Influence of activated carbon pore structure on oxygen reduction at catalyst layers supported on rotating disk electrodes

Carbon materials are often used as catalyst supports, and for catalysts in electrodes of a polymer electrolyte fuel cell, carbon black has been used. Recently, it was found, however, that activated carbon could replace carbon black and besides, significantly improve the activity of the electrode catalyst layer for oxygen reduction. In the present study, to optimize the pore structure of activated carbon for further activity improvement, the influence of the pore structure on the activity was investigated using activated carbon of various specific surface areas and mean pore diameters. A catalyst layer was formed from activated carbon loaded with platinum and a polymer electrolyte. The activity of the layer was measured in an oxygen-saturated perchloric acid solution, supporting the layer on a rotating glassy carbon disk electrode. We found that increases in the specific surface area and mean pore diameter increased the activity and that the latter was more effective than the former mainly due to the enhanced mass-transfer in the pores; the catalyst layer formed from activated carbon with the largest mean pore diameter was the most active. Unless pores excessively develop and lose connections between particles, a large pore diameter is therefore desired for the fuel cell electrodes.     

Elevated temperature instrumented Charpy impact of a sintered silicon carbide

A commercially available, densely sintered alpha silicon carbide was tested in air from room temperature to 1700°C using a modified instrumented pendulum unit and standard Charpy size test specimens. The resistance heated silicon carbide specimens exhibited only elastic behavior, even at 1700°C. A compliance analysis of the test revealed a linear elastic decrease of the absorbed impact energy and also a decrease of the fracture stress of the silicon carbide with increasing temperature.     

Lysozyme requires fluctuation of the active site for the manifestation of activity

Mutations around His15 which lie far away from the active site,stimulated glycol chitin activity of lysozyme at physiologicaltemperature. Del-Argl4Hisl5 lysozyme, a mutant lysozyme whoseArgl4 and Hisl5 were deleted together, and has the highest activityamong these mutant lysozymes, had a similar binding abilityto a trimer of N-acetyl-glucosamine, a substrate analogue, relativeto native lysozyme. This suggests that the increased activitywas due to an increased k_cat in the catalysis reaction. TheH-D exchange rate of the N-1 proton in the Trp63 which is locatedin the active site cleft, was enhanced in the Del-Argl4Hisl5lysozyme, while 2-D proton NMR analysis revealed no conformationalchange around Trp63. We conclude that some sort of fluctuationat the active site might be required for the manifestation ofactivity. This theory is supported by the finding that the Del-Argl4Hisl5lysozyme showed a shift in temperature dependency of activityto lower temperatures compared with that of native lysozyme.     

Preparation of Porous Ceramics with Calcium Metaphosphate Fiber Skeleton for Biomedical Use

High-strength calcium metaphosphate fibers for biomedical applications are extracted from crystallized products of calcium ultraphosphate glasses by aqueous leaching. In the present work, new types of porous ceramics with a skeleton composed of the crystalline fibers are prepared by heating the fibrous products extracted. The fibers in the ceramic are interlinked to each other by glassy phases formed during the heating. This porous material has a large porosity of >60%. The surface of the skeleton can be successfully converted into new calcium phosphate phases such as apatite by heating the porous material treated with a molten salt mixture of CaCl₂-Ca(NO₃)₂.     

Synthesis of Compositionally Homogeneous Sr(CuxZn1−x)1/2W1/2O3

A complex perovskite of Sr(Cu _x Zn_{1- x} )_1/2 W_1/2O₃ (SCZW) is synthesized by a new combination of wet and dry processess. Mixed oxides containing Cu²⁺ and Zn²⁺ (CZ) are prepared by the wet process (coprecipitate method). SCZW is obtained by the dry process (mixed-oxide method) from a mixture of CZ, SrCO₃, and WO₃. SCZW has practically no compositional, unlike solid solutions prepared by the conventional dry method. The wet–dry process method is useful because the wet process is applied to only B-site cations having the same valence.     

Fabrication and Microstructure Characterization of Ti3SiC2 Synthesized from Ti/Si/2TiC Powders Using the Pulse Discharge Sintering (PDS) Technique

Ti/Si/2TiC powders were prepared using a mixture method (M) and a mechanical alloying (MA) method to fabricate Ti₃SiC₂ at 1200°–1400°C using a pulse discharge sintering (PDS) technique. The results showed that the Ti₃SiC₂ samples with <5 wt% TiC could be rapidly synthesized from the M powders; however, the TiC content was always >18 wt% in the MA samples. Further sintering of the M powder showed that the purity of Ti₃SiC₂ could be improved to >97 wt% at 1250°–1300°C, which is ∼200°–300°C lower than that of sintered Ti/Si/C and Ti/SiC/C powders using the hot isostatic pressing (HIPing) technique. The microstructure of Ti₃SiC₂ also could be controlled using three types of powders, i.e., fine, coarse, or duplex-grained, within the sintering temperature range. In comparison with Ti/Si/C and Ti/SiC/C mixture powders, it has been suggested that high-purity Ti₃SiC₂ could be rapidly synthesized by sintering the Ti/Si/TiC powder mixture at relatively lower temperature using the PDS technique.     

