Deformation and fracture of α-β brass two-phase bicrystals at 150 K

The deformation up to fracture at 150 K was undertaken on α-β brass two-phase bicrystals. The variation of the slip systems during the proceeding deformation was studied and explained on the basis of incompatible stresses. The normal stress-strain curves were analyzed for various types of bicrystals and the bending that appeared in the specimens when unloaded was explained with respect to the occurrence of the Bauschinger effect in the α phase. Fracture modes other than those observed at room temperature were present. The results, and other minor problems, were discussed.     

Radical polymerization of methyl methacrylate with some 1,2-disubstituted tetraphenylethanes as thermal iniferters

Summary The bulk polymerization of methyl methacrylate (MMA) with 1,2-disubstituted tetraphenylethanes, tetraphenylsuccinodinitrile (TPSN), tetra(p-methoxyphenyl)succinodinitrile (TMPSN), and pentaphenylethane (PPE), was investigated. These compounds were found to serve as thermal iniferters to induce living radical polymerization via a mechanism close to the model proposed previously (see Eq. 2). However, the living nature was not so high, because undesirable side reactions occurred. The oligomer with molecular weight of 2500 was isolated from the reaction mixture of MMA with TPSN, which was found to cause further polymerization of MMA. From the polymerization of styrene (St) with the polymers obtained by these iniferters, the block copolymers were produced.     

High-Temperature Active Oxidation of Chemically Vapor-Deposited Silicon Carbide in CO─CO2 Atmosphere

Active oxidation behavior of CVD-SiC in CO─CO₂ atmospheres was investigated using a thermogravimetric technique in the temperature range between 1823 and 1923 K. The gas pressure ratio, P _CO2/ P _CO, was controlled between 10⁻⁴ and 10⁻¹ at 0.1 MPa. Active oxidation rates (mass loss rates) showed maxima at a certain value of P _CO2/ P _CO, ( P _CO2/ P _CO )^*, In a P _CO2/ P _CO region lower than the ( P _CO2/ P _CO)^* a carbon layer was formed on the SiC surface. In a P _CO2/ P _CO region higher than the ( P _CO2/ P _CO)^*, silica particles or a porous silica layer was observed on the SiC surface.     

Leaching test of gamma-emitting Cs,Ru, Zr,and U from neutron-irradiated UO2/ZrO2 solid solutions in non-filtered surface seawater

The leaching behaviors of gamma-ray radionuclides, Cs-137, Ru-103, and Zr-95, produced by neutron irradiation of UO₂/ZrO₂ solid solutions, in real surface seawater were investigated under atmospheric conditions. The fraction of radionuclide inventory leached in the seawater was in the order of Cs > Ru (～U) ? Zr, indicating that the fraction was significantly affected by the chemical state of the radionuclides. However, the amount of soluble nuclides was proportional to that of uranium regardless of whether the solid solutions were prepared under an oxidative or reductive environment. A tiny fraction of Ru was filtered out by a 3 kDa nominal molecular weight cut-off filter after the 160 d leaching test, suggesting a different behavior from its ionic form, but Cs and U did not form a colloid-like species in seawater.     

Preparation and characterization of electroplated amorphous gold-nickel alloy film for electrical contact applications

A process for electroplating amorphous gold-nickel alloy with the atomic ratio of unity was developed. The plating bath was prepared by adding potassium cyanoaurate(I) into a known plating bath which produces amorphous nickel-tungsten alloy. At a sufficiently high gold concentration, the alloy deposit did not contain any tungsten. The amorphous nature of the Au-Ni alloy produced in the new bath was confirmed by using TEM and THEED. Hardness, resistivity, and contact resistance of this new alloy were determined, and the results are discussed for applications as an electrical contact material.     

