The effects of slider design on thermal asperity rejection capability

Particle contamination has been an ongoing problem affecting the reliability of the magnetic hard disk drives. Especially the recent use of MR head requires much tighter control of particle contamination due to thermal asperity (TA) phenomenon. In this study, the effects of slider air bearing surface design on TA reduction capability were investigated by manufacturing two types of sliders. Numerical methods were used to simulate the motion of particles in the head/media interface. Experiments were conducted to verify the results predicted by the numerical simulation. Drives were built and exposed to particle contamination using a particle injection chamber, which turned out to be a very simple and reliable particle generation method over conventional aerosol technique. Then the number of TA generated in the drives was recorded and compared. Also the contacts between slider and particles were investigated by acoustic emission study. It was found that a new ABS design, which has aerodynamic U-shaped rail and central flow passage, was beneficial in reducing the particle contamination on the slider.     

Implementing the Double Bootstrap

The single bootstrap already is popular in economics, though the double bootstrap has better convergence properties. We discuss the theory and implementation of the double bootstrap, both with and without the pivotal transformation, and give detailed examples of each. One example is a nonlinear double bootstrap of a Cobb-Douglas production function, and explains the use of Gauss-Newton Regressions as a device to decrease computational time. Another example is double bootstrapping elasticities from a translog production function.     

119Sn magic angle spinning NMR of nanocrystalline SnO2

Nanocrystalline SnO2 samples of different grain sizes, prepared by inert gas condensation technique (IGCT) and chemical precipitation method and conforming to the tetragonal phase, have been studied by variable speed (3-10 kHz) 119Sn MAS NMR at 11.74 Tesla field. 119Sn solid-state NMR results show that the IGCT prepared samples have good crystallinity and phase purity compared to the samples prepared by the chemical method. The determination of 119Sn chemical shielding parameters (delta iso, delta delta and eta) from slow MAS spectra shows that the 119Sn isotropic chemical shift (delta iso) is strongly influenced at smaller grain sizes, attributable to the change in the O2- local symmetry for the surface 119Sn ions at smaller grain sizes. The observed line widths in MAS spectra are significantly larger than the life-time broadening due to spin-lattice (T1) and spin-spin (T2) relaxation. The 119Sn MAS NMR spectra are thus inhomogeneously broadened by a distribution of isotropic chemical shifts, the line broadening increasing with decrease in grain size.     

Use of waste materials--Bottom Ash and De-Oiled Soya, as potential adsorbents for the removal of Amaranth from aqueous solutions

Bottom Ash, a power plan t waste material and De-Oiled Soya, an agriculture waste product were successfully utilized in removing trisodium 2-hydroxy-1-(4-sulphonato-1-naphthylazo)naphthalene-3,6-disulphonate--a water-soluble hazardous azo dye (Amaranth). The paper incorporates thermodynamic and kinetic studies for the adsorption of the dye on these two waste materials as adsorbents. Characterization of each adsorbent was carried out by I.R. and D.T.A. curves. Batch adsorption studies were made by measuring effects of pH, adsorbate concentration, sieve size, adsorbent dosage, contact time, temperature etc. Specific rate constants for the processes were calculated by kinetic measurements and a first order adsorption kinetics was observed in each case. Langmuir and Freundlich adsorption isotherms were applied to calculate thermodynamic parameters. The adsorption on Bottom Ash takes place via film diffusion process at lower concentrations and via particle diffusion process at higher concentrations, while in the case of De-Oiled Soya process only particle diffusion takes place in the entire concentration range.     

Experimental study of gamma radiation induced degradation of a piezoresistive pressure sensor

Microsystem Technologies - This paper reports the experimental investigation of gamma radiation induced degradation of a piezoresistive pressure sensor with total dose exposure up...     

