Computer-aided reaction system synthesis based on structured process energy-exergy-flow diagram

A computerized thermodynamics-oriented procedure for reaction system synthesis is proposed. First, hierarchy structure of chemical reactions is discussed and the reaction system is categorized into three types; (1) combination with a heat source or sink, (2) combination with a reaction donor, and (3) decomposition of target reaction into subtargets. Then, the algorithm to find subtarget reactions and/or donor reactions is presented.     

Iodine reaction of vinyl acetate/vinyl propionate copolymers. III. Iodine affinities of the radically polymerized copolymers and the copolymers derived from partially saponified polyvinyl acetate

The minimum sequence lengths (n_c) of vinyl acetate (VAc) units necessary to form a colored iodine complex were determined to be 4 and 17 for radically polymerized VAc/vinyl propionate (VPr) and VAc/isopropenyl acetate (IPAc) copolymers, respectively. The iodine affinities (I/VAc) of VAc/VPr copolymers (SP-series) obtained by propionylation of partially saponified polyvinyl acetate (PVAc) were remarkably affected by the saponification conditions. An increase of the water content in acetone/water mixture as saponification solvent brought about a decrease of the iodine affinities of the SP-series. The dependence of the iodine affinity on the saponification of monomer units in the SP-series was compared with that in the radically polymerized VAc/VPr copolymers by taking the sequence probability as the measure of monomer unit distribution. The results strongly supported an occurence of the slide fastener reaction at high degrees of saponification, which was well-known in the saponification of PVAc. Furthermore, it was found that the saponification mode of PVAc at low degrees of saponification was influenced uniquely by the water content in saponification solvents and the saponification temperature.     

Novel method of preparing Ag–Hg alloy on polyacrylamide films and their structure

A novel method is proposed of preparing thin Ag–Hg alloy on PAAm film surface at room temperature: The film of interest is formed by holding PAAm aqueous solution with AgNO₃ in Hg-saturated atmosphere. Two kinds of films, one of which is a conductor and the other an insulator, can be selectively formed with pH-controlled PAAm solution by ammonia. The conducting surface is assigned to the α phase of Ag–Hg alloy by means of X-ray analysis. Potentiometric titration and IR spectral studies suggest the existence of PAAm–Ag⁺ complexes. On the basis of their structure and the oxidation and reduction potential of Ag⁺ and Hg²⁺, the mechanism of film formation is also discussed.     

Temperature Dependence of KIC for High-Pressure Hot-Pressed Si3N4 Without Additives

Temperature dependence of K_IC values for Si₃N₄ bodies sintered at high pressures without additives was studied from room temperature to 1400°C. Little change in K_K was found in this range.     

Balanced corpus of contemporary written Japanese

The balanced corpus of contemporary written Japanese (BCCWJ) is Japan’s first 100 million words balanced corpus. It consists of three subcorpora (publication subcorpus, library subcorpus, and special-purpose subcorpus) and covers a wide range of text registers including books in general, magazines, newspapers, governmental white papers, best-selling books, an internet bulletin-board, a blog, school textbooks, minutes of the national diet, publicity newsletters of local governments, laws, and poetry verses. A random sampling technique is utilized whenever possible in order to maximize the representativeness of the corpus. The corpus is annotated in terms of dual POS analysis, document structure, and bibliographical information. The BCCWJ is currently accessible in three different ways including Chunagon a web-based interface to the dual POS analysis data. Lastly, results of some pilot evaluation of the corpus with respect to the textual diversity are reported. The analyses include POS distribution, word-class distribution, entropy of orthography, sentence length, and variation of the adjective predicate. High textual diversity is observed in all these analyses.     

Diffusion/adsorption model of cellulose dyeing. II. Ordinary cellulose–direct dye system

The diffusion and adsorption of C.I. Direct Yellow 12 and Blue 15 in water-swollen ordinary cellophane sheets were examined at various ionic strengths. The concentration dependence of apparent diffusion coefficients, D_c, for these dyes was obtained from the diffusion profiles in the substrate, which were measured by the use of the cylindrical film roll method. The decrease of apparent porosity with an increase in the amounts of adsorption was observed. To explain the diffusion/adsorption behaviors of these systems, a variable porosity model was proposed and was applied to analyze the concentration dependence of D_c's. The diffusion/adsorption behaviors of these dyes could be quantitatively described by this model at relatively low ionic strengths. At higher ionic strengths and/or lower values of C, i.e., at the large values of C_im/C_m, where the C's are the concentrations of immobilized (suffix im) and mobile (suffix m) species, it needed to introduce the concept of dynamic equilibria which occurred simultaneously with diffusion but deviated from the true equiliblia measured by the adsorption experiments.     

