New balance ground relay for parallel four-circuit transmission lines

A 66-kV network generally is grounded through a neutral grounding resistor. In this network a single-phase ground-fault current is limited to as small as 100 to 400 A. There are parallel four-circuit transmission lines mounted on the same tower in the 66-kV network. In such transmission lines, the load and the fault currents could induce circulating current that flows through the lines. Since the circulating current has zero-phase-sequence and negative-phase-sequence components, it could cause unwanted operation of a balance ground relay using zero-phase-sequence current. However, it is difficult to compensate for the circulating current by the conventional vector compensation scheme. This paper presents a new balance ground relay to deal with the circulating current. In the relay from the ground-fault inception until first tripping, the difference current Δ3I_2d of negative-phase-sequence current 3I_2d of the differential current between two protected lines is used as an input current. The Δ3I_2d is the difference current of 3I_2d between, before and during faults. After the first tripping, the difference current of positive-phase-sequence load current and zero-phase-sequence current of the forementioned differential current are used as an input current. Consequently, a higher sensitivity of the ground-fault protection for these lines has been achieved. The correct operation of the new balance ground relay was confirmed when a single-phase-ground-fault occurred in the parallel four-circuit transmission lines, to which the relay is applied.     

Air vent in water chamber and surface coating on liner slides concerning auxiliary cooling system for the high temperature engineering test reactor

Experimental study was made to confirm the validity of new designs of the auxiliary cooling system for the high temperature engineering test reactor (HTTR). First, it is necessary to vent residence air in outlet side of water chamber of the auxiliary heat exchanger for the HTTR. Accordingly, we have proposed to mount a proper bend duct in the outlet side of the water chamber. Air vent is done by difference between pressures at both ends of the bend duct caused by the forced water circulation using the water pumps. From flow tests, it was confirmed that it is capable of venting the air through the bend duct by circulating the water in maximum capacity of the water pumps. Second, it is essential to prevent seizure and excessive wear of the liner slides of the auxiliary concentric hot gas duct for the HTTR at a service temperature of 950°C. Therefore, we have put forward to coat titanium nitride (TiN) on the surface of the liner slides made of nickel-based superalloy Hastelloy XR using the thermochemical vapor deposition method. As a result of seizure and wear tests, it was confirmed that the TiN coating film of 3 μm on the surface of Hastelloy XR is sufficient.     

Boron removal by titanium addition in solidification refining of silicon with Si-Al melt

In order to effectively remove B from Si for its use in solar cells, a process involving B removal by solidification refining of Si using a Si-Al melt with Ti addition was investigated. For clarifying the effect of Ti addition on B removal from the Si-Al melt, TiB₂ solubilities in Si-64.6 at. pct Al melt at 1173 K and Si-60.0 at. pct Al melt at 1273 K were determined by measuring the equilibrium concentrations of B and Ti in the presence of TiB₂ precipitates. The small solubilities of TiB₂ in the Si-Al melt indicate the effective removal of B from the Si-Al melt by Ti addition. Further, solidification experiments of Si-Al alloys containing B by Ti addition were performed, and the effect of Ti addition on the solidification refining of Si with the Si-Al melt was successfully confirmed.     

Solution synthesis of crystallized AMO4 (A=Ba, Sr, Ca; M=W, Mo) film at room temperature

A well-crystallized AMO₄ (A=Ba, Ca, Sr; M=W, Mo) films have been prepared at room temperature through a simple solution reaction in respective alkaline solution at higher pH ranging from 12–14. Adopting the corrosion principle for oxidation of metal substrate, these double oxide films were carried out in presence of chemical driving force without any special apparatus or devices. Hydrogen peroxide was used to enhance the dissolution rate of metal substrates. The driving force for the film formation and growth were high concentration of A²⁺, MO₄²⁻ ions with high pH conditions. Average grain sizes of 8–10 μm with bipyramidal shaped particle were grown to the thickness of about 10–14 μm after 3–6 hours treatment. The crystallization of AMO₄ was characterized by three-dimensional nucleation. This work demonstrates the possibility of fabrication of functional ceramic films directly from the aqueous solution in a single step by solution reactions.     

The gamma-ray-induced crosslinking of polyacrylamide

The gamma-ray-induced crosslinking of polyacrylamide was carried out under various conditions. The molecular weight of the polymer before inrradiation was found to be the most important factor for crosslinking. When polymers have low molecular weights such as 80,000, the intensity of radiation, the external pressure applied, and the water content of the polymer powder became important for crosslinking. Although the polycrylamide hydrogel can be obtained directly by irradiating the monomer, it was obtained more conveniently by the irradiation of monomer—polymer mixtures. The hydrogels obtained by the radiation with a dose of over 50 kgray, absorb water by 1000–1500 wt %.     