日本彩色聚乙烯涂覆钢管的开发

试验了彩色聚乙烯涂覆钢管的耐腐蚀性和耐气候性，由于聚乙烯涂层隔绝水的作用，聚乙烯涂覆钢管具有优良的耐腐蚀性能，电阻绝缘值和优良的机械性能。建立了一个新的方式去研究分析聚乙烯抗老化剂消耗和在聚乙烯中的扩散。用有效测定的方法定量地预测彩色聚乙烯涂覆层的寿命，应用这些分析结果，不仅可使新的有色聚乙烯涂覆钢管在恶劣腐蚀环境介质情况下具有高的耐腐蚀性，而且有长的耐气候性。     

Single-crystal growth and characterization of Cu2O and CuO

We have prepared a large number of crystals of cuprous oxide (Cu2O) by various procedures. Photoluminescence spectra of these crystals were studied to examine the concentration of defects, especially copper vacancy VCu to seek favourable conditions for growing Cu2O crystal. High-quality single crystals of Cu2O were prepared by the floating-zone melting method in air. Several synthetic crystals (specimens FA, FZ and GZ) and also a natural crystal were studied by X-ray analysis, inductively coupled plasma spectroscopy analysis, optical absorption, photoluminescence, photoconductivity and cyclotron resonance absorption, photoluminescence, photoconductivity and cyclotron resonance absorption to characterize their optical and electrical qualities. The best values of mobility and scattering time of photocarriers at T = 4.2 K are estimated to be h1.8 × 105 cm2 V–1 s–1 and h60 ps for positive holes, and 1.3 × 105 cm2 V–1 s–1 and 70 ps for electrons in Cu2O. Further, we report preliminary experimental results on transport property of crystals also of cupric oxide (CuO) purified by the floating-zone melting method.     

Meshing curved wire‐frame models through energy minimization and packing of ellipses

In the initial phase of structural part design, wire‐frame models are sometimes used to represent the shapes of curved surfaces. Finite Element Analysis (FEA) of a curved surface requires a well shaped, graded mesh that smoothly interpolates the wire frame. This paper describes an algorithm that generates such a triangular mesh from a wire‐frame model in the following two steps: (1) construct a triangulated surface by minimizing the strain energy of the thin‐plate‐bending model, and (2) generate a mesh by the bubble meshing method on the projected plane and project it back onto the triangulated surface. Since the mesh elements are distorted by the projection, the algorithm generates an anisotropic mesh on the projected plane so that an isotropic mesh results from the final projection back onto the surface. Extensions of the technique to anisotropic meshing and quadrilateral meshing are also discussed. The algorithm can generate a well‐shaped, well‐graded mesh on a smooth curved surface. Copyright © 1999 John Wiley & Sons, Ltd.     

Dominant stress region for crack initiation at interface edge of microdot on a substrate

In order to examine the mechanics of crack initiation at the free interface edge of a microcomponent on a substrate, delamination tests are carried out for two specimen shapes of Cr microdots on a SiO₂ substrate. The microdots of the first specimen are shaped like the frustum of a round cone. The Cr microdots are successfully delaminated from the SiO₂ substrate in a brittle manner and the critical load is measured by atomic force microscopy (AFM) with a lateral loading apparatus. Stress analysis reveals that a singular stress field exists near the interface edge and the strength for the crack initiation is governed by the intensified normal stress field. The critical stress intensity parameter is evaluated as K_σC ≈ 0.24 MPa m^0.39. Similar delamination tests are conducted for microdots shaped like the frustum of an oval cone. The stress distributions at the crack initiation of this specimen shape show a higher normal stress than the first specimen shape in the region near the interface edge of about x < 40 nm, while it is lower in the region of about x > 50 nm (x: distance from the edge). This suggests a limitation of conventional fracture mechanics: namely, the crack initiation in these specimens is not uniquely governed by the intensity of the singular field. It is found that the delamination crack is initiated when the averaged stress σ_ya in the region of 90-130 nm reaches 190-270 MPa, regardless of the specimen shape. This indicates that the dominant stress region of crack initiation is roughly estimated as 90-130 nm and the criterion is given in terms of the averaged stress in the region.