Novel hollow mesoporous 1D TiO2 nanofibers as photovoltaic and photocatalytic materials

Hollow mesoporous one dimensional (1D) TiO(2) nanofibers are successfully prepared by co-axial electrospinning of a titanium tetraisopropoxide (TTIP) solution with two immiscible polymers; polyethylene oxide (PEO) and polyvinylpyrrolidone (PVP) using a core-shell spinneret, followed by annealing at 450 °C. The annealed mesoporous TiO(2) nanofibers are found to having a hollow structure with an average diameter of 130 nm. Measurements using the Brunauer-Emmett-Teller (BET) method reveal that hollow mesoporous TiO(2) nanofibers possess a high surface area of 118 m(2) g(-1) with two types of mesopores; 3.2 nm and 5.4 nm that resulted from gaseous removal of PEO and PVP respectively during annealing. With hollow mesoporous TiO(2) nanofibers as the photoelectrode in dye sensitized solar cells (DSSC), the solar-to-current conversion efficiency (η) and short circuit current (J(sc)) are measured as 5.6% and 10.38 mA cm(-2) respectively, which are higher than those of DSSC made using regular TiO(2) nanofibers under identical conditions (η = 4.2%, J(sc) = 8.99 mA cm(-2)). The improvement in the conversion efficiency is mainly attributed to the higher surface area and mesoporous TiO(2) nanostructure. It facilitates the adsorption of more dye molecules and also promotes the incident photon to electron conversion. Hollow mesoporous TiO(2) nanofibers with close packing of grains and crystals intergrown with each other demonstrate faster electron diffusion, and longer electron recombination time than regular TiO(2) nanofibers as well as P25 nanoparticles. The surface effect of hollow mesoporous TiO(2) nanofibers as a photocatalyst for the degradation of rhodamine dye was also investigated. The kinetic study shows that the hollow mesoporous surface of the TiO(2) nanofibers influenced its interactions with the dye, and resulted in an increased catalytic activity over P25 TiO(2) nanocatalysts.     

Optimum difference mode excitations for monopulse arrays

A technique has been developed to obtain optimum difference mode excitations for monopulse arrays. In addition, a direct interpolation scheme has been devised for situations where near-optimum results would suffice. A parameter designated asu_{0}is identified with every optimum difference pattern. The choice of this parameteru_{0}determines the sidelobe level of the optimum pattern. The problem of obtaining the optimum excitations has been shown to be reducible to one of finding out the best approximation that minimizes the maximum deviation (minimax) from the real line (u = betad cos varpaxis), over a range determined byu_{0}. This latter problem has been solved using a modified Remez exchange algorithm. An extensive set of design curves has also been presented.     

Electron Paramagnetic Resonance and optical absorption spectra of Cr(III) ions in alkali cadmium borosulphate glasses

The Electron Paramagnetic Resonance (EPR) spectrum at 9.205 GHz and at 300 K has been examined for a series of Cr³⁺ ions doped alkali cadmium borosulphate [R₂SO₄-CdSO₄-B₂O₃ (R=Li,Na,K or Cs)] glasses. The low field EPR spectral resonance lines are attributed to isolated Cr³⁺ ions where as the high field spectral resonance lines are attributed to exchange coupled pairs of Cr³⁺ ions. The absorption spectra of Cr³⁺ ions ions in these glasses show two broad bands characteristic of Cr³⁺ ions in octahedral symmetry. The bands are slightly shifted to higher wavelength side from Li glass to Cs glass. From the optical spectra the crystal field parameter Dq and the Racah interelectronic repulsion parameters B and C are evaluated. From the EPR and optical data, it is concluded that, the site symmetry around the Cr³⁺ ions is octahedral and the nature of bonding is predominantly covalent in nature.     