Analysis of XANES for identification of highly dispersed transition metal oxides on supports

XANES of vanadium and niobium oxide on silica or alumina have been analyzed quantitatively by a deconvolution technique. Based on the results for reference compounds, local structures of supported vanadium and niobium species were identified. The composition was estimated from difference spectra for the samples which consisted of two kinds of species.     

Inhibitory effect of lead on the proliferation of cultured vascular endothelial cells

We investigated the effect of lead nitrate (0.5, 1.0, 2.0 or 5.0 microM) on the proliferation of cultured bovine aortic endothelial cells. After exposure to lead, the number of cells and the incorporation of [3H]thymidine into the acid-insoluble fraction of the cells were reduced in parallel in a concentration-dependent manner. Histologically, lead treatment resulted in a decrease in the cell number accompanied by a change in the cell shape from polygonal to spindle; however, no degenerative change was observed except in 5.0 microM lead-treated cells. Furthermore, stimulation of [3H]thymidine incorporation by either basic or acidic fibroblast growth factor was significantly reduced by lead. However, the leakage of lactate dehydrogenase into the medium from the cells, a marker of nonspecific cell damage, was not changed by lead. From these results, it was revealed that lead inhibits the proliferation of cultured vascular endothelial cells without nonspecific cell damage. Although lead does not destroy the monolayer of endothelial cells, the metal may exhibit its noxious effect in the repair process of the vascular endothelium.     

Studies on chitin 3—effect of coagulants and annealing on the preparation and the properties of chitin membrane

Chitin membrane was prepared by casting a N,N-dimethyl acetamide, N-methyl 2-pyrrolidone and lithium chloride (DMA-NMP-LiCl)solution of chitin and coagulating with several media. The effect of the coagulants on membrane formation was studied. 2-Propanol was found to be more favourable than methanol, ethanol, acetone and mixtures of 2-propanol and water. The membrane obtained in 2-propanol was subjected to annealing. Annealing made the membrane dense and strong. The tensile strength of the membrane annealed at 145°C for 2hr was about twice that of an unannealed membrane. The solute permeability of the annealed membranes was lower than that of the original one. These phenomena could be clearly interpreted in terms of crystallinity.     

Change of characteristics of desulfurization and denitrification by combustion flue gas composition and electrode configuration under pulsed corona discharge

Laboratory-scale and parametric experiments of SO₂ and NO_x removal from the simulated combustion gas by pulsed corona discharge have been performed by changing the combustion gas composition and temperature, the electrode configuration of plasma reactor, and the polarity of high-voltage electrode. The following results are obtained: 1) the higher the concentration of H₂O and O₂, the higher the efficiency of desulfurization and denitrification at the same specific input; 2) the pulsed corona discharge with a voltage pulsewidth as short as 200 ns of negative polarity shows the possibility to attain almost 90 percent deSO_x and deNO_x efficiency at the specific discharge input of 20 J/g, which is almost the same as the specific input in the electron-beam process; 3) the deNO_x characteristics show a little temperature dependence in the range of 70 to 130°C, but the deSO_x efficiency increases rapidly in the temperature region below 100°C suggesting the thermochemical dependence of deSO_x reaction; 4) when desulfurization and denitrification proceed, the white dendritic powder deposits on the plasma reactor whose composition is identified to be 49 mol% (NH₄)₂SO₄ and 47 mol% of 2NH₄NO₃ · (NH₄)₂SO₄, and the ratio of SO₂, NO and NH₃ of the deposit is almost equal to that of supplied gas.     

TRVs and fault clearing stresses in extra-high-voltage radial networks

To cope with the high rate of increase of power demand in the main industrialized districts in Japan, 550-kV transmission systems covering the districts have been reinforced, with most of the main power plants connected directly to these systems. Through 550-/300-kV substations, the majority of power to the districts is supplied by 300-kV systems. To limit the excess short-circuit capacity in the 300-kV systems, they tend to be reconstructed as so-called radial networks. In radial networks with high short-circuit capacity and relatively small number of transmission lines connected to the substation busbars, the rate of rise of TRV can be far higher than standard value. This paper analyzes the transient recovery voltages (TRV) in such extra-high-voltage radial networks in Japan, together with the relevant stresses to circuit-breakers during fault clearings. Future system conditions have also been introduced. As the typical rate of rise of the TRV values, more than twice that of today's standard ones are probable.