Oxidative coupling of methane over Na+-ZrO2-C1-/Al2O3 catalysts

Oxidative coupling of methane (OCM) was carried out over Na⁺-ZrO₂-Cl /A1[₂O₃ catalysts in a temperature range from 1023 to 1123 K. The catalysts were prepared by impregnating the α- or γ-Al₂O₃ supports with sodium carbonate and/or zirconyl chloride. The OCM activity was examined using the catalysts prepared by three different preparation procedures. The best catalyst was the one prepared by subsequent impregnation of sodium carbonate-preimpregnated γ-Al₂O₃ with a mixed solution of sodium carbonate and zirconyl chloride. It was found that preimpregnated sodium played an important role in reducing the combustion activity of the γ-Al₂O₃. The catalyst with an optimal composition showed the highest C₂ selectivity and yield of 40.8% and 15.1%, respectively. From the X-ray diffraction analysis it was found that tetragonal ZrO₂ was formed and that NaCl existed in the catalysts with relatively high sodium contents.     

Experimental analysis of bubble mode in a plate-type absorber

An experimental analysis of ammonia-water absorption was performed in a plate-type absorber. The flow of water and ammonia gas was performed in the bubble mode. The experiments were made to examine the effects of solution flow rate and gas flow rate on the performance of the absorber. It was found that the increase of solution flow rate rarely affected the mass transfer, but improved the heat transfer. As the gas flow rate increased, slugging occurred in the bubble mode and influenced the thermal boundary layer. Finally, the results were converted into dimensionless numbers to elucidate physical phenomena and plotted as Sherwood number versus Reynolds number for mass transfer performance and Nusselt number versus Reynolds number for heat transfer performance.     

Durable antimicrobial treatment of cotton fabrics using N‐(2‐hydroxy)propyl‐3‐trimethylammonium chitosan chloride and polycarboxylic acids

N‐(2‐hydroxy)propyl‐3‐trimethylammonium chitosan chloride (HTCC), a water‐soluble chitosan quaternary ammonium derivative, was used as an antimicrobial agent for cotton fabrics. HTCC has a lower minimum inhibition concentration (MIC) against Staphylococcus aureus, Klebsiella pneumoniae, and Escherichia coli compared to that of chitosan; however, the imparted antimicrobial activity is lost on laundering. Thus crosslinking agents were utilized to obtain a durable antimicrobial treatment by immobilizing HTCC. Several crosslinkers such as dimethyloldihydroxyethylene urea (DMDHEU), butanetetracarboxylic acid (BTCA), and citric acid (CA) were used with HTCC to improve the laundering durability of HTCC treatment by covalent bond formation between the crosslinker, HTCC and cellulose. The polycarboxylic acid treatment was superior to the DMDHEU treatment in terms of prolonged antimicrobial activity of the treated cotton after successive laundering. Also, the cotton treated with HTCC and BTCA showed improved durable press properties without excessive deterioration in mechanical strength or whiteness when compared to the citric acid treatment. With the addition of only 0.1% HTCC to BTCA solutions, the treated fabrics showed durable antimicrobial activity up to 20 laundering cycles. The wrinkle recovery angle and strength retention of the treated fabrics were not adversely affected with the addition of HTCC. Therefore, BTCA can be used with HTCC in one bath to impart durability of antimicrobial activity along with durable press properties to cotton fabric. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1567–1572, 2003     

Effects of rosemary extracts and major constituents on lipid oxidation and soybean lipoxygenase activity

Rosemary (Rosemarinus officinalis L.) leaves were extracted with three different solvents, namely hexane, acetone and methanol. A reverse-phase high-performance liquid chromatography system in combination with a mass detector was used to quantitate the content of carnosol, carnosic acid and ursolic acid in the rosemary extracts. All rosemary extracts showed strong inhibitory effects on lipid oxidation and soybean lipoxygenase activity.     

Continuous ethanol production from wood hydrolysate by chemostat and total cell retention culture

Chemostat and total cell retention cultures with internal filter system ofSaecharomyc.es cerevisiae H1-7 were carried out to produce ethanol from wood hydrolysate. Maximum ethanol productivity obtained in a chemostat with the aeration rate of 1 vvm was 3.79 g/(L·h). This was 20% higher than that in a chemostat without aeration. However, the substrate was not completely consumed at the dilution rate with the maximum productivity. The realistic productivity, which has higher than 99% conversion rate of substrate, was. 2.95 g/(L·h). The maximum productivity in the total cell retention culture was 6.65 g/(L·h) at the dilution rate of 0.19 h¹ and the residual glucose concentration was negligible.     

