A New Triazole-Thiol Compound Organofunctionalized on the Silica Gel Surface: Chemical Properties and Copper Sorption in Ethanol / Water Media

Silicon - This study describes the preparation and characterization of 3-chloropropyl silica gel with 4-amino-5-(4pyridyl)-4H-1,2,4-triazole-3-thiol (SGA) for copper adsorption in different media....     

Surface Pretreatments of Silicon Nitride for CVD Diamond Deposition

The efficiency of different surface pretreatments (four standard chemical etchings and four diamond powder abrasive procedures) on silicon nitride (Si₃N₄) substrates for chemical vapor deposition (CVD) of diamond has been systematically investigated. Blank Si₃N₄ samples were polished with colloidal silica (∼0.25 μm). Diamond nucleation and growth runs were conducted in a microwave plasma chemical vapor deposition apparatus for 10 min and 6 h, respectively. Superior results concerning nucleation density ( N _d∼ 10¹⁰ cm⁻² after 10 min), film uniformity, and grain size (below 2 μm after 6 h) were obtained for the mechanically microflawed samples, revealing that chemical etchings (hot and cold strong acids, molten base or CF₄ plasma) are not crucial for good CVD diamond quality on Si₃N₄.     

Evaluation of the thermal and mechanical properties of poly(ε‐caprolactone), low‐density polyethylene,and their blends

The thermal and mechanical properties of low‐density polyethylene (LDPE), poly(ε‐caprolactone) (PCL), and their blends were evaluated. Differential scanning calorimetry showed that increasing the PCL content of the blend did not change the LDPE melting temperature, but reduced the crystallinity by up to 16.8%. This behavior was related to interactions between the PCL chains and the crystalline phase of LDPE. Tensile strength and elongation at break values for the blends were lower than those for the pure polymers, which suggested an incompatibility between the polymers. The values for Young's modulus under tensile increased when PCL was added to LDPE. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91:3909–3914, 2004     

Li influx and binding, and li/mg competition in bovine chromaffin cell suspensions as studied by li NMR and fluorescence spectroscopy

Li(+) influx by bovine chromaffin cells, obtained from bovine adrenal medulla, was studied in intact cell suspensions using (7)Li NMR spectroscopy with the shift reagent [Tm(HDOTP)](4-). The influx rate constants, k(i), were determined in the absence and in the presence of two Na(+) membrane transport inhibitors. The values obtained indicate that both voltage sensitive Na(+) channels and (Na(+)/K(+))-ATPase play an important role in Li(+) uptake by these cells. (7)Li NMR T(1) and T(2) relaxation times for intracellular Li(+) in bovine chromaffin cells provided a T(1)/T(2) ratio of 305, showing that Li(+) is highly, immobilized due to strong binding to intracellular structures. Using fluorescence spectroscopy and the Mg(2+) fluorescent probe, furaptra, the free intracellular Mg(2+) concentration in the bovine chromaffin cells incubated with 15 mM LiCl was found to increase by about mM after the intracellular Li(+) concentration reached a steady state. Therefore, once inside the cell, Li(+) is able to displace Mg(2+) from its binding sites.     

Spectroscopic Multicomponent Analysis Using Multi-objective Optimization for Variable Selection

The multiple determination tasks of chemical properties are a classical problem in analytical chemistry. The major problem is concerned in to find the best subset of variables that better represents the compounds. These variables are obtained by a spectrophotometer device. This device measures hundreds of correlated variables related with physicocbemical properties and that can be used to estimate the component of interest. The problem is the selection of a subset of informative and uncorrelated variables that help the minimization of prediction error. Classical algorithms select a subset of variables for each compound considered. In this work we propose the use of the SPEA-II （strength Pareto evolutionary algorithm II）. We would like to show that the variable selection algorithm can selected just one subset used for multiple determinations using multiple linear regressions. For the case study is used wheat data obtained by NIR （near-infrared spectroscopy） spectrometry where the objective is the determination of a variable subgroup with information about E protein content （%）, test weight （Kg/HI）, WKT （wheat kernel texture） （%） and farinograph water absorption （%）. The results of traditional techniques of multivariate calibration as the SPA （successive projections algorithm）, PLS （partial least square） and mono-objective genetic algorithm are presents for comparisons. For NIR spectral analysis of protein concentration on wheat, the number of variables selected from 775 spectral variables was reduced for just 10 in the SPEA-II algorithm. The prediction error decreased from 0.2 in the classical methods to 0.09 in proposed approach, a reduction of 37%. The model using variables selected by SPEA-II had better prediction performance than classical algorithms and full-spectrum partial least-squares.     