Characterization of alicyclic polyimides based on cyclobutane ring dianhydride and aromatic diamine

Films of alicyclic polyamic acid and polyimide containing cyclobutane ring in dianhydride moiety and aromatic ring with p- or m-linkages in diamine moiety were characterized by infrared (IR) spectroscopy, dynamic viscoelasticity, differential-scanning calorimetry (DSC), density, and wide-angle X-ray diffraction analyses. Partially and fully imidized polyimides were obtained by varying the imidization temperature, e.g., 150°C, 250°C, and 350°C. It was found from the results of IR spectra, dynamic viscoelasticity, and DSC measurements that the imidization of alicyclic polyamic acid was reduced at about 150°C and needed a higher imidization temperature than aromatic polyamic acid. Alicyclic polyimide with m-linkage in the diamine moiety had a higher density and a much more ordered structure than with p-linkage. © 1994 John Wiley & Sons, Inc.     

Application of pulse discharge sintering (PDS) technique to rapid synthesis of Ti3SiC2 from Ti/Si/C powders

To synthesize Ti₃SiC₂ samples, pulse discharge sintering (PDS) technique was utilized to sinter elemental powders of Ti/Si/C with stoichiometric and off-stoichiometric ratios in a temperature range of 1200–1500 °C. The results showed that high purity Ti₃SiC₂ could not be obtained from the Ti/Si/C powder with molar ratio of 3:1:2, and Ti₃SiC₂ preferred to form at relatively low sintering temperature for a short time. When 5Ti/2Si/3C and 3Ti/1.5Si/2C powders were sintered for 15 min, the TiC content was respectively decreased to 6.4 and 10 wt.% at 1250–1300 °C. The corresponding relative density of the samples sintered from 5Ti/2Si/3C powder was calculated to be as high as 99% at the temperature above 1300 °C. It is suggested that low-temperature rapid synthesis of Ti₃SiC₂ would be possible through the PDS technique, provided that the composition of the starting powders should be adjusted to be off-stoichiometric ratio from 3:1:2.     

Association and physical gelation of ABA triblock copolymer in selective solvent

Association behavior and physical gelation mechanism of ABA triblock copolymer dissolved in B-selective solvent have been studied systematically from dilute to moderately concentrated solutions. Static and dynamic light scattering and nuclear magnetic resonance measurements for dilute solutions of poly(methyl methacrylate)-block-poly(tert-butyl acrylate)-block-poly(methyl methacrylate) (PMMA-PtBuA-PMMA) in 1-butanol (PtBuA selective solvent) indicated that PMMA-PtBuA-PMMA chains are molecularly dissolved above 50 °C. With decreasing temperature, the triblock copolymers form associated micelles consisting PMMA associated core and PtBuA shell. Linear dynamic viscoelastic measurements for solutions with moderate concentration (3.9-12.0 wt%) revealed that the system was viscous sol state at 60 °C. Drastic increase of shear storage modulus (G′) occurred with decreasing temperature, and at 25 °C, G′ showed rubbery plateau with weak frequency dependency, means the formation of elastic physical gel. The consistency between the temperature for micelle formation and that at the increase in G′ indicates that the physical gelation is owing to the network formation as the result of the association of PMMA chains and the bridging PtBuA chains connecting the PMMA cores. Master curves for the dynamic moduli were derived by time-temperature superposition along the frequency axis. Just above sol-gel transition concentration (C_gel), the master curves suggest the existence of fairy amount of aggregate that is not incorporated in the macroscopic network. With the increase in polymer concentration, the master curves become to reveal Maxwell-type viscoelasticity with narrow relaxation time distribution, suggesting the formation of transient network with easily generation and destruction of crosslinks. Concentration dependency of the plateau modulus is stronger than the theoretically expected, means the macroscopic transient network grows with polymer concentration by increasing the fraction of elastically effective bridging PtBuA chain above C_gel.     

Influence of ammonium salt on electrowinning of copper from ammoniacal alkaline solutions

In order to develop an energy-saving copper recycling process from wastes, electrochemical measurements were conducted in ammoniacal alkaline solutions containing Cu(I) ions and an ammonium salt of sulfate, chloride or nitrate. The results of each system were then compared. The polarization measurements suggested that the voltage required for the electrode process is lower in the chloride and nitrate systems than that in the sulfate system. The cathode current efficiency during the copper electrodeposition varied from 39 to 97% and increased with current density in the chloride and sulfate systems. In the nitrate system, the lowest cathode current efficiency of 30% was observed because of nitrate ion reduction. Based on these results, the power consumption required for the electrowinning stage of the copper recycling process was calculated. Among these three systems, the chloride system showed the lowest power consumption of 500 kWh t⁻¹ at the current density of 200 A m⁻², which is about 25% of the conventional copper electrowinning process from a copper sulfate-sulfuric acid solution.