This work deals with the study of hydrothermally synthesized zinc oxide (ZnO) loaded mesoporous SBA‐15 hybrid nanocomposite for relative humidity sensing (RH) at room temperature. The sensor exhibits an excellent ~5 orders impedance change along with excellent linearity, quick response time (17 s), rapid recovery time (18 s), negligible hysteresis (1.2%), good repeatability, and stability (1.8%) in 11%–98% RH range. In addition, complex impedance spectra of the sensor at different RHs were analyzed to understand the humidity sensing mechanism. Our study can open a new way for realizing ZnO/SBA‐15 hybrid nanocomposite for fabrication of high‐performance RH sensors. 相似文献
The structural, electronic, and elastic properties of pristine and carbon‐doped boron suboxide (B6O) are calculated using density functional theory. The results indicate that it is energetically preferable for a single carbon atom to substitute into an oxygen site rather than a boron site. The lattice parameters and cell volume increase to relieve the residual stress created by the carbon substitution. The interstitial position is not favorable for a single atom substitution. However, if two carbon atoms substitute for two neighboring oxygen atoms, then it becomes energetically favorable to dope an interstitial oxygen, boron, or carbon atom along the C–C chain. If the interstitial dopant is either boron or carbon, a local B4C‐like structure with either a C–B–C or C–C–C chain is created within the boron suboxide unit cell. The resulting structure shows improvements in the bulk modulus at the expense of the shear and Young's moduli. The moduli further improve if an additional carbon is substituted within a polar or equatorial site of the neighboring B12 icosahedron. Based on these calculations, we conclude that carbon doping can either harden or soften B6O depending on the manner in which the substitutions are populated. Furthermore, as B6O samples are often oxygen deficient, C doping can occupy such sites and improve the elastic properties. 相似文献
In order to reveal the unsteady features of gas–solid flow, the pressure fluctuations were measured at different locations along the length of the pipeline while conveying powders through the pipeline. Power spectral density (PSD) functions were obtained for the analysis of the pressure fluctuation. Two types of powders (fly ash and alumina) were used in this analysis. The PSD analysis was conducted by taking into account different aspects such as flow conditions (dilute or dense), location of transmitter (top and bottom transmitters), location of transmitter along the length of the pipeline (three different locations), material property (fly ash or alumina), etc. Analysis of signals from top and bottom transmitters shows that it is not possible to identify the flow mode at upper and lower portions of pipeline. The magnitude of power is found to be higher for alumina as compared to fly ash. PSD parametric analysis reveals that frequency bandwidth and average power decreases exponentially with increase in solid loading ratio. 相似文献
Metal Science and Heat Treatment - Composites obtained by powder metallurgy from a mixture of copper powders and graphene nanosheets are studied. The response surface methodology is used to design... 相似文献
Silicon - Ceramic composites are extremely sensitive to the surrounding environment. Their tribological performance may degrade drastically if they are polluted by some external agent. The present... 相似文献
The tensile fracture behavior of oxide dispersion strengthened 18Cr (ODS-18Cr) ferritic steels milled for varying times was studied along with the oxide-free 18Cr steel (NODS) at 25, 200, 400, 600, and 800 °C. At all the test temperatures, the strengths of ODS–18Cr steels increased and total elongation decreased with the duration of milling time. Oxide dispersed 18Cr steel with optimum milling exhibited enhanced yield strength of 156 pct at room temperature and 300 pct at 800 °C when compared to oxide-free 18Cr steel. The ductility values of ODS-18Cr steels are in the range 20 to 35 pct for a temperature range 25 to 800 °C, whereas NODS alloy exhibited higher ductility of 37 to 82 pct. The enhanced strength of ODS steels when compared to oxide-free steel is due to the development of ultrafine grained structure along with nanosized dispersion of complex oxide particles. While the pre-necking elongation decreased with increasing temperature and milling time, post-necking elongation showed no change with the test temperature. Fractographic examination of both ODS and NODS 18Cr steel fractured tensile samples, revealed that the failure was in ductile fracture mode with distinct neck and shear lip formation for all milling times and at all test temperatures. The fracture mechanism is in general followed the sequence; microvoid nucleation at second phase particles, void growth and coalescence. The quantified dimple sizes and numbers per unit area were found to be in linear relation with the size and number density of dispersoids. It is clearly evident that even nanosized dispersoids acted as sites for microvoid nucleation at larger strains and assisted in dimple rupture.
Patients with epithelial ovarian cancer (EOC) are often diagnosed at an advanced stage due to nonspecific symptoms and ineffective screening approaches. Although chemotherapy has been available and widely used for the treatment of advanced EOC, the overall prognosis remains dismal. As part of the intrinsic defense mechanisms against cancer development and progression, immune cells are recruited into the tumor microenvironment (TME), and this process is directed by the interactions between different chemokines and their receptors. In this review, the functional significance of CXC chemokine ligands/chemokine receptors (CXCL/CXCR) and their roles in modulating EOC progression are summarized. The status and prospects of CXCR/CXCL-based theranostic strategies in EOC management are also discussed. 相似文献
The solidification of a molten layer of amorphous thermoplastic between cooled parallel plates is used to model the mechanics of part warpage in the injection-molding process. Flow effects are neglected, and a thermorheologically simple thermoviscoelastic material model is assumed. The model allows material to be added to fill the space created by the pressure applied during solidification so that this model can be used to assess packing-pressure effects in injection molding. Parametric results are presented on the effects of the mold temperatures and the packing pressure—the pressure applied during solidification to counteract the effects of volumetric shrinkage of the thermoplastic—on the in-plane and through-thickness shrinkages, on warpage, and on residual stresses in plaque-like geometries. The packing pressure is shown to have a significant effect on part warpage. While the results are presented in terms of normalized variables based on the properties of bisphenol-A polycarbonate, they can be interpreted for other amorphous thermoplastics, such as modified polyphenylene oxide, polyetherimide, and acrylonitrile-butadiene-styrene. 相似文献