The study of activity median aerodynamic diameter using imaging plate technique for assessment of effective dose from radon and its decay products

The indoor workplace environment was evaluated for exposure to radon and its decay products at two Universities in two metropolises of Japan. The mean radon concentrations in Nagoya University (NU) and Hokkaido University (HU) were 16.7 Bq m(-3) and 18.0 Bq m(-3), respectively. Activity median aerodynamic diameter (AMAD) of particles at NU ranged from 172 nm approximately 205 nm and at HU from 186 nm approximately 300 nm. Estimated effective doses for five usual sites of NU by ICRP approach was 0.15 mSvy(-1) approximately 0.76 mSvy(-1) and by UNSCEAR approach was 0.05 mSvy(-1) approximately 0.24 mSvy(-1). The effective dose for the same of HU by ICRP 66 approach was 0.16 mSvy(-1) approximately 0.79 mSvy(-1) and by UNSCEAR 2000 approach was 0.05 mSv y(-1) to 0.26 mSv y(-1). The two approaches differs on an average by a factor 2.3- approximately 4.7. The AMAD of obtained particle size distribution at NU has an average total deposition of 23% in human respiratory tract and 20% at HU.     

Optical-fibre network system for air-pollution monitoring over a wide area by optical absorption method

A low-loss optical-fibre network system for monitoring air pollution and species concentrations in various environments utilising the differential absorption method is proposed and discussed as a sensitive and economical as well as nonhazardous method. Its feasibility and advantages are also described on the basis of the present state of the art of the relevant technology.     

Analysis of upgraded solvent-refined coal (SRC) liquid products

Upgraded coal-derived liquids obtained from catalytic hydroprocessing of a 30–70(wt%) blend of SRC-1 with SRC-II have been studied by infrared and proton magnetic resonance spectroscopy, and gel permeation chromatography techniques. Compared with the feed blend, the upgraded liquids exhibit a lower C/H ratio and decreased aromatic, heteroatom and pentane-insoluble contents, along with decreased specific gravity and viscosity. The amount of hydrogen-bonded structure in the upgraded liquid decreases with increases in residence time and processing temperature. The pseudo-first-order disappearance of phenolic OH and total nitrogen during processing indicates a relative reactivity of 2:1 of hydroxyl oxygen removal to total nitrogen removal in the upgrading process. Conversion of pentaneinsolubles to soluble oil also follows a pseudo-first-order reaction; under mild processing conditions, the heteroatom functionalities play a dominant role in the ease and extent of this conversion. Higher temperatures increase thermal cracking and hydrocracking of the ring structure resulting in more conversion of asphaltene to oil. The linear dependence of the logarithm of viscosity on the content of heteroatoms and toluene-insolubles (TI) indicates the importance of molecular interactions involving polar functional groups in defining the viscosity of coal-derived liquid.     

An application of rapid freezing,freeze substitution–fixation for scanning electron microscopy

A combined technique of the rapid freezing, freeze substitution–fixation method and the osmium–DMSO-osmium method was devised. By this combined method we clearly observed the architecture of intracellular components in three dimensions. Morphological characteristics were generally similar to those of tissue prepared by the osmium–DMSO-osmium method but different in some respects. Mucigen droplets in intestinal goblet cells, for example, appeared as separated spheres, while in specimens prepared by chemical fixation they were observed as a mass of fused droplets. In the Golgi complex, all cisternae were extremely flat, although they usually dilated on the cis side after chemical fixation. Particles on the mitochondrial tubules of liver cells were well distinguished. They were mushroom shaped, as are those observed by negative staining. The combined method, that is, the rapid freezing, osmium–DMSO-osmium method, is thought to be effective for studying the true structure of intracellular components by scanning electron microscopy.     

