SHS of shape memory CuZnAl alloys

Aiming at preparation of shape memory alloys (SMAs), we explored the SHS of Cu_{1 − x} Zn_{1 − y} Al_{1 − z} alloys (0.29 < x < 0.30, 0.74 < y < 0.75, and 0.83 < z < 0.96). The most pronounced shape memory effect was exhibited by the alloys of the following compositions (wt %): (1) Cu(70.6)Zn(25.4)Al(4.0), (2) Cu(70.1)Zn(25.9)Al(4.0), and (3) Cu(69.9)Zn(26.1)Al(4.0). The effect of process parameters on the synthesis of CuZnAl alloys was studied by XRD, optical microscopy, and scanning electron microscopy (SEM). The grain size of CuZnAl was found to depend on the relative amount of the primary CuZn and AlZn phases. Changes in the transformation temperature and heat of transformation are discussed in terms of ignition intensity and compaction. Mechanism of the process depends on the level of the temperature attained relative to the melting point of components. At the melting point of AlZn, the process is controlled by the solid-state diffusion of AlZn into a product layer. The ignition temperature for this system depends on the temperature of the austenite-martensite transformation in CuZnAl alloys. The composition and structure of the products was found to markedly depend on process parameters. The SHS technique has been successfully used to prepare a variety of SMAs.      

Influence of a lipid phase on steam jet agglomeration of maltodextrin powders

The contribution of an oil phase to the agglomeration mechanisms of food powders was evaluated. Maltodextrin (DE 10), palm oil stearin and two palm oil oleins (up to 25% dry mass) were used as food models. Granulation runs were carried out in a pilot plant steam jet agglomerator. The powders containing oleins were more cohesive than those with stearin and the presence of oil changed the agglomeration mechanisms. The size increase mechanism of pure maltodextrin powder was controlled by surface plasticization and agglomerates with suitable instant properties were obtained. Small amount of oil degenerated drastically the rate of dispersion in water of the powders and their agglomerates but the average size and the mechanical resistance of the agglomerates increased when the oil content of the powders increased. SEM micrographs of agglomerates indicated that higher lipid content in the powders produced compact granules, favoring sinkability but hindering their disintegration. Agglomeration enhanced considerably the flowability of the particles containing oil. The dispersion behavior of the powders with higher lipid content could be correlated with the Hausner Number. A pre-agglomeration step favored the blend of the more cohesive powders producing larger and more resistant agglomerates.     

Complex processing of fluorine-containing wastes of fluorite ores

The possibility of processing fluorine-containing wastes of fluorite ore, which include fluorite, calcite, quartz, and anorthite, has been investigated. A manufacturing flow chart of the complex processing of the ore waste materials with the production of sodium fluoride, alumina, soda ash, and raw materials suitable for the production of Portland cement and wollastonite is suggested.     

Removal of impurities from liquid solutions by vacuum desorption with solvent evaporation

Mass transfer with solvent evaporation in the vapor-liquid two-phase film evaporators used for the removal of undesirable impurities from liquid solutions at low pressure is studied. The average concentrations of solution components in the falling liquid film are determined. The most efficient operating conditions for impurity removal, in which the resistance to mass transfer is concentrated in the liquid phase, are found. Original Russian Text ? V.N. Babak, T.B. Babak, L.P. Kholpanov, 2008, published in Teoreticheskie Osnovy Khimicheskoi Tekhnologii, 2008, Vol. 42, No. 6, pp. 654–670.     

Integrated carbon nanotube field emission differential amplifier: Modeling and measurement of the common-mode rejection ratio

A novel integrated vacuum field emission (VFE) differential amplifier (diff-amp) utilizing carbon nanotube (CNT) emitters has been developed. A dual-mask microfabrication process was employed to achieve a VFE diff-amp by integrating identical CNT VFE transistors with built-in split gates and integrated anodes. The identical pair of triode amplifiers was well-matched in their device characteristics. The measured ac small-signal characteristics of the diff-amp showed a common-mode-rejection ratio (CMRR) of ~ 320 (~ 50 dB). The proposed analytical model of the CMRR was verified to be in good agreement with the experimental data. The successful implementation of the CNT diff-amp demonstrates a new way to achieve temperature and radiation tolerant VFE integrated microelectronics.     

Ionothermal synthesis of a three-dimensional zinc phosphate with DFT topology using unstable deep-eutectic solvent as template-delivery agent

A three-dimensional zinc phosphate compound with DFT topology, designated as ZnPO₄-EU1, has been synthesized by an ionothermal approach from the system HF-ZnO–P₂O₅-choline chloride-imidazolidone. Ethylenediamine, derived from decomposition of the imidazolidone component of the deep-eutectic solvent (DES) itself, is delivered to the synthesis and serves as an appropriate template for ZnPO₄-EU1. Experiments in which the synthesis conditions were varied showed that ZnPO₄-EU1 may be prepared over a wide molar ratio of P/Zn = 0.55–13.0. Powder X-ray diffraction patterns have been obtained at intervals to track the crystallization process of this material. The experimental data show that Zn₃(PO₄)₂ · 4H₂O (a dense phase) was first isolated from the DES after reaction for 1 h. Subsequently, the pure phase of ZnPO₄-EU1 was obtained with increasing crystallization time from 12 h to 72 h. The experimental results show that the nucleation and crystallization take place with relatively low levels of solvent degradation, demonstrating that zinc phosphate with a three-dimensional framework can be synthesized by in situ generation of an appropriate template using an unstable DES at high temperatures (150–200 °C).     

Investigation of the structure and properties of modified Armenian minerals for polymer-based composites

The results of investigation of the modification of the Armenian minerals with fluorine-containing oligomers show that a modified product appears when the mineral fillers are treated with fluoroalkanes. The product preserves the structure of the fillers with a “grafted” fluoroalkane layer in which chlorine atoms locate mainly over their periphery. The composite materials based on heterochained polymers and the modified fillers possess a stronger wear resistance and a low friction coefficient.     

Single and matrix HgCdTe photovoltaic detectors

The recent researches and technological developments of middle and long wavelength infrared HgCdTe photovoltaic detectors are presented. Structure, topology, design and performance of HgCdTe photodiodes, silicon readout electronics, Focal Plane Arrays both staring and time delay and integration types, thermal imagers are discussed. Negative differential conductance, bistability and high frequency oscillations under background infrared radiation in HgCdTe photodiodes are reported.     

Rehabilitation of the radioactively contaminated objects and territory of the Russian Science Center Kurchatov Institute

This article is devoted to work done in 2002–2006 as part of the unified project Reabilitatsiya to rehabilitate radiation hazardous objects and sections of the radioactively contaminated territory of the Russian Science Center Kurchatov Institute. The main objects of the rehabilitation work were old storage sites built for radioactive wastes on the territory of the Institute when military and civilian nuclear technologies were under development. The structural features of the storage sites, including the volumes and characteristics of the wastes stored, are presented. The salient aspects of the disposal sites, taken into account during the rehabilitation work, are discussed. The organization of the rehabilitation operations and the sequence in which they are performed, the special features of the technical design solutions used, the technological methods, and ways for conducting the work are described. __________ Translated from Atomnaya énergiya, Vol. 102, No. 5, pp. 300–306, May, 2007.     

Architectural,construction and environmental matters of Bahrain's International Formula 1 Circuit

The Bahrain International Circuit (BIC) is considered as one of the best international racing car track in terms of technical aspects and architectural quality. Two Formula 1 races have been hosted in the Kingdom of Bahrain, in 2004 and 2005, at BIC. The BIC had recently won the award of the best international racing car circuit.