Strength improvement and purification of Yb2Si2O7‐SiC nanocomposites by surface oxidation treatment

A two‐step processing was developed to prepare Yb₂Si₂O₇‐SiC nanocomposites. Yb₂Si₂O₇‐Yb₂SiO₅‐SiC composites were first fabricated by a solid‐state reaction/hot‐pressing method. The composites were then annealed at 1250°C in air for 2 hours to activate the oxidation of SiC, which effectively transformed the Yb₂SiO₅ into Yb₂Si₂O₇. The surface cracks purposely induced can be fully healed during the oxidation treatment. The treated composites have improved flexural strength compared to their pristine composites. The mechanism for crack healing and silicate transformation have been proposed and discussed in detail.     

Comparative study of Al2O3, HfO2, and HfAlOx for improved self‐compliance bipolar resistive switching

The comparison of resistive switching (RS) storage in the same device architecture is explored for atomic layer deposition (ALD) Al₂O₃, HfO₂ and HfAlO_x‐based resistive random access memory (ReRAM) devices. Among them, the deeper high‐ and low‐ resistance states, more uniform V_SET‐V_RES, persistent R_OFF/R_ON (>10²) ratio and endurance up to 10⁵ cycles during both DC and AC measurements were observed for HfAlO_x‐based device. This improved behavior is attributed to the intermixing of amorphous Al₂O₃/HfO₂ oxide layers to form amorphous thermally stable HfAlO_x thin films by consecutive‐cycled ALD. In addition, the higher oxygen content at Ti/HfAlO_x thin films interface was found within the energy dispersive spectroscopy analysis (EDS). We believe this higher oxygen content at the interface could lead to its sufficient storage and supply, leading to the stable filament reduction‐oxidation operation. Further given insight to the RS mechanism, SET/RESET power necessities and scavenging effect shed a light to the enhancement of HfAlO_x‐based ReRAM device as well.     

The effects of solution properties and polyelectrolyte on electrospinning of ultrafine poly(ethylene oxide) fibers

The effects of solution properties and polyelectrolyte on the electrospinning of poly(ethylene oxide) (PEO) solutions were investigated. Ultrafine PEO fibers without beads were electrospun from 3, 4, 7 and 7 wt% PEO solutions in chloroform, ethanol, (dimethylformamide) DMF and water, respectively. At these concentrations, the values of [η]C were ∼10 for all solutions. The average diameters of PEO fibers were ranged from 0.36 to 1.96 μm. The higher the dielectric constant of solvent was, the thinner PEO fiber was. The average diameters of electrospun PEO fibers from PEO/water solutions were decreased and their distributions were narrowed by adding 0.1 wt% poly(allylamine hydrochloride) (PAH) and poly(acrylic acid sodium salt) (PAA) due to the increased charge density in solutions. The addition of PAH and PAA lowered the minimum concentration for electrospinning of a PEO/water solution to 6 wt%.     

One-step metal electroplating and patterning on a plastic substrate using an electrically-conductive layer of few-layer graphene

Few-layer graphene (FLG) was investigated as an electrically-conductive interleaf layer for one-step electroplating and patterning of metal on nonconductive polymer substrates without using multiple and toxic pretreatment processes in traditional electroplating. An individual FLG (5–10 nm of thickness with 6.4% of oxygen content) was obtained by expanding graphite with microwave followed by exfoliating the expanded graphite with sonication in N-methyl-pyrrolidone. Stacking FLG in the in-plane direction, a robust FLG film was obtained by the vacuum-assisted filtering and drying methods, and transferred to a polyethylene terephthalate (PET) substrate via an intermediate transfer to the water surface. The sheet resistance of the FLG film on the PET substrate was 0.9 kΩ/sq with a thickness of 80 nm and the root-mean-square roughness of 29 nm. In the electroplating of nickel on the FLG film, hemisphere-shape metal seeds appeared in the early stage of electroplating and they subsequently grew up to 200–480 nm, which became connected to form a continuous nickel layer. The thickness of the continuous nickel layer increased linearly with electroplating time. The developed electroplating method demonstrated its capability of selective patterning on nonconductive substrates using a simple masking technique.     

Synthesis and properties of natural rubber modified with stearyl methacrylate and divinylbenzene by graft polymerization

The graft polymerizations of stearyl methacrylate (SMA) and divinylbenzene (DVB) onto natural rubber (NR) were carried out in a solution process using benzoyl peroxide (BPO) as an initiator in toluene or chloroform. The main products of the grafted NR include an uncrosslinked (sol) part [sol(SMA–NR–DVB): s‐SNRD] and a crosslinked (gel) part [gel(SMA–NR–DVB), g‐SNRD]. s‐SNRD was obtained by extraction using tetrahydrofuran. It was identified by IR and ¹H‐NMR spectroscopies. The glass transition temperature (T_g) and thermal properties of s‐SNRD and g‐SNRD were studied by DSC and TGA. The glass transition temperature and thermal decomposition temperature of s‐SNRD and g‐SNRD were higher than were those of NR. The light resistance and weatherability of s‐SNRD were measured with a Weather‐o‐Meter. The light resistance and weatherability of s‐SNRD are better than are those of NR. The effects of the initiator concentration, mol ratio of SMA to DVB, reaction time, temperature on grafting ratio, and crosslinking ratio were investigated. The highest grafting ratio and crosslinking ratio in the graft polymerization of SMA and DVB onto NR were obtained when the mol ratio of SMA to DVB and BPO were 4.0 and 2 wt %, at 80°C for 48 h, respectively. Following several studies on oil‐absorptive polymers in our laboratory, 9 the oil absorptivity of g‐SNRD was examined using crude oil. The oil absorptivity of g‐SNRD was 600% when the immersion time was 10 min. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 2464–2470, 2001     

