聚碳硅烷的分子量分布与可纺性研究

阐述了聚碳烷的合成及其分子量分布，讨论了高低分子含量对聚碳硅烷熔点及可纺性的影响，而且提出了分子量分布的控制标准与方法。     

工业CT技术在铸造技术中的应用

介绍了工业ＣＴ在铸件的缺陷探伤，壁厚测量以及铸造工艺控制中的应用。     

反应自生Al_3Ni－Al_2O_3－Al复合材料

通过热力学计算，选择Ｎｉ_２Ｏ_３粉末作原材料，采用反应挤压铸造方法实现了Ａｌ与Ｎｉ２Ｏ３直接压铸反应合成Ａｌ３Ｎｉ－Ａｌ２Ｏ３－Ａｌ原位复合材料。研究了压铸工艺参数和预制块中纯Ａｌ粉的含量对反应合成复合材料过程的影响，并对反应机理做了较深入的分析。结果表明，Ｎｉ２Ｏ３与Ａｌ的反应是为高放热反应，反应是爆发式的，通过调整预制块中Ａｌ粉的体积分数控制了反应的剧烈程度，并能获得不同组成和基体含量的复合材料。对反应机理的分析表明，在Ａｌ足量的情况下，Ｎｉ２Ｏ３与Ａｌ反应合成复合材料分为两个过程，一是反应过程，即Ｎｉ２Ｏ３＋Ａｌ→Ａｌ２Ｏ３＋［Ｎｉ］；二是凝固过程，即反应后多余的Ａｌ与反应生成的［Ｎｉ］在随后冷却中的凝固过程，最终形成Ａｌ３Ｎｉ＋α－Ａｌ２Ｏ３＋Ａｌ复合材料。     

GaAs Mach－Zehnder型光波导开关／调制器

采用非对称Ｘ结耦合器代替传统的Ｙ分支器，研制了ＧａＡｓＭａｃｈ－Ｚｅｈｎｄｅｒ型２×２光开光，得到了小于－２２．４ｄＢ的串音比和１２Ｖ左右的开关电压，器件的波导传输损耗小于７ｄＢ／ｃｍ。预计该器件可广泛应用于ＧａＡｓ开关列阵及高速光调制等领域。     

弹丸外弹道优化设计初始点的选取

在弹丸外弹道优化设计中,需对优化设计变量赋于初始值.初始值选取得如何,对整个优化计算所耗机时、迭代点收敛到哪个极值点上等等,影响很大.该文对初始值的选取原则、选取方法等作了讨论,所得结果也可作为对弹丸主要结构参数选优的预估.     

Simulation of the pressure set-point change transient with the Kuosheng plant analyzer

The purpose of this paper is to simulate the pressure set-point change transient with the Kuosheng plant analyzer. The Kuosheng plant analyzer was developed for the Kuosheng nuclear power station based on the boiling water reactor plant analyzer of the Brookhaven National Laboratory and the Chinshan plant analyzer of the Taiwan Power Co. First, the pressure control system (PCS) model was verified on a stand-alone basis, with the sensed dome pressure test signal as the input variable. Then, a transient induced by a step change in the pressure set-point was simulated with the Kuosheng plant analyzer and compared with the test data. The predicted results of the main system variables showed good agreement with the test data-within 8% of the maximum relative deviation. In addition, the PCS performance of the Kuosheng nuclear power station was analyzed.     

Multiple respiratory gas monitoring causes changes of inspired oxygen concentration in closed anesthesia system

This case report describes an accessory hepatic duct (AHD) identified by intraoperative cholangiography during excisional surgery of a choledochal cyst (CC). The accessory duct was divided and reconstructed successfully to the Roux-en-Y jejunal loop. The postoperative course was uneventful, and follow-up abdominal sonography revealed neither evidence of biliary tract obstruction nor atrophic changes of the liver. It is advocated that an AHD should be meticulously reconstructed if it is divided during excisional surgery of a CC.     

地面驱动单螺杆泵杆柱的组合设计

根据地面驱动单螺杆泵的工作特点，分析了传递动力的抽油杯柱受力状况，认为抽油杆柱受复合载荷的作用，在承受扭矩的同时承受较大的轴向力，给出了各种载荷的计算方法。由第四强度理论，提出了把抽油杯柱设计成两级杆柱的等强度组合设计方法，即先按要求及标准确定两级杆柱的直径和长度，然后扶强度条件进行校核。根据油田的实际情况，编制了抽油杆柱电算程序，并给出了设计训一算实例。