Evaluation of HBsAg carrier rate in acute viral hepatitis and high risk individuals using RPHA and ELISA

INTRODUCTION: Balloon valvuloplasty in neonates and small infants with critical aortic stenosis is a palliative procedure. The present report describes the results of the technique in our center. METHODS: From April 1993 to March 1995, six consecutive patients with critical aortic valve stenosis underwent catheter-balloon valvuloplasty. Their ages ranged from 2 to 120 days old (45.5 +/- 47.5 days). Four patients had associated lesions: 2 had coarctation of the aorta, 1 had ischemic dilated cardiomyopathy and 1 had endocardial fibroelastosis. Percutaneous femoral artery access was used in four cases and axillary artery dissection in two. RESULTS: The balloon-annulus diameter ratio was 0.92 +/- 0.12. The peak systolic ejection gradient decreased from 66.1 +/- 26.4 to 38 +/- 15.7 mmHg (p < 0.05) and the left ventricle systolic pressure decreased from 136.3 +/- 26.8 to 115 +/- 22.5 mmHg (p < 0.05). There were no mortalities related to the procedure. Both patients who had aortic coarctation developed aortic regurgitation and died after repairing of the coarctation. The patient with endocardial fibroelastosis died during an attempt to perform the Norwood operation (Stage I) and the other patient with ischemic dilated cardiomyopathy survived after cardiac transplantation. The remaining two patients with isolated aortic valve stenosis are currently asymptomatic. CONCLUSIONS: Catheter-balloon valvuloplasty is an effective procedure in the initial treatment of critical aortic stenosis and may be life saving.     

Catalytic oxidation of toluene and m-xylene by activated carbon fiber impregnated with transition metals

The catalytic oxidation of volatile organic compounds (VOCs) into mainly CO₂ and H₂O appears promising in the context of the abatement of atmospheric gaseous pollutants and is the subject of this paper. The catalytic oxidation of toluene and m-xylene was carried out in a tubular reactor on a phenolic resin based activated carbon fiber (ACF) impregnated with nitrates of Co, Cr, Ni, and Cu at the reaction temperatures below 300 °C. The extent of the removal (i.e. conversion) of toluene and m-xylene was examined through the breakthrough curves and was found to strongly depend on the types and loading of the metal precursors. The experimental results showed that the reaction rate was significantly affected by O₂ concentration below 3% (v/v). The performance of the ACFs impregnated with 5% (w/w) of Ni oxide was found to be superior to that of other metal oxides at reaction temperature between 170 and 290 °C. A surface kinetic mechanism for the catalytic oxidation of volatile organic compound was proposed and incorporated in a transport model developed to explain the experimental breakthrough data.     

Design of Probability Density Function Targeting Energy Efficient Network for Coalition Based WSNs

Energy consumption is one of the important issues in wireless sensor network that rely on non chargeable batteries for power. Also, the sensor network has to maintain a desired sensing coverage area along with periodically sending of the sensed data to the base station. Therefore, coverage and the lifetime are the two important issues that need to be addressed. Effective deployment of wireless sensors is a major concern as the coverage and lifetime of any wireless sensor network depends on it. In this paper, we propose the design of a Probability Density Function (PDF) targeting the desired coverage, and energy efficient node deployment scheme. The suitability of the proposed PDF based node distribution to model the network architecture considered in this work has been analyzed. The PDF divides the deployment area into concentric coronas and provides a probability of occurrence of a node within any corona. Further, the performance of the proposed PDF is evaluated in terms of the coverage, the number of transmissions of packets and the lifetime of the network. The scheme is compared with the existing node deployment schemes based on various distributions. The percentage gain of the proposed PDF based node deployment is 32\(\%\) more than that when compared with the existing schemes. Thus, the simulation results obtained confirm the schemes superiority over the other existing schemes.     

Oxidation Behavior of Carbon Steel: Effect of Formation Temperature and pH of the Environment

The nature of surface oxide formed on carbon steel piping used in nuclear power plants affects flow-accelerated corrosion. In this investigation, carbon steel specimens were oxidized in an autoclave using demineralized water at various temperatures (150-300 °C) and at pH levels (neutral, 9.5). At low temperatures (< 240 °C), weight loss of specimens due to dissolution of iron in water occurred to a greater extent than weight gain due to oxide formation. With the increase in temperature, the extent of iron dissolution reduced and weight gain due to oxide formation increased. A similar trend was observed with the increase in pH as was observed with the increase in temperature. XRD and Raman spectroscopy confirmed the formation of magnetite. The oxide film formed by precipitation process was negligible at temperatures from 150 to 240 °C compared to that at higher temperatures (> 240 °C) as confirmed by scanning electron microscopy. Electrochemical impedance measurement followed by Mott–Schottky analysis indicated an increase in defect density with exposure duration at 150 °C at neutral pH but a low and stable defect density in alkaline environment. The defect density of the oxide formed at neutral pH at 150-300 °C was always higher than that formed in alkaline environment as reported in the literature.     

Microstructures using RF sputtered PSG film as a sacrificial layer in surface micromachining

In this paper, we explore RF magnetron sputtered Phosphor-silicate-glass (PSG) film as a sacrificial layer in surface micromachining technology. For this purpose, a 76 mm diameter target of phosphorus-doped silicon dioxide was prepared by conventional solid-state reaction route using P₂O₅ and SiO₂ powders. The PSG films were prepared in a RF (13·56 MHz) magnetron sputtering system at 300 watt RF power, 20 mTorr pressure and 45 mm target-to-substrate spacing without external substrate heating. Microstructures of sputtered silicon dioxide film were fabricated using sputtered PSG film as sacrificial layer in surface micromachining process.     

