Increase of stress intensity near interface edge of elastic-creep Bi-material under a sustained load

The transition from small-scale creep to large-scale creep ahead of a crack tip or an interface edge with strong elastic stress singularity at the loading instant causes stress relaxation and the decrease of stress intensity in general. However, this study shows that the stress near the interface edge of bi-material with no or weak elastic stress singularity increases after the loading instant and brings about the stress concentration during the transition. In addition, the creep strain distribution of this bi-material after the loading instant is different from that occurred in the transition of an interface edge with strong elastic stress singularity or a crack tip (notch root). The criterion for the increase or decrease of stress intensity near the interface edge proved by the finite element method is proposed in this study. The stress intensity near the interface edge increases when the elastic stress singularity is lower than the creep stress singularity (λ^el < λ^cr) and vice versa.     

Microstructure Control of Sintered Porous Yttria-Stabilized Zirconia as a Durable Thermal Shielding Material

The microstructure of a thermal shielding material affects its thermal conductivity and mechanical property. In this study, the effects of the sintering temperature and the polymethyl methacrylate powder as a pore-former on the microstructure of a sintered porous yttria-stabilized zirconia (YSZ), which is used as a durable thermal shielding material, were investigated. It became clear that the microstructure of the sintered YSZ could be controlled by the particle size and the amount of the pore-former and the sintering temperature. The effect of the yttria amount in the YSZ on the microstructure was also clarified.     

Photoluminescence of Rare-Earth-Doped Ca-α-SiAlON Phosphors: Composition and Concentration Dependence

Rare-earth-doped Ca-α-SiAlON phosphors, with the compositions of (Ca_{1−3/2 x} RE _x ) _{m /2}Si_{12− m − n} Al _m+n O _n N_{16− n} (RE=Ce, Sm, and Dy, 0.5≤ m =2 n ≤3.0), were prepared by sintering at 1700°C for 2 h under 10 atm N₂. The concentration of rare earths varied from 3 to 30 at.% with respect to Ca. The photoluminescence (PL) properties were investigated as functions of the composition of the host matrix (i.e., m ) and the concentration of rare earths (i.e., x ). The results show that the emission properties can be optimized by tailoring m and x . The Ce³⁺ luminescence originating from the 4 f –5 d interconfigurational transitions is greatly affected by the environment surrounding the Ce³⁺ ions, which differs from the Sm³⁺ or Dy³⁺ luminescence arising from the 4 f –4 f intraconfigurational transitions. X-ray diffraction and scanning electron microscopy were used to explain the composition and concentration dependence of PL properties.     

Multiple‐valued immune network with apoptosis system

In this paper, we describe a new model of immune network based on biological immune response network. We propose an immunity like multiple‐valued network with apoptosis mechanism. The model is based on the interaction between B cells and T cells and the biological apoptosis mechanism in the human body. With the mechanism, a naturally immune system can be reproduced. The model is also applied to pattern recognition. It becomes possible with a conventional model to restrict the category increase of memory patterns. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 162(3): 51– 57, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20320     

Creation of Ferroelectric, Single-Crystal Architecture in Sm0.5La0.5BGeO5 Glass

Using a novel, selective heating by Nd:YAG laser, a single-crystal architecture is created in a model glass system, Sm_0.5La_0.5BGeO₅, which devitrifies congruently into a ferroelectric phase of the same composition as the parent glass. The Sm³⁺ ions in glass absorb the light and heat the matrix locally resulting in devitrification. Initially, a polycrystalline spot is formed. However, with optimum laser power, scanning speed, and the depth of focus, one of the grains acts as the seed for further growth as a single crystal. By programming the relative displacement of the glass with respect to laser spot, desired single ferroelectric crystal architecture is created. The optical functionalities (guiding of light and second harmonic generation) of the architectures are shown, which demonstrate the viability of this method for constructing active elements in optical integrated circuits. The single-crystal nature of the architecture is confirmed from the electron backscattered diffraction results.     

New bleeding model of additives in a polypropylene film under atmospheric pressure II

Many additives are commercially used to add more favorable qualities to films. The bleeding process by which the additive in a film comes to the surface is considered. A new bleeding model of additives in a polypropylene film under atmospheric pressure was investigated. Solubility and diffusion are found to be important for explaining this bleeding process. It was found that the experimental results were explained more precisely by assuming a two‐step transport process between the crystalline regions and the amorphous ones. The solubilities and diffusion coefficients of UV‐stabilizers such as 2‐(2H‐benzotriazol‐2‐yl)‐4‐(1,1,3,3‐tetramethylbutyl)phenol and 2‐(2H‐benzotriazol‐2‐yl)‐4‐methylphenol were determined at 40°C. The difference between the saturation solubilities and the diffusion coefficients of UV‐stabilizers was discussed by comparing with the results of molecular dynamics (MD) simulation. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Electrolytic removal of ammonia from brine wastewater: scale‐up,operation and pilot‐scale evaluation