Influence of alloy composition on fillet-lifting phenomenon in Sn-Ag-Bi alloys

The influence of the Bi content on the fillet-lifting phenomenon in Sn-3Ag-Bi alloys was investigated. The peculiar composition dependence on the fillet-lifting exists in Sn-3Ag-xBi alloys. With fillet-lifting, they are 3–20%Bi. Without fillet-lifting, they are 0–1%Bi, 30%Bi, and above. This is related to the alloy solidification characteristics, in particular, the amount of latent heat release near the final solidification temperature (solidus temperature) during solidification. Fillet-lifting is likely to occur in the alloy with a latent heat released which is insufficient for alleviation of the temperature gradient in the solder joint. A new predictable index for the occurrence of fillet-lifting is proposed as the fillet-lifting resistant index (FRI) that correlates well with the fillet-lifting occurrence rate. The fillet-lifting does not occur when a solder alloy has a FRI of 0.75 and above. The magnitude of the solidification temperature range (T) does not necessarily correlate with the fillet-lifting, because there are some alloys without fillet-lifting in spite of their having a wide T. There is also little correlation between the fillet-lifting and the formation of a Bi concentration at the solder/Cu land interface, previously thought to cause fillet-lifting. The Bi concentration at the solder/Cu land interface may occur as a consequence of the Sn consumption by the intermetallic compound formation with the Cu dissolving into the molten solder and existing at the interface rather than the solidification segregation.     

Application of polymer gels containing side‐chain phosphate groups to drug‐delivery contact lenses

Hydrogels that contain phosphate groups in side chains were studied for their usefulness in drug‐delivery soft contact lenses (SCLs). Naphazoline, a model drug having a cationic group, was incorporated into an SCL because of its phosphate groups and was released over a period of about 14 h. For the SCL, the naphazoline content was equivalent to the phosphate group content. It is suggested that drug‐delivery SCLs can be designed to contain the needed amount of a drug through the choice of the ionic group for the ligand. Furthermore, the SCL having amide groups and phosphate groups had high transparency and an unchanged shape. It is suggested that amide groups and phosphate groups must be introduced into the polymer in equimolar amounts to give the necessary polymer–drug interaction. Therefore, hydrogels having a drug‐delivery system were synthesized by the inclusion of a phosphate group and an amide group. These hydrogels are also applicable to SCL materials. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 731–735, 2005     

Binding of chrysophenine G by methyl cellulose and poly(vinyl alcohol)

Equilibrium constants (nK) for the binding of Chrysophenine G by methyl cellulose (MC) and poly(vinyl alcohol) (PVA) were determined spectrophotometrically in the temperature range 15–40°C. The polymer chains of PVA extended by the dye binding but those of MC shrank slightly. The enthalpy change and the entropy change for the binding by MC were negative and positive, respectively, whereas those for the binding by PVA were both negative. When the dye was bound to the extended polymer chains, the contribution of the entropy term to the binding increased. The rate of the dye bindings was studied by means of the temperature jump method. For the dye binding to PVA, the whole relaxation process finished in a very rapid step. On the other hand, for dye binding to MC, the initial rapid step was followed by two successive slower steps; the relaxation times for the slower steps were independent of the polymer concentration. The results were interpreted in terms of the stiffness of polymer chain of MC; the conformational change of the stiff chains to accommodate the dye in stable states seems to be the rate determining step in each slow relaxation.     

Japanese research and development on metallic biomedical,dental, and healthcare materials

There is considerable demand for metallic materials for use in medical and dental devices. Metals and alloys are widely used as biomedical materials and are indispensable in the medical field. In dentistry, metal is used for restorations, orthodontic wires, and dental implants. This article describes R&D on metallic biomaterials primarily conducted by the members of the Japan Institute of Metals. For more information, contact Mitsuo Niinomi, Toyohashi University of Technology, Department of Production Systems Engineering, 1-1 Hibarigaoka, Tempaku-cho.Toyohashi 441-8580, Japan     

燃料挥发性对柴油机性能及排放的影响

针对不同的发动机热状态及压缩比，试验研究了燃料物化特性对柴油机稳态及过渡工况下性能、排放的影响规律。应用自行开发的柴油机过渡工况控制系统及排气采集装置，模拟车用柴油机实际工作时的加速状态，对具有相同十六烷值但有不同挥发性能燃料的HC排放特性进行了研究，利用气相色谱仪对HC排放成分进行了分析。研究结果表明，采用挥发性好的燃料，可有效降低排气烟度，提高有效热效率，在发动机热状态不好及压缩比较低等燃烧条件恶劣、HC排放高的情况下，可有效地降低HC排放。