Network model approach for calculating oscillating frequency of thermoacoustic prime mover

The network model is given and used to calculate the oscillating frequency of thermoacoustic prime mover. Theoretically calculated frequency by the model is plural, whose real part denotes actual frequency of the system, and imaginary part means attenuation coefficient of acoustic pressure. Numerical calculation is made under different conditions including different acoustic cavities, spacing between each parallel plate, gas pressures and system lengths. Theoretically calculated frequency and experimentally measured frequency are in quite good agreement.     

快速搜寻卫星数字压缩信号

在没有专业仪器，没有明确参照物的条件下，如何快速定位接收天线，搜索到卫星信号，是电视工程技术人员经常遇到的问题，本文就此问题提出了一个新的解决办法，即利用已知卫星的位置来定位其它卫星的位置。     

发电机同轴励磁机电刷火花过大的原因及处理方法

本文对发电机同轴励磁机电刷火花过大的原因进行了分析．并针对这些原因提出了相应的处理办法。对规范励磁机的运行维护有很大的帮助。     

影响喷气燃料与橡胶相容性的因素

采用几种具有不同初始物理性能及不同丙烯腈含量、不同硫化剂和硫化程度的丁腈橡胶，考察了其配方和物理性能对采用不同工艺条件生产的喷气燃料的相容性。结果表明，喷气燃料与橡胶的相容性不仅与喷气燃料的加工工艺有关，而且与橡胶的组成及其制备工艺有关。采用非加氢工艺生产的喷气燃料与橡胶的相容性好于采用加氢工艺(特别是加氢裂化工艺)生产的喷气燃料。橡胶材料的初始力学性能的好坏并不完全决定其与喷气燃料相容性的好坏，橡胶材料的耐过氧化物侵蚀能力才是影响相容性好坏的主要因素。橡胶的组成和其制备工艺决定了橡胶在喷气燃料中萃取物的数量和组成，不同萃取物的综合作用给相容性带来不同程度的影响。用硫作硫化剂的橡胶虽然原始强度低于用过氧化物作硫化剂的橡胶，但前者与喷气燃料的相容性却远好于后者。     

高度有序多孔氧化铝模板的制备工艺与生长机制的研究

采用二次氧化法制备出高度有序的多孔氧化铝模板，结合扫描电镜和原子力显微镜对其结构、形貌进行观察和表征。研究了铝箔预处理和温度等对多孔氧化铝模板孔洞有序性的影响，讨论了有序孔洞的自组织生长机理。     

高等植物氨基酸生物效应的研究进展

本文对氨基酸营养条件下植物体内硝酸盐含量变化及其机理,土施植物激素前体色氨酸和蛋氨酸对高等植物生长和化学组成的影响。氨基酸和氨基酸肥料对植物产量和品质的影响作了综述。     

N,N′-二(β-十八酰氧基)乙基乙二胺二乙酸钠的合成及性能研究

用 N,N′-二羟乙基乙二胺、氯乙酸钠合成了 N,N′-二羟乙基乙二胺二乙酸钠(中间体),中间体再与硬脂酰氯反应制备了一种新型 Gemini 两性表面活性剂 N,N′-二(β-十八酰氧基)乙基乙二胺二乙酸钠。对产物合成条件进行了考察,优化的反应条件为:n(硬脂酰氯):n(中间体)=2.5,溶剂 V(水):V(氯仿)=1:2,pH=9.0～10.0,反应温度15～20℃,反应时间5 h。通过红外光谱和质谱分析确定了产物结构,并测试了产物的表面性能。结果表明,在25℃时,该产物的临界胶束浓度为0.24 mmol/L,临界胶束浓度下的表面张力为35.7 mN/m;即时泡沫高度为250 mm,5 min 后泡沫高度为220 mm;乳化时间为22.48 min(甲苯-水物系)和4.65 min(正己烷-水物系),亲水-亲油平衡值为5.4,等电点为 pH 3.3～6.5。     

Signature analysis and defect detection in layered manufacturing of ceramic sensors and actuators

This paper presents the concept of a process signature for the use of online signature analysis and defect detection in the layered manufacturing (LM) of ceramic sensors and actuators. To achieve the high quality of parts built by the fused deposition of ceramics (FDC), an online process-monitoring system is implemented to detect the processing defects. Using a process signature extracted from the image of a layer captured by the monitoring system, an ideal image is created that is then compared to the original image to detect and identify the defects. Some results of signature analysis and defect detection for single-material and multi-material parts are also presented.Received: 22 July 1999, Accepted: 21 October 2001, Published online: 29 October 2003 Correspondence to: Mohsen A. JafariThis work was supported by the Office of Naval Research under grant # N-0014-96-1-1175. Ref. US Patent # S-5738817, April 14, 1998.     

Application of ultrasonic waves in activation of microcrystalline cellulose

In this work, microcrystalline cellulose (MCC) was activated with ultrasonic waves. The influences of ultrasonic treatment on the changes of supramolecular structures and morphology structure were studied by WAXS and SEM. The accessibility of the MCC was characterized by water retention value (WRV) and specific surficial area. The influence of ultrasonic treatment on the reactivity of MCC was investigated through the reaction of MCC being oxidized into 2,3‐diadehyde cellulose (DAC) by periodate sodium. The mechanism of the reactivity change of ultrasonically treated MCC was examined. The results showed that the degree of crystallinity of MCC decreased and the degree of polymerization showed little change after treatment with ultrasonic waves. The morphologial variation of the treated MCC was significant when compared with the untreated MCC, which contribute to the improvement of accessibility. The aldehyde content of DAC prepared from ultrasonically treated MCC was improved from 64.19 to 85.00%, indicating that the regioselective oxidation reactivity of MCC was significantly improved. The aldehyde content was found to first increase with time of ultrasonic treatment to a point, and then decrease as time progressed. In addition, the aldehyde content was found to increase with an increase in ultrasonic power. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008