Conductive electrospun PANi-PEO/TiO2 fibrous membrane for photo catalysis

The integration of electrospinning and electrospraying to prepare the fibrous catalytic filter membrane is demonstrated. The non-conductive polyethylene oxide (PEO) is blended with (±)-camphor-10-sulfonic acid (CSA) doped conductive polyaniline (PANi) for electrospinning. The conductive CSA/PANi-PEO composite fibers are produced upon electrospinning, which are used as the conductive collector for electrospraying process by which titanium dioxide (TiO₂) nanoparticles (NPs) are sprayed and allowed to adsorb on the fibers. The degree of adsorption and dispersion of nano TiO₂ catalysts on the surface of the CSA/PANi-PEO fibers exhibit a stronger dependence on weight percentage (wt%) of PANi in PEO solution and the strength of electrical conductivity of the fibers used during electrospraying. CSA/PANi-PEO fibers as collector reduce the wastage of TiO₂ NPs during electrospraying to lesser than 5%. Among the three different composition of PANi studied, PEO with 12 wt% PANi yields very uniform diameter and beads-free fibrous structure with higher electrical conductivity. 12 wt% CSA/PANi-PEO fibrous membrane is found to support for greater dispersion of TiO₂ NPs. The photocatalytic activity of the as-prepared TiO₂-PANi-PEO catalytic membrane is tested against the toxicant simulant 2-chloroethyl phenyl sulfide (CEPS) under the ultraviolet light irradiation. It is observed that the TiO₂ nanoparticles catalysts embedded PANi-PEO fibrous membrane decontaminated the toxicant CEPS significantly, which is due to uniform dispersion of the catalysts produced by the methodology.     

The processing electronics system for the pointed mode operation ofIXAE on the Indian satellite IRS-P3

Indian Remote Sensing Satellite-P3 (IRS-P3: 1996-017A) was launched into a near-Earth, polar, Sun-synchronous orbit by India's Polar Satellite Launch Vehicle (PSLV-D3) on March 21, 1996. The Indian X-ray Astronomy Experiment (IXAE) is one of the prime payloads onboard IRS-P3. IXAE has two sets of detectors: three pointed-mode proportional counters (PPCs) and one X-ray Sky Monitor (XSM). IRS-P3 is configured to operate in two modes, namely, Earth-pointing mode and stellar-pointing mode. In Earth-pointing mode the remote sensing payloads are in operation; in addition, XSM maps the sky for bright X-ray sources and X-ray transients. In stellar mode, the PPCs observe several Galactic, bright X-ray, and extragalactic sources. The microprocessor-based processing electronics system was designed and developed for PPC data-handling and telemetering the stored data to the ground station. The system has been working well from the day the IXAE was commissioned. The processing electronics system for the PPCs, its interfaces, and the in-orbit instrument performance are described. Some results of the pointed mode observations are also presented     

Mineralization of osteoblasts with electrospun collagen/hydroxyapatite nanofibers

Regeneration of fractured or diseased bones is the challenge faced by current technologies in tissue engineering. The major solid components of human bone consist of collagen and hydroxyapatite. Collagen (Col) and hydroxyapatite (HA) have potential in mimicking natural extracellular matrix and replacing diseased skeletal bones. More attention has been focused on HA because of its crystallographic structure similar to inorganic compound found in natural bone and extensively investigated due to its excellent biocompatibility, bioactivity and osteoconductivity properties. In the present study, electrospun nanofibrous scaffolds are fabricated with collagen (80 mg/ml) and Col/HA (1:1). The diameter of the collagen nanofibers is around 265 ± 0.64 nm and Col/HA nanofibers are 293 ± 1.45 nm. The crystalline HA (29 ± 7.5 nm) loaded into the collagen nanofibers are embedded within nanofibrous matrix of the scaffolds. Osteoblasts cultured on both scaffolds and show insignificant level of proliferation but mineralization was significantly (p < 0.001) increased to 56% in Col/HA nanofibrous scaffolds compared to collagen. Energy dispersive X-ray analysis (EDX) spectroscopy results proved the presence of higher level of calcium and phosphorous in Col/HA nanocomposites than collagen nanofibrous scaffolds grown osteoblasts. The results of the present study suggested that the designed electrospun nanofibrous scaffold (Col/HA) have potential biomaterial for bone tissue engineering.     

On the stability of fuzzy systems

Studies the global asymptotic stability of a class of fuzzy systems. It demonstrates the equivalence of stability properties of fuzzy systems and linear time invariant (LTI) switching systems. A necessary and sufficient condition for the stability of such systems are given, and it is shown that under the sufficient condition, a common Lyapunov function exists for the LTI subsystems. A particular case when the system matrices can be simultaneously transformed to normal matrices is shown to correspond to the existence of a common quadratic Lyapunov function. A constructive procedure to check the possibility of simultaneous transformation to normal matrices is provided