Final Drying of Whole Milk Powder in Vibrated-Fluidized Beds

Vibro-fluidized beds are widely used in drying sticky powders and agglomerated materials as milk powder. Using a vibro-fluidized laboratory scale dryer, this work is aiming at analyzing preliminarily the effect of its operational variables on the drying kinetics and characteristics of whole milk powder. The full-factorial design technique with three replications at the central point has been employed to generate data and correlations to quantify the effect of inlet air temperature, air flow rate, and vibration bed amplitude on the drying curves and the milk powder properties related to its faster reconstitution in water (as tapped density, Hausner cohesion ratio, agglomerate size distribution, and internal pore concentration). Results obtained are analyzed and discussed to identify the adequate operation condition for final drying whole milk powder in vibro-fluidized beds, assuring a high product quality.     

Effects of solid retention time on the performance of submerged anoxic/oxic membrane bioreactor.

In this study, four similar bench-scale submerged Anoxic/Oxic Membrane Bioreactors (MBR) were used simultaneously to investigate the effects of solids retention time (SRT) on organic and nitrogen removal in MBR for treating domestic wastewater. COD removal efficiencies in all reactors were consistently above 94% under steady state conditions. Complete conversion of NH(4+)-N to NO(3-)-N was readily achieved over a feed NH(4+)-N concentration range of 30 to 50 mg/L. It was also observed that SRT did not significantly affect the nitrification in the MBR systems investigated. The average denitrification efficiencies for the 3, 5, 10 and 20 days SRT operations were 43.9, 32.6, 47.5 and 66.5%, respectively. In general, the average effluent nitrogen concentrations, which were mainly nitrate, were about 22.2, 27.6, 21.7 and 13.9 mg/L for the 3, 5, 10 and 20 days SRT systems, respectively. The rate of membrane fouling at 3 days SRT operation was more rapid than that observed at 5 days SRT. No fouling was noted in the 10 days and 20 days SRT systems during the entire period of study.     

A study on hydrogen storage by use of cryoadsorbents

This paper reports investigations on the techniques and economics of hydrogen storage by means of cryoadsorption. Also a comparison with alternative storage methods is included. The hydrogen storage capacity of several adsorbents in the temperature range 65–150 K has been investigated experimentally. Based on these data, economics and operating conditions for minimum total costs of the system are calculated. Utilization-factor and capacity-factor parameters are shown to be decisive for outlining the favourable ranges of application for competitive hydrogen storage methods.     

Computer aided design and new manufacturing methods for electronic materials

The world-wide sales for silicon integrated circuits totalled some £3,500M in 1980. The high growth rate of the industry is generated by high levels of investment in research, development and capital equipment leading to rapid innovation in design and manufacturing methods. This article concentrates on the increasing use of computers in the design process, new design concepts and the efforts to make the components within the silicon chip even smaller.     

The Aleph data acquisition system

Aleph is one of the four large high-energy physics experiments being completed for the LEP (Large Electron Positron) accelerator at CERN. Several hundred thousand detector elements deliver some 500 Mbytes of raw data per second. The author briefly describes the accelerator and the Aleph detector. He then discusses the design and implementation of the multilevel real-time data reduction and acquisition system, covering the requirements, the readout architecture, its implementation, data reduction, aspects of the detector-specific front-end electronics, and Aleph's present status and performance     

Approximate channel identification via δ‐signed correlation

A method of approximate channel identification is proposed that is based on a simplification of the correlation estimator. Despite the numerical simplification (no multiplications or additions are required, only comparisons and an accumulator), the performance of the proposed estimator is not significantly worse than that of the standard correlation estimator. A free (user selectable) parameter moves ‘smoothly’ from a situation with small sum‐squared channel estimation error but hard‐to‐identify channel peaks, to one with a larger sum‐squared estimation error but easy‐to‐identify channel peaks. The proposed estimator is shown to be biased and its behaviour is analysed in a number of situations. Applications of the proposed estimator to sparsity detection, symbol timing recovery and to the initialization of blind equalizers are suggested. Copyright © 2002 John Wiley & Sons, Ltd.     

Performance of a non‐load‐bearing steel stud gypsum board wall assembly: Experiments and modelling

A gypsum wall assembly was exposed to an intense real‐scale compartment fire. For the wall assembly, temperatures were measured at the exposed face, within the stud cavity, and at the unexposed face during the fire exposure. Total heat flux gauges were used to measure the temporal variation of the energy incident on the walls, and cameras, both visual and infrared, were used to image the unexposed face of the wall assembly during the fire exposure. The behaviour of the wall assembly under the fire load is discussed as are current model results for a simulation of the fire test. Copyright © 2006 John Wiley & Sons, Ltd.     

Tensions in water management: Dutch tradition and European policy.

Present-day worldwide water problems require new management tools and sustainable system innovations. At Delft University of Technology research is being carried out into water resources and management development aimed at forming such tools and innovations, focused on Integrated River Basin Management (IRBM). One of the case-studies deals with Dutch water management and technology in the context of European IRBM in the form of the 2000 Water Frame Directive. The Netherlands experience many water problems and European IRBM could bring help by offering a framework for both international cooperation and technological innovations. To work as an adequate management tool European IRBM should be tailored to the Dutch water tradition, which recently culminated in Integrated Water Management. Both approaches are in some respects contradicting. Europe pursues, for example, centralized control; while the Dutch have their strongly water boards based decentralized administration. The tensions between both approaches require mutual adaptation, for which the concept of subsidiarity might offer points of departure. This paper describes the first results of the case-research into Dutch water management and technology in the context of Europe as well as the backgrounds and the set-up of the research as a whole.