Development of new‐type outdoor termination using composite insulator with SF6 gas: Commercial use for 77‐kV transmission lines and development for 154‐kV XLPE cable

Recently, composite insulators have been increasingly employed mainly for economic reasons. We have developed a new type of outdoor termination using a composite insulator, which can be installed horizontally on a steel tower in order to reduce the construction cost. In this outdoor termination, SF₆ gas is filled in the composite insulator and a cold shrinkable premolded rubber unit is applied instead of the combined use of a rubber‐molded stress relief cone, epoxy resin insulator and spring unit. The application of the composite insulator, SF₆ gas and cold shrinkable premolded rubber unit reduces the total weight and makes it possible to install the termination horizontally on the tower. The new‐type outdoor termination for 77‐kV XLPE cable has already been applied in commercial use and enabled a reduction of the construction costs for power transmission lines. A 154‐kV new‐type outdoor termination has been developed and its initial electrical tests were successfully completed. This paper describes the design and performance of both 77‐kV and 154‐kV new‐type outdoor termination, and a follow‐up survey of the 77‐kV new termination in a commercial use. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 159(4): 18– 26, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20511     

Comparison of enteral nutrition with combined enteral and parenteral nutrition in post-pancreaticoduodenectomy patients: a pilot study

Background  

Many clinical studies have demonstrated that early postoperative enteral nutrition (EN) improved the postroperative course. Post-pancreaticoduodenectomy (PD), patients tend to suffer from postoperative nausea, abdominal distention, and diarrhoea, causing difficulty in the introduction of EN. In this pilot study, we investigated the appropriate nutritional mode post-pancreatic surgery.     

TEM,XPS and SIMS Analyzes on Grain Boundary of Lanthanum Chromites

The morphological characteristics, chromium valence state, and cation transport in the vicinity of grain boundary in La_1-xCa_xCrO₃ were investigated by using TEM/EDS, XPS and SIMS techniques. The width of grain boundary was around 1 nm where anomalous enrichment of calcium was observed. Higher valence state of chromium such as Cr⁶⁺(d⁰) was detected in the grain boundaries whereas Cr³⁺(d³) and Cr⁴⁺(d²) were dominant in the bulk. Very fast interdiffusion of alkaline earths was observed in the Sr²⁺-La_0.75Ca_0.25CrO₃ system. All observed phenomena were correlated by assuming the A-site vacancy which may be induced by the formation of Cr⁶⁺ at grain boundaries.     

Ordered Mesoporous Silica Derived from Layered Silicates

Here, the development of ordered mesoporous silica prepared by the reaction of layered silicates with organoammonium surfactants is reviewed. The specific features of mesoporous silica are discussed with relation to the probable formation mechanisms. The recent understanding of the unusual structural changes from the 2D structure to periodic 3D mesostructures is presented. The formation of mesophase silicates from layered silicates with single silicate sheets depends on combined factors including the reactivity of layered silicates, the presence of layered intermediates, the variation of the silicate sheets, and the assemblies of surfactant molecules in the interlayer spaces. FSM‐16‐type (p6mm) mesoporous silica is formed via layered intermediates composed of fragmented silicate sheets and alkyltrimethylammonium (C_nTMA) cations. KSW‐2‐type (c2mm) mesoporous silica can be prepared through the bending of the individual silicate sheets with intralayer and interlayer condensation. Although the structure of the silicate sheets changes during the reactions with C_nTMA cations in a complex manner, the structural units caused by kanemite in the frameworks are retained. Recent development of the structural design in the silicate framework is very important for obtaining KSW‐2‐based mesoporous silica with molecularly ordered frameworks. The structural units originating from layered silicates are chemically designed and structurally stabilized by direct silylation of as‐synthesized KSW‐2. Some proposed applications using these mesoporous silica are also summarized with some remarks on the uniqueness of the use of layered silicates by comparison with MCM‐type mesoporous silica.     

Parallel processing of network calculations in order to speed up transient stability analysis

Power systems have become very large, and in addition the forthcoming open electricity market will make power system operation more complex. Therefore, power system operation must become more efficient and flexible. Very fast power system simulation is a means of achieving more sophisticated power system on‐line monitoring and control, and parallel computing is a key technology for very fast power system simulation. This paper proposes an efficient and fast parallel network calculation algorithm that will contribute to the development of fast power system simulation programs. Numerical examples show that the proposed method using six processors is about 4.0 times as fast as the usual serial algorithm when applied to a large‐scale radial power system and about 3.2 times as fast when applied to a large‐scale loop power system. © 2001 Scripta Technica, Electr Eng Jpn, 135(3): 26–36, 2001     

Remote sensing system for spatial electric field strength using free space light transmission

Most of the breakdowns in an electric power system are caused by lightning to the tower used for high‐voltage transmission wires. To avoid accidents due to lightning, it would be desirable to develop a measurement system for the spatial electric field distribution around the tower. We have developed a new system that can measure the electric field around the steel tower for electric power transmission by using an optical electric sensor. In conventional methods, the sensor is generally illuminated by light transmitted by optical fibers. On the other hand, the new measurement system illuminates the Pockels sensor directly by using a laser to measure the far electric field. Furthermore, our newly proposed feedback system makes it possible to measure the spatial electric field without concern for the change of Pockels sensor's operation point influenced by temperature change. This system is applicable as a remote sensing system to monitor the spatial electric field around a high‐voltage transmission line. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 162(2): 10–19, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20552     

A 250-Mb/s/pin, 1-Gb double-data-rate SDRAM with a bidirectionaldelay and an interbank shared redundancy scheme

This paper describes three circuit technologies indispensable for high-bandwidth multibank DRAM's. (1) A clock generator based on a bidirectional delay (BDD) eliminates the output skew. The BDD measures the cycle time as the quantity charged or discharged of an analog quantity, and replicates it in the next cycle. This achieves a 0.18-mm ², two-cycle-lock clock generator operating from 25 to 167 MHz with a 30-ps resolution. (2) A quad-coupled receiver eliminates the internal skew caused by the difference between a rise input and a fall input by 40%. (3) An interbank shared redundancy scheme (ISR) with a variable unit redundancy (VUR) efficiently increases yield in multibank DRAM's. The ISR allows redundancy match circuits to be shared with two or more banks. The VUR allows the number of units replaced to be variable. These circuit technologies achieved a 250-Mb/s/pin, 8-bank, 1-Gb double-data-rate synchronous DRAM