Dielectric reliability of stacked Al2O3–HfO2 MIS capacitors with cylinder type for improving DRAM data retention characteristics

Dielectric reliability in Al₂O₃(2–3.1nm)–HfO₂(3nm) stack capacitor with Metal–Insulator–Si(MIS) structure is investigated in this paper. We propose an optimized capacitor process through the Time–Dependent Dielectric Breakdown (TDDB) data under various process conditions. Furthermore, due to asymmetric current at both negative and positive voltage stress polarities, we show different lifetime extrapolation by a fluence–driven model. As a result, the maximum allowed operating voltage is projected to be 1.7V (failure rate 10ppm during 10year @ 85°C) for Data “0” retention lifetime.     

Wideband and compact folded loop antenna

A simple and successful design method that yields a wideband and compact antenna without a ground plane is proposed. The antenna, referred to as the folded loop antenna, can, with the right parameters, achieve wideband characteristics. Calculated and measured results agree well and more than 50% bandwidth (return loss /spl les/-10 dB) is obtained.     

An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.     

Spectrum efficient region-based resource allocation with fractional loading for FH-OFDMA cellular systems

A practical resource management method that can significantly reduce cochannel interference (CCI) and improve spectrum utilisation in FH-OFDMA packet-based cellular networks is presented. The proposed method seeks an effective combination of dynamic resource allocation with fractional coding and bit loading to respectively minimise CCI and maximise system throughput for a desired performance.     

Programmable analogue VLSI implementation for asymmetric sigmoid neural activation function and its derivative

A new CMOS VLSI implementation of an asymmetric programmable sigmoid neural activation function, as well as of its derivative, is presented. It consists of two coupled PMOS and NMOS differential pairs with different programmable bias currents that set the upper and lower limits of the sigmoid. The circuit works in the weak inversion region, for low power consumption and exponential envelope, or in strong inversion to achieve higher speeds. The results obtained from the theoretical transfer function, and from the simulations of the circuit implemented in AMI's 0.35 /spl mu/m technology, show a very good match.     

Polyimide foams from powder: Experimental analysis of competitive diffusion phenomena

In the present study, various diffusive processes have been investigated during foaming of powdered precursors of polyimide. A detailed analysis of the powdered precursor's characteristics allows for an enhanced morphological understanding of the resulting microstructures and foam unit cell. Parameters that are central to the foaming process such as particle morphology, volatile concentration and sorption-desorption processes are evaluated. Isothermal and non-isothermal desorption experiments have been carried out by thermogravimetric analysis (TGA), and specific diffusive processes have been correlated to thermodynamic and kinetic transitions by means of modulated differential scanning calorimetry (MDSC) of the corresponding materials. It was found that two primary fluxes of volatiles, one out of the external surface of the particles (responsible for volatile desorption) and the other into the growing bubble (responsible for vapor supersaturation inside the bubble) compete against each other creating a competitive scenario that becomes the controlling factor for potential inflation within the precursor particles.     

High Pressure Conductivity and Photoconductivity of Polyveratrole

Summary Electropolymerization of o-(CH₃O)₂C₆H₄ (Veratrole) in dry acetonitrile/tetrabutylammonium tetrafluoroborate at platinum electrode, yields a green polymeric conducting solid. As the pressure is increased, the material becomes more conductive, but sharp changes towards lower conductivity occur at 4.2 and 6.2 metric tons pressure, probably due to phase transitions. The photoconductivity shows an exponential increase as temperature is increased, but it shows reversible changes at 200 K, 225 K and 250 K during slow warming, also attributable to phase transitions. Photoconductivity of Polyveratrole increases with the radiation frequency, being higher under blue light than under red of infrared radiation and there is a linear increase of photoconductivity with radiation density. Conductivity transients show that the conductivity increases exponentially with time to the saturation point within few minutes, and it also decreases exponentially when the light is turned off and the circuit is open. This behaviour can be explained by formation and encounter of electron and hole as current carriers. A preliminary study indicates a piezoelectric effect for the material. absorption spectroscopy allowed the measurements of the material band gap.     

Design and practical implementation of multifrequency RF front ends using direct RF sampling

The use of direct RF sampling has been explored as a means of designing multifrequency RF front ends. Such front ends will be useful to multifrequency RF applications such as global navigation satellite system receivers that use global positioning system (GPS) L1, L2, and L5 signals and Galileo signals. The design of a practical multifrequency direct RF sampling front end is dependent on having an analog-to-digital converter whose input bandwidth accommodates the highest carrier frequency and whose maximum sampling frequency is more than twice the cumulative bandwidth about the multiple carrier signals. The principle of direct RF sampling is used to alias all frequency bands of interest onto portions of the Nyquist bandwidth that do not overlap. This paper presents a new algorithm that finds the minimum sampling frequency that avoids overlap. This design approach requires a multifrequency bandpass filter for the frequency bands of interest. A prototype front end has been designed, built, and tested. It receives a GPS coarse/acquisition code at the L1 frequency and GPS antispoofing precision code at both L1 and L2. Dual-frequency signals with received carrier-to-noise ratios in excess of 52 dB-Hz have been acquired and tracked using this system.     

Bi12TiO20 synthesized directly from bismuth (III) nitrate pentahydrate and titanium glycolate and its activity

Pure phase of sillenite structure, Bi₁₂TiO₂₀, was directly synthesized using stoichiometric bismuth (III) nitrate pentahydrate and titanium glycolate by co-precipitation. The influence of pH on the structure of Bi₁₂TiO₂₀ was studied in the pH range of 3–10. The sillenite structure was characterized using XRD and FTIR. The photo-degradation reaction of 4-nitrophenol (4-NP) was used to study photocatalytic activity of Bi₁₂TiO₂₀ as a function of the preparation pH. The rate of decomposition was followed by UV-vis and TOC. The beginning concentration of 4-NP, 44 ppm, decreased to less than 1 ppm within 30 min for all prepared catalysts. It was found that the decomposition rate constant of Bi₁₂TiO₂₀ is six times higher than those of either TiO₂ or Bi₂O₃ under the same conditions.     

A comparison of the thermoformability of a PPE/PP blend with thermoformable ABS. Part I: Small deformation methods

Different factors important in ascertaining the thermoformability of polymeric materials are identified and defined. These include resistance to sag, ease of flow, mold replication, deep draw capability, sensitivity to thermoforming temperature and speed, uniformity of thickness distribution, and post‐forming shrinkage and dimensional stability. Methods to study these properties can be classified into small deformation and large deformation methods. The small deformation methods, which are the subject of this paper, include dynamic temperature sweep tests, dynamic frequency sweep tests, stress relaxation time, and creep recovery tests. These tests were used to compare the thermoformabilities of a blend of polyphenylene ether (PPE) and polypropylene (PP) and thermoformable acrylonitrile butadiene styrene (ABS) resin. The dynamic temperature and frequency tests showed that the PPE/PP blend generally has a better viscoelastic balance than ABS implying a better balance between resistance to sag and ease of flow. Creep recovery tests suggested that the PPE/PP blend may offer better mold replication during thermoforming. Studies based on the stress relaxation time showed a lower residual stress build‐up in thermoformed PPE/PP blend than ABS implying better dimensional stability and a higher in‐service temperature window for the thermoformed PPE/PP blend than ABS. POLYM. ENG. SCI., 45:1369–1376, 2005. © 2005 Society of Plastics Engineers