Structural and optical properties of ZnS thin films deposited by RF magnetron sputtering

Zinc sulfide [ZnS] thin films were deposited on glass substrates using radio frequency magnetron sputtering. The substrate temperature was varied in the range of 100°C to 400°C. The structural and optical properties of ZnS thin films were characterized with X-ray diffraction [XRD], field emission scanning electron microscopy [FESEM], energy dispersive analysis of X-rays and UV-visible transmission spectra. The XRD analyses indicate that ZnS films have zinc blende structures with (111) preferential orientation, whereas the diffraction patterns sharpen with the increase in substrate temperatures. The FESEM data also reveal that the films have nano-size grains with a grain size of approximately 69 nm. The films grown at 350°C exhibit a relatively high transmittance of 80% in the visible region, with an energy band gap of 3.79 eV. These results show that ZnS films are suitable for use as the buffer layer of the Cu(In, Ga)Se₂ solar cells.     

Effect of intumescent compositions on flammable properties of ethylene vinyl acetate and polypropylene

An intumescent flame retardant (IFR) system was prepared by 2 ways. Firstly, bis(2,6,7‐trioxa‐1‐phosphabicyclo[2,2,2]octane‐1‐oxa‐4‐hydroxymethyl) phosphonate methyl (bis‐PM) was synthesized and characterized by ¹H nuclear magnetic resonance (NMR), ³¹P NMR, and Fourier transform infrared spectroscopies. This carbonization agent was mixed with melamine (ME), ammonium polyphosphate (APP), and pentaerythritol (PER) to constitute an IFR system. Secondly, an IFR system by reaction was prepared by reaction, and the presence of compositions in product was confirmed by ¹H NMR and Fourier transform infrared. Both of systems enhanced the flammable retardation of ethylene vinyl acetate (EVA) and polypropylene (PP). Flammability and thermal behaviors of IFR‐EVA and IFR‐PP were investigated by vertical burning test (UL‐94 V) and thermogravimetric analysis. Results indicated that the IFR systems performed excellent flame retardancy and antidripping ability for PP. At 30 wt% loading, the optimum flame retardant formulations that are bis‐PM/ME: 4/1, bis‐PM/ME/PER: 3/1/1, APP/ME/PER: 3/1/1, and bis‐PM/ME/PER/APP: 1.5/1.5/1/1 give UL‐94 V‐0 rating. However, V‐0 rating results were only obtained for EVA when systems contain bis‐PM/ME: 4/1 and bis‐PM/ME/PER: 3/1/1. The char yield from decomposition of the IFR‐EVA and IFR‐PP has effects on the flame retardancy and antidripping behaviors of EVA and PP.     

Preparation and characterization of ordered mesoporous Mg–Al–Co hydrotalcite based catalyst for decarboxylation of jatropha oil

This paper reported preparation of novel order mesoporous Mg–Al–Co hydrotalcite based catalysts through sol–gel procedure using precursors such Mg(NO₃)₂, Al(NO₃)₃ and Co(NO₃)₂ and Na₂CO₃. The catalyst also contained both acidity and basicity being very convenient for decarboxylation process of vegetable oil to green hydrocarbons. The alkaline media was maintained at pH 10 during the processes. Molar ratio of metal cations and temperature of the sol–gel processes were investigated for their effect in the mesoporous structure formation. The results showed that the procedure should be established at 70 °C with the molar Mg/Al/Co ratio of 1/5/0.2. Acidity and basicity of the mesoporous hydrotalcite based catalyst were demonstrated for their co-existence. The as-synthesized material at the suitable conditions was used as catalyst for decarboxylation of jatropha oil to obtain green hydrocarbons mainly belonging to diesel fraction. The decarboxylation was carried out at 400 °C for 3 h in closed auto-pressurized reactor exhibiting a yield of diesel involving hydrocarbons of over 70% after distillation and analysis. The result also confirmed that the acidity and basicity greatly accelerated the activity of the catalyst. Some techniques were used to characterizing the catalyst including XRD, SEM, TEM, TGA, NH₃-TPD, CO₂-TPD and BET, and GC–MS was also used to analyze the main product composition.     

X-ray absorption spectroscopies of Mg-Al-Ni hydrotalcite like compound for explaining the generation of surface acid sites

Hydrotalcite-like compound containing metal cations such as Mg²⁺, Al³⁺ and Ni²⁺ was characterized using Ni K-edge EXAFS and in situ Ni K-edge XANES techniques for clarifying its bonding environment around Ni²⁺ sites and structure changes during calcination from room temperature to 550 °C, respectively. At the fixed molar ratio of Mg/Ni/Al of 2/1/1, the results obtained from EXAFS analysis showed a slight blue shift before and after the calcination at 550 °C and a reduction in white line peak; the best fits of the two samples revealed tiny change in coordination number about 7 for Ni-O path but considerable difference for Ni-Mg(Al) path from about 4.5 to 9.5, confirming a modification from brucite like to mixed oxide structure. On the other hand, bond distances of the Ni-O and Ni-Mg paths nearly fixed at about 2.06 Å to 3.0 Å reflected stability of the cationic bond order on each plane, but partial collapse and decomposition of the interlayer formed by water molecules and anion CO ₃ ^2? after the calcination. Linear combination fit extracted from the in situ Ni K-edge XANES also confirmed the changes along with the calcination such as slow and fast decreases of brucite fraction at 150 °C and 330 °C, respectively, in corresponding to the mixed oxide fraction increases. The achieved bonding structures were also applied to explain acid-base occurrence of the hydrotalcite-like material, especially the acid sites generated by different static charges along with the bonds. The explanation was illustrated by NH₃-TPD method.