Effect of Magnetic Plane Defects on Thermal Conductivity of Solid 3He in U2D2 Phase

We calculate the thermal conductivity of solid ³ He in U2D2 phase. In this system, magnons are the dominant heat carriers. The experiment by Feng et al. shows that scattering magnon by some kind of magnetic defects becomes important at low temperature. We suppose the defects are the magnetic plane defects (MPD) which are originated by lattice dislocation and calculate the thermal conductivity with Kapitza Resistance Model (KRM).     

Experiment and numerical simulation of double-layered RC plates under impact loadings

This paper is to investigate and to propose a method to improve the impact resistance of reinforced concrete (RC) plates against projectile impact, and the damage of double-layered RC plates is examined experimentally and simulated analytically. In tests, a projectile launching apparatus, which is a 40 mm smooth-bore airgun, was used. Based on experimental results, numerical simulations with the DYNA-3D code, which takes account of the dynamic constitutive law of concrete, were done to find the applicability of the present computer code to the analysis of double-layered RC plates under high-speed impact loadings. In this study, the impact resistance of concrete plate is defined as the degree of local damage. In both experiments and numerical simulations, the effect of double-layering on the impact resistance is discussed.     

Development of a laser wavefront sensor for measurement of discharges in air

A laser wavefront sensor of the Shack‐Hartmann type capable of simultaneous measurement at two wavelengths was constructed. The sensor uses a single optical path, and is suited for applications such as high‐voltage discharges in air, in which large insulation distances are necessary. The sensor was used to detect optical path differences due to an impulse discharge in air across a needle–plane electrode gap of gap length 17 mm. Optical path differences were measured at laser wavelengths of 532 and 1064 nm at 1.6 µs after insulation breakdown across the gap. From the difference in optical path differences at the two wavelengths, a line‐integrated electron density distribution in the direction perpendicular to the gap was obtained near the high‐voltage electrode. The distribution had a peak value of 1.4 × 10²⁰m^?2 and a full width at half maximum of 4.4 mm. Because of the coverage of a large observation area including the entire gap, the spatial resolution was 1.4 mm, which was inadequate to obtain the precise form of the electron density distribution. However, the results show the possibility of applying laser wavefront sensing to electron density measurement. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 146(4): 10–17, 2004; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10247     

Establishment of a modified rankine method for the separate determination of free and combined sulphites in foods. III

Summary Considerable improvements were made to the original Rankine method. Replacement of aspiration with an injection system contributed a great deal to the simplification of procedure, being accompanied with an increase in reproducibility. Air (flow rate 1.01/min) was used for injection because the use of inert gas gave little increase in recovery rate.Sodium bisulphite (free sulphite) and three kinds of combined sulphite compound (bisulphite adducts of acetaldehyde, pyruvic acid and D-mannose) were used to find the most suitable conditions for the separate determination of free and combine sulphites.Free sulphite was expelled from the sample by bubbling at 0 °C for 30 min. It was confirmed that no combined sulphite was dissociated under these conditions. The phosphoric acid concentration had an important role in the liberation of sulphite. When 25% phosphoric acid was used, more than 99% of free sulphite was expelled by cold bubbling and more than 99% of combined sulphite was recovered by heating afterwards for 10 min.The scope of the modified Rankine method was also extended to the determination of sulphite in concentrated orange juice.