Influence of the silica matrix on the formation of α-alumina in a mullite–alumina composite from a diphasic precursor

In mullite–alumina composite precursors, interaction between the silica matrix and the fine -alumina texture strongly influences the precursor phase transformation, the nucleation and the crystal geometry both of the mullite and of the -alumina. The mullite–alumina composite precursor calcined at 1000 °C has a layered structure probably derived from the layered texture of the -alumina. The phase transition of this layered texture is retarded by the presence of the silica matrix and a metastable mullite phase is formed before nucleation of -alumina. By leaching away the silica matrix, the remaining layered texture is readily transformed into very fine, thin -alumina platelets by calcination at 1000 °C. This seems to be one reason for the appearance of elongated mullite grains in a pure mullite matrix and the platelet shaped -alumina grains in the mullite–alumina composite prepared from diphasic precursors. © 1998 Chapman & Hall     

Performance analysis of available bandwidth estimation tools for grid networks

Modern large-scale grid computing systems for processing advanced science and engineering applications rely on geographically distributed clusters. In such highly distributed environments, estimating the available bandwidth between clusters is a key issue for efficient task scheduling. We analyze the performance of two well known available bandwidth estimation tools, pathload and abget, with the aim of using them in grid environments. Differently than previous investigations (Jain et al., ; Shriram et al., in Passive and active network measurement: 6th international workshop, PAM 2005. Springer, Berlin, 2005), our experiments consider a series of relevant metrics such as accuracy of the estimation, convergence time, degree of intrusion in the grid links, and ability to handle multiple simultaneous estimations. No previous work has analyzed the use of available bandwidth tools for the derivation of efficient grid scheduling.     

An haptic-based immersive environment for shape analysis and modelling

Currently, the design of aesthetic products is a process that requires a set of activities where digital models and physical mockups play a key role. Typically, these are modified (and built) several times before reaching the desired design, increasing the development time and, consequently, the final product cost. In this paper, we present an innovative design environment for computer-aided design (CAD) surface analysis. Our system relies on a direct visuo-haptic display system, which enables users to visualize models using a stereoscopic view, and allows the evaluation of sectional curves using touch. Profile curves are rendered using an haptic device that deforms a plastic strip, thanks to a set of actuators, to reproduce the curvature of the shape co-located with the virtual model. By touching the strip, users are able to evaluate shape characteristics, such as curvature or discontinuities (rendered using sound), and to assess the surface quality. We believe that future computer-aided systems (CAS)/CAD systems based on our approach will contribute in improving the design process at industrial level. Moreover, these will allow companies to reduce the product development time by reducing the number of physical mockups necessary for the product design evaluation and by increasing the quality of the final product, allowing a wider exploration and comparative evaluation of alternatives in the given time.     

Induction motor fault detection and diagnosis using a current state space pattern recognition

In the last few decades the continuous monitoring of complex dynamic systems has become an increasingly important issue across diverse engineering areas. This paper presents a pattern recognition based system that uses visual-based efficient invariants features for continuous monitoring of induction motors. The procedures presented here are based on the image identification of the 3-D current state space patterns that allow the identification of distinct fault types and, furthermore, their corresponding severity. This automatic fault detection system deals with time-variant electric currents and is based on the identification of three-phase stator currents specified patterns. Several simulation and experimental results are also presented in order to verify the effectiveness of the proposed methodology.