Preparation of porous thin films of a partially aliphatic polyimide

A thermally labile polymer, poly(propylene glycol), was modified to obtain PPG having an amino end group. PPG was incorporated into a partially aliphatic polyimide based on an alicyclic dianhydride, and this afforded triblock copolymers containing various amounts of PPG blocks. The thermal properties of the copolymers were investigated by thermogravimetric analysis and differential scanning calorimetry. The thermal decomposition of the PPG block in the copolymers was carried out at 240°C under various pressures to obtain porous polyimide films. The pores remained during the thermolysis under a reduced pressure of 710 mmHg, whereas they collapsed under (near) atmospheric pressure. The pore size increased as the amount of the PPG block in the copolymers increased. The dielectric constants of the porous polyimides varied from 2.60 to 2.42 with the original copolymer composition. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 532–538, 2006     

The Torque Transmission Capabilities of the Adhesively-Bonded Tubular Single Lap Joint and the Double Lap Joint

With the wide application of fiber-reinforced composite materials in aircraft, space structures and robot arms, the design and manufacture of composite joints have become a very important research area because they are often the weakest areas in composite structures.

In this paper, the stress and torque transmission capabilities of the adhesively-bonded tubular single lap joint and the double lap joint were experimentally tested. In order to compare the experimental results with the calculated results, the stress and torque transmission capabilities were analyzed by the 3-dimensional finite element method taking into consideration the nonlinear properties of the adhesive.

From the experiments it was found that the torque transmission capabilities of the adhesively-bonded double lap joint was 2.7 times as large as that of the single lap joint. Also, it was found that the fatigue limit of the double lap joint was 16 times as large as that of the single lap joint.     

Effect of low-cycle fatigue on the hot ductility of plain carbon steel

In a continuous casting steelmaking operation, the surface of a slab is under a condition that can be characterized as high-temperature, low-cycle fatigue in which the tensile and compressive stress is repeatedly developed. For this reason, for the evaluation of the hot ductility of a slab, considering the fatigue deformation is more feasible before a tensile or compressive test. In this study, the effects of low-cycle fatigue on the hot ductility of steels with a carbon content of 0.06–0.8 wt.% are investigated at various temperatures. For a carbon content of 0.06%, there were no significant differences between the RA values from a simple tensile test and those from a tensile test after fatigue deformation. The tendency of ductility deterioration with fatigue deformation is evident in 0.1 %C steel, and is due to the deformation-induced ferrite film that forms around the prior austenite grain. Conversely, high carbon steel containing 0.8 %C did not show a recovery of hot ductility in a low temperature region, and the specimen on which the tensile was measured after fatigue showed a higher hot ductility in the low temperature region, which is thought to result from the pearlite refinement effects. As the results obtained in this work showed noticeable differences in the hot ductility of carbon steel through the test conditions, it is suggested that for more accurate data, fatigue deformation be adopted in which the temperature range in an unbending operation is determined in the steelmaking factory.     

Effects of anodizing voltage on the anodized and hydrothermally treated titanium surface

Anodic oxidation is the process of creating a titanium oxide layer with various defects more dense and stable. In this study, a dense, stable and porous oxide layer was formed using anodic spark oxidation on pure titanium surface and hydroxyapatite crystals were formed on its surface via a hydrothermal treatment. A mixture of 0.02M−GP (Glycerolphosphate disodium salt) and 0.2M-CA (Calcium acetate) was used as an electrolyte. By increasing the anodizing voltage to 220, 260, 300, and 360 V, the effects of the anodizing voltage were examined by evaluating the film properties after anodization and a hydrothermal treatment. Breakdown occurred around 230 V. As the voltage increased after breakdown, the pore size increased. After the hydrothermal treatment, the amount of HA crystal precipitation was also increased as the voltage increased. The mean surface roughness (Ra) of the anodizing surface was also increased as the voltage increased. The Ra value was larger in the hydrothermally treated group compared with the group treated with anodization as a result of the HA crystals present on the surface after the hydrothermal treatment. Corrosion resistance of the surface modified by anodization was significantly increased in a saline solution compared to that for the non-treated group; this increased further after the hydrothermal treatment. These increases were most likely due to a thick stable oxide layer formed through anodization. Thus, it is believed that titanium with its surface modified through anodic spark oxidation would be a suitable biomaterial due to its corrosion resistance and biocompatibility.     

Simulations of the dielectric constant of bonding materials and field emission properties of CNT cathodes

The effect of the dielectric constant (k) of bonding materials in a screen-printed carbon nanotube (CNT) cathode on the field enhancement factor was investigated for high-efficiency CNT cathodes using the ANSYS software. The values obtained by a simulation study were compared to the experimental results obtained for screen-printed CNT cathodes. The field enhancement factor increased as the dielectric constant decreased, reaching a maximum value at a dielectric constant of 1, the value for a vacuum. The findings indicate that the larger sheet resistance of the bonding materials, after the firing process, can be attributed to the larger emission current of the CNT cathode. From these results, it was concluded that the best bonding materials for screen-printed CNT cathodes should have a low dielectric constant and a high sheet resistance. This finding can be used as criteria for selecting bonding materials for use in CNT pastes for highly efficient CNT cathodes.