Parthenium sp. as a plant biomass for the production of alkalitolerant xylanase from mutant Penicillium oxalicum SAUE-3.510 in submerged fermentation

The use of congress grass (Parthenium sp.) and water hyacinth (Eichhornia crassipes) as low cost raw materials for xylanase production from mutant Penicillium oxalicum SAU_E-3.510 in submerged fermentation was investigated. For development of mutant from wild type P. oxalicum SA-8 ITCC 6024, a strategy of mixed mutagenesis was followed using UV-irradiation and ethidium bromide, which had resulted into 1.87 fold increases in the activity of the enzyme. For enzyme production, the fungus was cultivated in mineral medium containing congress grass as carbon source. Considerably higher levels of production (475.2 ± 6.0 IU ml^?1) were achieved in media containing congress grass, although it was slightly less than that was obtained (488.5 ± 6.5 IU ml^?1) in presence of commercial oat spelt xylan. This fact confirms the feasibility of using this low cost non-food resource as an alternative carbon source to save costs of the enzyme production process. Maximum xylanase activity was reported at 55 °C with its stability at 80 °C for 2 h. The highest activity of xylanase at pH 9.0 and its stability at similar pH for 24 h denote the alkalitolerant nature of enzyme.     

Effect of Amorphous Content on Dissolution Characteristics of Rifampicin

Rifampicin, one of the main first line anti-TB drugs, shows variable bioavailability in different marketed preparations and reasons cited include physiological, degradation, manufacturing/ processing, solid state, and bioavailability assessment procedure. Although the amorphous form of a drug is expected to exhibit higher solubility, the amorphous rifampicin has been reported to have a solubility disadvantage as compared to crystalline form II, which is used in marketed preparations. Amorphous form was generated and characterized by solid-state characterization techniques. Physical powder mixtures of form II with varying amounts of amorphous form were prepared, which were then subjected to solid-state characterization techniques and further evaluated for their dissolution behavior. Differential scanning calorimetry (DSC) scans show that area enclosed by integral of melting endotherm can be used for quantification of crystalline component, which can then be used to estimate amorphous content. No definite trend was evident in powder dissolution of mixtures that could implicate solubility difference of amorphous form. Intrinsic dissolution rate (IDR) results indicate that amorphous content has no effect on dissolution profiles of crystalline rifampicin.     

Cracking of superheater tube in a captive power plant

ABSTRACT

A steam generator unit in a captive power plant of a heavy water plant reported fish-mouth failure in the secondary super heater bend. The operating pressure of the super heater is 105?kg?cm^?2 and temperature is 485°C. The super heater tubes made of 2¼Cr–1Mo ferritic steel is exposed to steam at a pH of 9.5–10.5 and conductivity less than 2?µS?cm^?1 in the inner surface and at the outer surface exposed to flue gas. It has been operational for last 25 years. Layered deposits were observed at the failed region which were iron oxides. The investigations revealed that outer surface which has flue gas environment showed thinning with oxide scale spallation taking place. The SEM studies showed that there was extensive precipitation of molybdenum sulphide and carbides in the microstructure resulting in preferential oxidation along grain boundaries. The excessive outer thinning of tube resulted in fish-mouth failure of the super heater tube.

This paper is part of a supplementary issue from the 17th Asia-Pacific Corrosion Control Conference (APCCC-17).     

Logical Cell Formation in FMS, Using Flexibility-Based Criteria

Flexible manufacturing systems often are organized into a cellular architecture for ease of operation. The formation of these cells sometimes has been treated as an extension of the conventional cell-formation problem. This paper argues that, owing to the existence of flexible routing and transfer capabilities, the cell-formation problem in FMSs should be treated as quite distinct from that in conventional manufacturing systems and shows that a flexibility-based procedure is apt for overcoming the deficiencies of earlier forays into this area. Manufacturing cell flexibility is defined as a composite of three flexibility measures: producibility,processivity , and transferability. The problem of cell formation is modeled as flexibility maximization, and a procedure is developed for the simultaneous formation of machine cells and part families, while heuristically maximizing within-cell flexibility.     

Bulk production of porous TiO2 nanowires by unique solvo-plasma oxidation approach for combating biotic and abiotic water contaminants

Pure, porous titania nanowires (TiO₂-pNW) are produced in bulk amount (~?250 kg/day, reaction time scale?<?1 min) using a unique solvo-plasma oxidation method utilizing microwave plasma with the potential of easy scale up. The prepared nanowire is found to be efficient towards both biotic disinfection and destruction of various abiotic contaminants in wastewaters. In terms of organic contaminants, the TiO₂-pNW is tested for destruction of Rhodamine B (RhB) dye, tetracycline (TC) antibiotic, and diclofenac (DFC) and caffeine (CAF) drugs. In the case of biotic contaminants, the disinfection of E. coli bacteria is demonstrated. In all of the studies, the photocatalytic performance of anatase TiO₂-pNW is compared to that of commercially available P25 nanoparticles (TiO₂-P25), both in the presence and absence of ozone. The excellent photoactivity exhibited by TiO₂-pNW is a result of low recombination rate of electron–hole pair owing to the spatial separation of electrons and holes within the photoexcited nanowires. Moreover, the scavenger experiments and experiments involving ozone reveal that electron transfer and/or presence of dissolved oxygen are the major limiting factors for both porous titania nanowires and P25 spherical powder under UV exposure with photocatalytic activity towards pollutant degradation.