High-Temperature Tensile Behaviors of Base Metal and Electron Beam-Welded Joints of Ni-20Cr-9Mo-4Nb Superalloy

Electron beam welding of Ni-20Cr-9Mo-4Nb alloy sheets was carried out, and high-temperature tensile behaviors of base metal and weldments were studied. Tensile properties were evaluated at ambient temperature, at elevated temperatures of 625 °C to 1025 °C, and at strain rates of 0.1 to 0.001 s^?1. Microstructure of the weld consisted of columnar dendritic structure and revealed epitaxial mode of solidification. Weld efficiency of ~?90 pct in terms of strength (UTS) was observed at ambient temperature and up to an elevated temperature of 850 °C. Reduction in strength continued with further increase of test temperature (up to 1025 °C); however, a significant improvement in pct elongation is found up to 775 °C, which was sustained even at higher test temperatures. The tensile behaviors of base metal and weldments were similar at the elevated temperatures at the respective strain rates. Strain hardening exponent ‘n’ of the base metal and weldment was ~?0.519. Activation energy ‘Q’ of base metal and EB weldments were 420 to 535 kJ mol^?1 determined through isothermal tensile tests and 625 to 662 kJ mol^?1 through jump-temperature tensile tests. Strain rate sensitivity ‘m’ was low (<?0.119) for the base metal and (<?0.164) for the weldment. The δ phase was revealed in specimens annealed at 700 °C, whereas, twins and fully recrystallized grains were observed in specimens annealed at 1025 °C. Low-angle misorientation and strain localization in the welds and the HAZ during tensile testing at higher temperature and strain rates indicates subgrain formation and recrystallization. Higher elongation in the weldment (at Test temperature >?775 °C) is attributed to the presence of recrystallized grains. Up to 700 °C, the deformation is through slip, where strain hardening is predominant and effect of strain rate is minimal. Between 775 °C to 850 °C, strain hardening is counterbalanced by flow softening, where cavitation limits the deformation (predominantly at lower strain rate). Above 925 °C, flow softening is predominant resulting in a significant reduction in strength. Presence of precipitates/accumulated strain at high strain rate results in high strength, but when the precipitates were coarsened at lower strain rates or precipitates were dissolved at a higher temperature, the result was a reduction in strength. Further, the accumulated strain assisted in recrystallization, which also resulted in a reduction in strength.     

Multi-objective optimization of process parameters in Electro-Discharge Diamond Face Grinding based on ANN-NSGA-II hybrid technique

The effective study of hybrid machining processes (HMPs), in terms of modeling and optimization has always been a challenge to the researchers. The combined approach of Artificial Neural Network (ANN) and Non-Dominated Sorting Genetic Algorithm-II (NSGA-II) has attracted attention of researchers for modeling and optimization of the complex machining processes. In this paper, a hybrid machining process of Electrical Discharge Face Grinding (EDFG) and Diamond Face Grinding (DFG) named as Electrical Discharge Diamond face Grinding (EDDFG) have been studied using a hybrid methodology of ANN-NSGA-II. In this study, ANN has been used for modeling while NSGA-II is used to optimize the control parameters of the EDDFG process. For observations of input-output relations, the experiments were conducted on a self developed face grinding setup, which is attached with the ram of EDM machine. During experimentation, the wheel speed, pulse current, pulse on-time and duty factor are taken as input parameters while output parameters are material removal rate (MRR) and average surface roughness (R_a). The results have shown that the developed ANN model is capable to predict the output responses within the acceptable limit for a given set of input parameters. It has also been found that hybrid approach of ANN-NSGA-II gives a set of optimal solutions for getting appropriate value of outputs with multiple objectives.     

Development of noncontact end effector for handling of bakery products

The application of automation for handling of nonrigid or semirigid products and air permeable materials is limited due to lack of suitable end effectors. The majority of robotic manipulators and end effectors are not easily applicable because of lack of contact rigidity with nonrigid or semirigid products due to their unpredictable and unstable behaviour and with materials which are sensitive to deformation, especially bakery products (baked and unbaked) in the biscuits industry (Erzincanli and Sharp, Food Control 8:185–190, 1997). Also, during the handling process, the risk of contamination is high due to direct contact with food products. Hence, the need for noncontact robotic end effectors is strongly felt. In this paper a noncontact type end effector having a rectangular cross-section designed for handling bakery products is discussed for use in the biscuits manufacturing industry. These end effectors operate on the principle of generating vacuum, which lifts the material without any mechanical contacts. The present work explores the possibility of using radial flow nozzles in the biscuits industry. The basic working principle is presented, followed by experimental results. An automatic noncontact end effector system may be found quite useful for the food handling industry.