Molds and Resists Studies for Nanoimprint Lithography of Electrodes in Low-Voltage Polymer Thin-Film Transistors

A low-cost patterning of electrodes was investigated looking forward to replacing conventional photolithography for the processing of low-operating voltage polymeric thin-film transistors. Hard silicon, etched by sulfur hexafluoride and oxygen gas mixture, and flexible polydimethylsiloxane imprinting molds were studied through atomic force microscopy (AFM) and field emission gun scanning electron microscopy. The higher the concentration of oxygen in reactive ion etching, the lower the etch rate, sidewall angle, and surface roughness. A concentration around 30 % at 100 mTorr, 65 W and 70 sccm was demonstrated as adequate for submicrometric channels, presenting a reduced etch rate of 176 nm/min. Imprinting with positive photoresist AZ1518 was compared to negative SU-8 2002 by optical microscopy and AFM. Conformal results were obtained only with the last resist by hot embossing at 120 °C and 1 kgf/cm² for 2 min, followed by a 10 min post-baking at 100 °C. The patterning procedure was applied to define gold source and drain electrodes on oxide-covered substrates to produce bottom-gate bottom-contact transistors. Poly(3-hexylthiophene) (P3HT) devices were processed on high-κ titanium oxynitride (TiO _x N _y ) deposited by radiofrequency magnetron sputtering over indium tin oxide-covered glass to achieve low-voltage operation. Hole mobility on micrometric imprinted channels may approach amorphous silicon (～0.01 cm²/V s) and, since these devices operated at less than 5 V, they are not only suitable for electronic applications but also as sensors in aqueous media.     

A DSL for specifying run-time adaptations for embedded systems: an application to vehicle stereo navigation

The traditional approach for specifying adaptive behavior in embedded applications requires developers to engage in error-prone programming tasks. This results in long design cycles and in the inherent inability to explore and evaluate a wide variety of alternative adaptation behaviors, critical for systems exposed to dynamic operational and situational environments. In this paper, we introduce a domain-specific language (DSL) for specifying and implementing run-time adaptable application behavior. We illustrate our approach using a real-life stereo navigation application as a case study, highlighting the impact and benefits of dynamically adapting algorithm parameters. The experiments reveal our approach effective, as such run-time adaptations are easily specified in a higher level by the DSL, and thus at a lower programming effort than when using a general-purpose language such as C.     

Effects of nisin concentration on properties of gelatin film-forming solutions and their films

The addition of nisin into a gelatin matrix can change properties of the film. The aim of this work was to develop gelatin-based films containing different nisin concentrations in order to study their influence on the film's antimicrobial and physical properties and their rheological properties as a film-forming solution (FFS). The FFS was characterised by rheological assays, and the gelatin-based active films were characterised and assessed by the effects of nisin concentrations on their various properties, including antimicrobial activity. Nisin's concentration affected not only its viscoelastic properties of FFS but also its film solubility in water, film surface roughness and light barrier. The addition of nisin also slightly modified the water contact angle and the mechanical properties of the gelatin films. Finally, the films demonstrated activity against Staphylococcus aureus and Listeria monocytogenes at concentrations above 56 mg of nisin g⁻¹ of gelatin.     

Design of frameworks for self-adaptive service-oriented applications: A systematic analysis

Self-adaptive service-oriented Applications (Self-Apps) must be able to understand themselves or the environment in which they are executed, and propose solutions to meet changing conditions. The development of these applications is not a trivial task, since it encompasses issues from different research areas. Despite the importance of frameworks for Self-Apps, there is a lack of comprehensive analysis of how the design of such applications is performed, and regarding the standardization of concepts and coverage of minimum requirements for Self-Apps. The main contribution of this article is to present this comprehensive analysis, providing the state of the art for this subject. This analysis was built through a Systematic Mapping Study, based on a total of 65 studies, from which we identify the main attributes for Quality of Service (QoS), search strategies, and service management strategies employed in the design of frameworks for Self-Apps. The main aspects of requirements involved in the design of Self-Apps were pointed out to stakeholders. For example, these applications must implement a method for evaluation of QoS based on metrics. We also put forward the S-Frame, a modular solution that brings together the main features for the design of Self-Apps, and describe the main challenges concerning these applications.     