---

Verwendung der modifizierten Rankine-Methode zur getrennten Bestimmung von Sulfiten in Lebensmitteln. III

Zusammenfassung Die Rankine-Methode wurde bedeutend verbessert. Ein Umtausch der Aspiration mit Blasensystem trug beträchtlich zur Vereinfachung des Bestimmungsverfahrens bei, und die Reproduzierbarkeit wurde verbessert. Luft (Fließrate 1,01/min) wurde als Blasengas benutzt, da der Gebrauch von Inertgas für die Wiederfindungsrate unbedeutend ist.Natriumhydrogensulfit (freies Sulfit) und drei Arten gebundener Sulfite (Acetaldehydhydrogensulfit, Pyruvathydrogensulfit undd-Mannosehydrogensulfit) dienten dazu, die geeignetsten Bedingungen für die getrennte Bestimmung der freien und gebundenen Sulfite zu ermitteln.Freies Sulfit wurde bei 0 °C durch 30 min Durchblasen vertrieben. Hierbei ging kein gebundenes Sulîit verloren. Die Phosphorsäurekonzentration war wichtig für die Freisetzung des Sulfites. Wenn man 25%ige Phosphorsäure verwendet, werden > 99% freien Sulfites beim Durchblasen in der Kälte vertrieben, während > 99% gebundenen Sulfites durch nachheriges 10 min langes Erhitzen wiedergewonnen werden.Die modifizierte Rankine-Methode wurde weiterhin für konzentrierte Säfte verwendet.

---

---

Studies on the Analyses of Sulphites in Foods (III)     

An effective database formation for decision support systems

Managers' tasks have two aspects: to monitor (control) business activities and to plan the future based upon the monitored results. Thus a decision Support System (DSS) must have two kinds of databases appropriate for its needs.A management database, i.e., one for monitoring activities, is constructed mainly from the existing operational databases. A data cube should be employed for the logical data structure of the management database so that managers can share it and access it in multiple ways.Planning databases, i.e., those for planning activities, are constructed mostly from the management database. A table form should be employed for its logical data structure so that managers will find it easy to use.The management and planning databases should be connected through DSS's system architecture [1]. This makes the operational data (indicating business activities) directly and immediately available for management decision making.We have previously presented the DSS architecture. This paper discusses the management and planning databases from the viewpoint of it.     

Iron and steel industry of Japan

Founded at the turn of the century, Japan’s steel industry ranks sixth in world production. This article, written exclusively for Journal of Metals, tells of this historical development, as well as the current problems and achievements of the Japanese steel industry.     

Polymeric semiconducting carbon from fullerene by pulsed laser ablation

The polymeric semiconducting carbon films are grown on silicon and quartz substrates by excimer (XeCl) pulsed laser deposition (PLD) technique using fullerene C₆₀ precursor. The substrate temperature is varied up to 300 °C. The structure and optical properties of the films strongly depend on the substrate temperature. The grain size is increased and uniform polymeric film with improved morphology at higher temperature is observed. The Tauc gap is about 1.35 eV for the film deposited at 100°C and with temperature the gap is decreased upto 1.1 eV for the film deposited at 250 °C and increased to about 1.4 eV for the film deposited at 300 °C. The optical absorption properties are improved with substrate temperature. Raman spectra show the presence of both G peak and D peak and are peaked at about 1590 cm^− 1 and 1360 cm^− 1, respectively for the film deposited at 100 °C. The G peak position remains almost unchanged while D peak has changed only a little with temperature might be due to its better crystalline structure compared to the typical amorphous carbon films and might show interesting in device such as, optoelectronic applications.     

Application of GEMSAFE to ITER CDA and Its comparison with FER

A safety analysis for the design of International Thermonuclear Experimental Reactor (ITER) in the Conceptual Design Activity stage was performed by the GEMSAFE methodology, and its results were compared with those of Fusion Experimental Reactor (FER), a Japan's facility planned next to JT-60. The objectives of this study are to confirm the applicability of GEMSAFE to ITER and to select design basis events of ITER and identify R&D items with comparison to FER. Function-Based Safety Analyses (FBSA) were carred out to select 19 and 25 design basis events for FER and ITER, respectively. The major reason for the difference is that ITER has a class-2 RI source, e.g., tritium of 7.5 × 10⁵ Ci in mobile form, in the coolant for the first wall and blankets as well as a class-3 RI source, e.g., the immobile tritium of 2.2×10⁷ Ci absorbed in first wall and dust.