an extension to--and a further development of--the WATS model (Wastewater Aerobic-anaerobic Transformations in Sewers), which has been developed by Hvitved-Jacobsen and co-workers at Aalborg University. In addition to the sulfur cycle, the WATS model simulates changes in dissolved oxygen and carbon fractions of different biodegradability. The sulfur cycle was introduced via six processes: 1. sulfide production taking place in the biofilm covering the permanently wetted sewer walls; 2. biological sulfide oxidation in the permanently wetted biofilm; 3. chemical and biological sulfide oxidation in the water phase; 4. sulfide precipitation with metals present in the wastewater; 5. emission of hydrogen sulfide to the sewer atmosphere and 6. adsorption and oxidation of hydrogen sulfide on the moist sewer walls where concrete corrosion may take place.     

Personal spaces — ePerSpace

This paper describes the ePerSpace research project which aims to significantly increase user acceptance of networked audiovisual systems and applications at home and virtually anywhere by enabling innovative interoperable value-added personalised networked services and applications. Moreover, it aims to develop an open architecture and a framework that will significantly increase the speed of developing novel value-added personalised services by reusing well-defined system components with open APIs. The structure of the paper follows the methodology of the project. It starts with a vision of future personalised services from the users’ perspective by developing five scenarios. These scenarios are then used to extract the requirements of the personalisation framework which is then described in terms of its personalisation, service management, digital home environment management and content adaptation capabilities.     

Highly integrated direct conversion receiver for GSM/GPRS/EDGE with on-chip 84-dB dynamic range continuous-time /spl Sigma//spl Delta/ ADC

This paper describes a highly digitized direct conversion receiver of a single-chip quadruple-band RF transceiver that meets GSM/GPRS and EDGE requirements. The chip uses an advanced 0.25-/spl mu/m BiCMOS technology. The I and Q on-chip fifth-order single-bit continuous-time sigma-delta (/spl Sigma//spl Delta/) ADC has 84-dB dynamic range over a total bandwidth of /spl plusmn/135 kHz for an active area of 0.4 mm/sup 2/. Hence, most of the channel filtering is realized in a CMOS IC where digital processing is achieved at a lower cost. The systematic analysis of dc offset at each stage of the design enables to perform the dc offset cancellation loop in the digital domain as well. The receiver operates at 2.7 V with a current consumption of 75 mA. A first-order substrate coupling analysis enables to optimize the floor plan strategy. As a result, the receiver has an area of 1.8 mm/sup 2/.     

Pull-out and fragmentation in model fibre composites

An experimental study has been carried out of debonding and fibre rupture in model composites. A single glass rod or fibre was embedded in the centre of a long transparent silicone rubber block. Strains in the rubber in close proximity to the rod or fibre were measured as the specimen was slowly stretched. Pull-out forces, strain distributions, and debonded lengths are compared with the predictions of a simple theory based on a fracture energy criterion for debonding, and taking into account friction at the debonded interface. Experiments were carried out with rods of different diameter, rubber blocks of varied cross-section, and with two levels of adhesion. By extrapolating the debonded length to zero, values of the debonding force in the absence of friction were obtained. They were in accord with fracture energies of about 50 J/m² for weak bonding and about 200 J/m² for strong bonding. Fibre fragmentation lengths were measured also. They were in reasonable agreement with the inferred fracture energies and the measured frictional properties of silicone rubber sliding on glass. In a separate study, it was found that the frictional stress between cast silicone rubber and glass was approximately constant, about 0.1 MPa, rather than proportional to pressure, for pressures exceeding about 0.02 MPa. This feature is attributed to a particularly smooth interface between the two materials.     

High spatial order finite element method to solve Maxwell's equations in time domain

This paper presents a finite element method with high spatial order for solving the Maxwell equations in the time domain. In the first part, we provide the mathematical background of the method. Then, we discuss the advantages of the new scheme compared to a classical finite-difference time-domain (FDTD) method. Several examples show the advantages of using the new method for different kinds of problems. Comparisons in terms of accuracy and CPU time between this method, the FDTD and the finite-volume time-domain methods are given as well.