Rheological properties of wheat flour and quality characteristics of pan bread as modified by partial additions of wheat bran or whole grain wheat flour

The use of bran and whole grain flour changes dough rheology and causes difficulties in manufacturing bakery products. The aim of this study was to analyse the influence of substituting refined wheat flour (WF) by wheat bran (WB; 5%, 10%, 20%, 30% and 40%) or whole grain wheat flour (WGWF; 10%, 20%, 30%, 40% and 50%) on dough rheological properties and pan bread quality characteristics. The addition of WB and WGWF increased water absorption and resistance to extension and decreased stability, extensibility and peak viscosity. Effects with WB were more pronounced. The presence of WB or WGWF increased crumb moisture content, firmness and hardness and decreased specific volume of pan bread. It is important to set new farinographic and extensographic standards when using WB and WGWF, allowing for a correct correlation between rheology and quality characteristics of bakery products, as the same standards used for WF are not valid.     

Identifying organizational requirements for the implementation of Advanced Manufacturing Technologies (AMT)

AMT selection and adoption processes have been extensively studied. Topics that include financial and human factors, productivity, and coordination of the AMT implementation establish a substantial content of the present research agenda. The purpose of this paper is to study the organizational factors that influence the AMT implementation, considering a manufacturing strategy context and an analysis based on an organizational design framework. The research strategy is based on ‘empirical iterations’ using survey secondary data, experts’ interviews information and multiple case studies. The results show that there is a set of recommendations, which strongly influence the AMT implementation. Companies require a structured and integrative approach for the AMT implementation in order to take advantage of all their individual and systemic benefits. The set of proposed AMT recommendations for integrating these technologies to the organizational design are framed by structural, process and contextual aspects.     

An assessment of energy benefits of efficient household air-conditioners in Brazil

Increasing efficiency of electrical equipment is essential to national energy rationality, enabling energy consumption reduction and postponing inversion in distribution, transmission and generation, as well as mitigating environmental impacts associated with such activities. Considering such purposes, two actions have been promoted in Brazil: (a) minimum energy performance standards (MEPS) have been required for some appliances and (b) consumers have been informed about the most efficient products by ??endorsement labeling.?? The purpose of this study is to assess window and split air-conditioners with Brazilian MEPS. To evaluate the impact of efficient air-conditioners in this market, a model was developed based on estimates for quantity of equipment in operation and unitary consumption, as determined by local temperature records. From this model, it was deduced that using only efficient conditioners (class A for Brazilian Labeling Program/INMETRO, with PROCEL Label) an annual saving of 322?GWh and a reduction in demand of 109?MW could be obtained in 2007. Furthermore, it was observed that the current MEPS established by Brazilian legislation for air-conditioners may be considered relatively low. Considering that MEPS are similar to those observed in China (the main exporter of air-conditioners to the Brazil), an energy saving of roughly 222?GWh could be achieved in the same year. Impacts on emission of greenhouse gases are also estimated.     

Optimization of osmotic dehydration of yacon slices

Osmotic dehydration assisted by ultrasound (ODAU) at low temperatures reduces water activity (a_w) and maintains nutrients. The influence of solution concentration (SC; 20 to 60° Brix, xylitol and sorbitol) and ultrasound application time (t_us, 0 to 40 min) in ODAU of yacon was studied with the aid of a response surface method. The optimum condition with respect to mass transfer parameters, a_w, and fructan retention was SC of 60° Brix for both solutions and t_us of 2.67 min for xylitol samples and 0 min for sorbitol samples. The application of ultrasound improved dehydration but resulted in depolymerization of fructans.     

Hydromorphological,hydraulic and ecological effects of restored wood: findings and reflections from an academic partnership approach

Large wood (re)introduction can deliver multiple benefits in river restoration, but there is a dearth of the detailed and longer‐term post‐project monitoring and evaluation required for improving best practice. We present findings from an academic partnership approach to post‐project evaluation, based on successive MSc research projects on restored large wood in the Loddon catchment, UK. Field and modelling data reveal: (i) key differences in large wood features between restored and natural reaches; (ii) increased hydraulic retention and changes to mesohabitats associated with large wood; (iii) differences in macroinvertebrate community composition around large wood but a lack of site‐level effects; (iv) interactions between macrophytes and large wood that may be specific to restored reaches; (v) a need for further field and modelling studies to inform the accurate representation of large wood in hydraulic models. Some key challenges in partnership working are identified to aid planning and effectiveness of future collaborations.