FBOLES—outline of a frequency-based on-line expert system approach for fault diagnoses in nuclear power plants

The basic concept of a novel frequency-based on-line expert system (FBOLES) approach for on-line fault diagnoses in nuclear power plants has been presented previously. This paper reports further progress, and includes how to express the uncertainties of expert opinion in knowledge-bases and propagate then in inferences, and how to deal with imperfect knowledge-bases. It also describes the main elements of FBOLES and outlines how the system works under complex conditions including the dynamic behavior of signals during accidents, multiple failures, and on-line changes of plant operation mode. Its ability to diagnose root causes of accidents has been tested using the main steam and feedwater condensate systems of a full-scale, three-loop, 950 MW nuclear power plant simulated by the Tsinghua simulator. So far the results seem good.     

^125I,^131I诱发小鼠精子畸形发生率比较

本文选用 ICR 雄性小鼠,经腹腔分别注射不同剂量的~(125)I 及~(131)I,观察并比较它们对小鼠精子畸形发生率的影响及染毒后睾丸中放射性活度的变化。实验结果表明:(1)~(125)I 染毒后4—5周,0、185、370和555 kBq 各组精子畸形发生率分别为9.00‰、9.57‰、11.6‰及13.9‰;~(131)I 染毒后4—5周,上述各组精子畸形发生率分别为8.50‰、12.5‰、14.7‰和15.5‰;在相同注入量下,~(125)I 与~(131)I 诱发小鼠精子畸形发生率的差异各组均不显著(X~2检验,p>0.05)。(2)~(125)I、~(131)I 染毒后2h 至7天内,两者在睾丸中的放射性活度及变化规律相似,即在染毒后2h 达最高值,每克睾丸中~(125)I 和~(131)I 的放射性活度分别占初始注入量(370 kBq)的0.72％和0.50％,然后迅速下降,至一周时,仅分别占初始注入量的0.035％和0.011％。     

中小企业创业资源的形成机制研究

创业资源是创业的基础,创业过程的规律性和市场配置资源的基础作用影响和决定中小企业创业资源的内在功能和形成方式。对中小企业资源的形成机制进行了分析探讨,并分析了它们之间的内在关系。     

坐标旋转法的收敛性,误差估计及扩展

本文通过推广正规序列的定义,得到一个不等式,由此证明了统一计算初等函数数值的坐标旋转法的收敛性,作了误差估计,并拓广了所计算的函数范围,成为快速计算所有初等函数的统一算法．     

压缩弯曲小半径中频弯管工艺的研究

在分析了感应加热小半径弯管形变机理的基础上，提出了压缩弯曲的成型工艺，研制出了小半径中频弯管设备，并进行了大量的工艺实验和实验研究，取得了满意的结果。     

A circuit model for the class E resonant DC-DC converter regulatedat a fixed switching frequency

An averaging circuit model is developed for the class E resonant DC-DC converter regulated at a fixed switching frequency. The regulation is achieved by use of an auxiliary switch. The model is obtained based on the circuit analysis using the Fourier series expansion. Steady-state and small-signal dynamic analysis is presented, which reveals that the DC output is well controlled by the control angle of the auxiliary switch and that there exists a right-half-plane zero in the control-to-output transfer function. The analysis results are verified by the experiments     

在p+GaAs体单晶材料上进行的NEA活化实验

NEA活化实验是利用体单晶材料进行的,未经任何外延或真空解理手续。为确立活化工艺,特别是表面清洁处理规范,作了相应AES分析。借助于测量样品附近高纯Al的熔点以校准及控制样品表面的温度。在不太好的本底真空(2×10^-7—6×10^-7Pa)条件下,活化好的GaAs样品之白光光电灵敏度可达1000μA/lm以上。     

Insulating safety analysis of the hot-line sweeping robot

This paper presents a method of calculating the insulating safety distances for hot-line working robots at high voltage when dielectric is adulterated with conducts. Also, finite element method is adopted to calculate the electric field strength to find whether it is beyond the critical. The above methods have been applied to analyze the insulating safety of the robot for hot-line sweeping post insulators in a 220 KV substation. They have also been testified by experimentations.     

智能ABC输入法中特殊用键的应用

根据作者几年来的数学和实践经验，对智能ABC输入法的特殊用键的用法作以介绍。     

CFD Simulation of Liquid Film Flow on Inclined Plates

A two‐phase flow CFD model using the volume of fluid (VOF) method is presented for predicting the hydrodynamics of falling film flow on inclined plates, corresponding to the surface texture of structured packing. Using the proposed CFD model the influence of the solid surface microstructure, liquid properties and gas flow rate on the flow behavior was investigated. From the simulated results it was shown that under the condition of no gas flow the liquid flow patterns are dependent on the microstructure of the plates, and proper microstructuring of the solid surface will improve the formation of a continuous liquid film. It was also found that liquid properties, especially surface tension, play an important role in determining the thin‐film pattern. However, there are very different liquid film patterns under the action of gas flow. Thinner liquid films break easily, but thicker liquid films can remain continuous even at higher gas flow rates, which demonstrates that all factors affecting the liquid film thickness will affect the liquid film patterns under conditions of counter‐current two‐phase flow.