Glass transition behavior of emulsion-polymerized polymer films containing a surface-active agent

The glass transition behavior of emulsion-polymerized poly(methyl methacrylate) and polystyrene films containing sodium laurylsulfate as emulsifier was studied by measurements of dynamic mechanical properties and thermal depolarization current. The film specimens of the emulsion-polymerized polymers were prepared by casting from their benzene solutions. The glass transition temperatures of the emulsion-polymerized films are higher than those of the bulk-polymerized films. The higher glass transition temperature of the emulsion-polymerized films is attributed to the colloidal properties of sodium laurylsulfate in the process of the film formation. The restriction of the molecular chains in the emulsion-polymerized films is attributed to the interaction between the hydrophobic groups of sodium laurylsulfate and the polymer molecules.     

Hydrophobic effects on protein/nucleic acid interaction: enhancement of substrate binding by mutating tyrosine 45 to tryptophan in ribonuclease Tl

Hydrophobic effects on binding of ribonuclease Tl to guaninebases of several ribonucleotides have been proved by mutatinga hydrophobic residue at the recognition site and by measuringthe effect on binding. Mutation of a hydrophobic surface residueto a more hydrophobic residue (Tyr45 – Trp) enhances thebinding to ribonucleotides, including mononucleotide inhibitorand product, and a synthetic substrate-analog trinudeotide aswell as the binding to dinucleotide substrates and RNA. Enhancementson binding to non-substrate ribonucleotides by the mutationhave been observed with free energy changes ranging from –2.2 to – 3 .9 kJ/mol. These changes are in good agreementwith that of substrate binding, –2.3 kJ/mol, which iscalculated from Michaelis constants obtained from kinetic studies.It is shown, by comparing the observed and calculated changesin binding free energy with differences in the observed transferfree energy changes of the amino acid side chains from organicsolvents to water, that the enhancement observed on guaninebinding comes from the difference in the hydrophobic effectsof the side chains of tyrosine and tryptophan. Furthermore,a linear relationship between nucleolytic activities and hydrophobicityof the residues (Ala, Phe, Tyr, Trp) at position 45 is observed.The mutation could not change substantially the base specificityof RNase Tl, which exhibits a prime requirement for guaninebases of substrates.     

Characterization of alicyclic polyimides based on cyclobutane ring dianhydride and aromatic diamine

Films of alicyclic polyamic acid and polyimide containing cyclobutane ring in dianhydride moiety and aromatic ring with p- or m-linkages in diamine moiety were characterized by infrared (IR) spectroscopy, dynamic viscoelasticity, differential-scanning calorimetry (DSC), density, and wide-angle X-ray diffraction analyses. Partially and fully imidized polyimides were obtained by varying the imidization temperature, e.g., 150°C, 250°C, and 350°C. It was found from the results of IR spectra, dynamic viscoelasticity, and DSC measurements that the imidization of alicyclic polyamic acid was reduced at about 150°C and needed a higher imidization temperature than aromatic polyamic acid. Alicyclic polyimide with m-linkage in the diamine moiety had a higher density and a much more ordered structure than with p-linkage. © 1994 John Wiley & Sons, Inc.     

Hydrothermal Formation of Hydroxyapatite Layers on the Surface of Type-A Zeolite

Type-A zeolite evenly covered with hydroxyapatite thin layers was prepared using hydrothermal treatment at 120°C for 8 h under autogenous pressure. The hydroxyapatite needlelike nanocrystals, 100–200 nm in diameter and 30 nm in thickness, were grown under the reaction between discharged Ca²⁺ ions from type-A zeolite and PO₄³⁻ ions in (NH₄)₃PO₄ solution. The preferential orientations of the c -axis of hydroxyapatite crystals perpendicular to a zeolite surface were observed using transmission electron microscopy. The crystal structure of type-A zeolite was not destroyed under the reaction, but the surface morphology was changed only with complete covering of scaly hydroxyapatite particles.