Brine wastewater with a high ammonia content from an iodine processing plant (commonly called kansui in Japan) was treated by electrolysis. The system, which can be considered as an indirect electrolytic treatment process, generates chlorine at the anodes and initiates the formation of mixed oxidants like hypochlorous acid. The oxidants then act as agents for ammonia destruction. Laboratory‐scale experiments showed that high ammonia concentrations (as much as 200 mg dm^?3) could be completely removed within a few minutes, and could be considered a good alternative for efficient ammonia removal from saline wastewaters. From laboratory‐scale experiments in the batch and continuous modes, the charge dose was analyzed and used as the operating and scale‐up factor. The value of the charge dose was not severely affected by changes in operating conditions such as electrode spacing and temperature. The charge dose from batch and continuous runs was found to be in the range of 23 C (mg NH₄‐N removed)^?1 to 29 C (mg NH₄‐N removed)^?1. Using the charge dose obtained from laboratory‐scale continuous electrolysis experiments as the scale‐up factor, a pilot‐scale reactor was designed, and the operating conditions were calculated. In the pilot‐scale reactor tests at different flow rates, the effluent ammonia concentrations were reasonably close to the calculated values predicted from the charge dose equation. Copyright © 2004 Society of Chemical Industry     

Nondestructive inspection of thermal barrier coating of gas turbine high temperature components

A thermal barrier coating (TBC) is applied to high‐temperature components in gas turbines, and consists of a ceramic topcoat and a metallic bondcoat. Various kinds of TBC degradation and damage occur in high‐temperature components during service, such as topcoat thinning, topcoat delamination, and formation of a thermally grown oxide (TGO) layer below the topcoat, each of which can be examined using a suitable nondestructive inspection technique. Topcoat thinning can be detected by topcoat thickness measurement using terahertz waves, which are electromagnetic waves in the frequency region between optical and radio waves. The measurement resolution is about 10 μm, which is comparable to microscopic observation of the cross section in destructive inspection. Topcoat delamination can be detected by active thermography, in which the topcoat surface is scanned by a heating laser and the surface temperature distribution is measured by a thermal infrared camera. The combination of temperature peak and residual thermal image detection is effective in eliminating false detection. The TGO layer can be detected using photoluminescence, in which the Cr³⁺ ions included as an impurity in Al₂O₃ are detected. Since delamination tends to occur at locations at which the TGO layer has grown, TGO layer detection provides an effective method to select regions where delamination has occurred or is likely to occur. An inspection flow based on these techniques is proposed, which is expected to aid the establishment of condition‐based maintenance strategies of high‐temperature components. © 2016 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Comparison of particle-phase polycyclic aromatic hydrocarbons and their variability causes in the ambient air in Ho Chi Minh City, Vietnam and in Osaka, Japan, during 2005-2006

A comparative study of polycyclic aromatic hydrocarbons (PAHs) associated with particulate matter (TSP) in the ambient air in an urban area in Ho Chi Minh City, Vietnam and in Osaka, Japan was carried out from 2005 to 2006. The objective of this study was to investigate the environmental levels, emission sources, seasonal variations and health risk of eleven PAHs in the two cities, especially Ho Chi Minh City where air pollution is becoming a serious concern. The results showed that the concentrations of TSP and total PAHs were significantly higher in Ho Chi Minh City than levels in Osaka. The concentrations of 5- and 6-ring PAHs (BeP, BbF, BkF, BaP, BghiP and InP) were much higher in TSP samples in Ho Chi Minh City than in Osaka, accounting for 82% and 51% of total PAHs, respectively. These PAHs are known to be highly carcinogenic and mutagenic in humans. Vehicular emission is suggested as one of the main pollution sources of PAHs in both cities. Motorcycles and gasoline automobiles are suggested as the main emission sources of PAHs in Ho Chi Minh City, whereas diesel automobiles are the primary source in Osaka. Seasonal variations of PAHs were observed in this study; higher concentrations of PAHs were found in the rainy season (May-December) and lower concentrations corresponded to the dry season (February-April) in Ho Chi Minh City, while higher concentrations of PAHs were observed in the winter (November-January) in Osaka. The number of sunshine hours was an important meteorological factor affecting seasonal variations of PAHs in Ho Chi Minh City, while the temperature was a main factor causing the variations of PAHs in Osaka. The high BaP equivalent concentration of 5- and 6-ring PAHs even in the ambient air is an alarming signal for harmfulness to human health and environmental quality in Ho Chi Minh City.