Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

Fabrication of blue-light emission fused-silica substrates by using Si-ion implantation and high-temperature annealing

We fabricated fused-silica substrates which emit blue light by using Si-ion implantation and high-temperature annealing. Photoluminescence peak wavelengths are around 400 nm, and the peak intensities can be remarkable after annealing above 1150 °C.     

Twin-Related Tetragonal Variants in Yttria Partially Stabilized Zirconia

Crystals of yttria partially stabilized zirconia were grown by the arc-image floating-zone technique and studied by transmission electron microscopy. Crystals annealed at 1700°C consist of tetragonal precipitates and a cubic matrix. The platelike domains in a precipitate are twin-related tetragonal variants stacked alternately parallel to the (011) twin plane. The axial relations between the tetragonal precipitate and the cubic matrix are [100]_tetragonal|[100]_cubic, [011]_tetragonal|[011]_cubic.     

Reverse osmosis separation of hydrocarbons in aqueous solutions using porous cellulose acetate membranes

A physicochemical parameter, represented by the symbol Σs^*, based on molar solubility in water and molar attraction constants of Small, has been developed to express quantitatively the relative hydrophobicity, or nonpolar character, of the hydrocarbon molecule. The value of Σs^* can be calculated for a hydrocarbon from its chemical structure. The scale of Σs^* is consistent within each group of aromatic, cyclic, and noncyclic hydrocarbons. Reverse osmosis data have been obtained at 250 psig for single-solute aqueous feed solution systems involving low concentrations of 39 different hydrocarbons (including 13 aromatics, 10 cyclic, and 16 noncyclic compounds) and several samples of cellulose acetate membranes of different surface porosities. The effect of operating pressure on membrane performance has also been studied for two aromatic hydrocarbon solutes. The values of Σs^* for the solutes used were in the range of 425 to 924 for aromatic hydrocarbons, 521 to 931 for cyclic hydrocarbons, and 369 to 960 for noncyclic hydrocarbons. The reverse osmosis data have been correlated with Σs^* for each group of hydrocarbons studied. In all cases, positive solute separations were obtained, and the ratio [PR]/[PWP] was less than 1. With respect to each film, solute separation increased with increase in Σs^*, and decreased with increase in operating pressure. Also, solute separation decreased in the order aromatic hydrocarbon > cyclic hydrocarbon > noncyclic hydrocarbon at any given value of Σs^*. At a given operating pressure, for low values of Σs^* (～500 or less) solute separation increased with progressive decrease in average pore size on the membrane surface. For high values of Σs^* (～800 or more), solute separation initially increased with decrease in average pore size, then passed through a maximum and minimum with further decrease in average pore size, and again increased with still further decrease in average pore size. The results are discussed on the basis of preferential sorption of solute at the membrane–solution interface under the experimental conditions studied.     

Reverse osmosis separations of polyethylene glycols in dilute aqueous solutions using porous cellulose acetate membranes

Reverse osmosis separations of eight polyethylene glycol (PEG) solutes in the average molecular weight range of 200 to 6750 in single-solute dilute aqueous solutions have been studied using porous cellulose acetate membranes at the operating pressures of 50, 75, and 100 psig. Diffusivity data for the above PEG solutes have also been obtained from experimental data on intrinsic viscosities. From an analysis of all experimental data, numerical values for the parameters representing the polar (?ΔΔG/RT), steric (δ^*ΣE_s), and nonpolar (ω^*Σs^*) forces governing reverse osmosis separations of PEG solutes have been generated. These numerical values are useful for precise characterization of cellulose acetate membranes for whose specifications sodium chloride is not the appropriate reference solute because of its low or practically negligible separation under reverse osmosis operating conditions. This work also illustrates that solute separation in reverse osmosis can predictably increase or decrease with increase in operating pressure depending on experimental conditions.     

Hydrophobic effects on protein/nucleic acid interaction: enhancement of substrate binding by mutating tyrosine 45 to tryptophan in ribonuclease Tl

Hydrophobic effects on binding of ribonuclease Tl to guaninebases of several ribonucleotides have been proved by mutatinga hydrophobic residue at the recognition site and by measuringthe effect on binding. Mutation of a hydrophobic surface residueto a more hydrophobic residue (Tyr45 – Trp) enhances thebinding to ribonucleotides, including mononucleotide inhibitorand product, and a synthetic substrate-analog trinudeotide aswell as the binding to dinucleotide substrates and RNA. Enhancementson binding to non-substrate ribonucleotides by the mutationhave been observed with free energy changes ranging from –2.2 to – 3 .9 kJ/mol. These changes are in good agreementwith that of substrate binding, –2.3 kJ/mol, which iscalculated from Michaelis constants obtained from kinetic studies.It is shown, by comparing the observed and calculated changesin binding free energy with differences in the observed transferfree energy changes of the amino acid side chains from organicsolvents to water, that the enhancement observed on guaninebinding comes from the difference in the hydrophobic effectsof the side chains of tyrosine and tryptophan. Furthermore,a linear relationship between nucleolytic activities and hydrophobicityof the residues (Ala, Phe, Tyr, Trp) at position 45 is observed.The mutation could not change substantially the base specificityof RNase Tl, which exhibits a prime requirement for guaninebases of substrates.     

Hydrothermal Formation of Hydroxyapatite Layers on the Surface of Type-A Zeolite

Type-A zeolite evenly covered with hydroxyapatite thin layers was prepared using hydrothermal treatment at 120°C for 8 h under autogenous pressure. The hydroxyapatite needlelike nanocrystals, 100–200 nm in diameter and 30 nm in thickness, were grown under the reaction between discharged Ca²⁺ ions from type-A zeolite and PO₄³⁻ ions in (NH₄)₃PO₄ solution. The preferential orientations of the c -axis of hydroxyapatite crystals perpendicular to a zeolite surface were observed using transmission electron microscopy. The crystal structure of type-A zeolite was not destroyed under the reaction, but the surface morphology was changed only with complete covering of scaly hydroxyapatite particles.     

A coaxial pulsed plasma thruster using chemical propellants

Pulsed plasma thrusters (PPTs) have the advantages of mechanical simplicity and robustness compared to other electric propulsion systems. However the thrust power ratio of PPTs is lower than that of other electric propulsion systems. To enhance the thrust performance of the PPT, we propose to use several combustible solid chemicals as coaxial PPT propellants to replace Teflon^® (Polytetrafluoroethylene: PTFE). With the design, the force obtained thermodynamically is expected to augment the PPT thrust power ratio with the help of the chemical energy contained in the propellants. As a result, the thrust power ratio is increased using hydroxyl-terminated polybutadiene-ammonium perchlorate (HTPB-AP)-based propellants compared to the case of ordinary Teflon. The discharge current and voltage waveform does not change even when the propellant is changed. These findings could indicate that the impulse bits by gasdynamic contribution are lager in the case of chemical solid propellants than in the case of Teflon.