映射半解析边界元法解瞬态弹性动力问题的有关问题

提出了映射半解析边界元法解百轴对称瞬态弹性动力问题时存在解析方向不能正确反映波的传播现象的问题，产生该问题的原因和如何解决该问题的建议。     

二元复合驱采出液矿场处理试验

利用研制的二元复合驱采出液矿场处理装置，对辽河油田兴28块兴191井采出液进行了矿场处理试验。结果表明，采用适宜的破乳剂及处理工艺技术，可以使矿场采出液处理达到净化油含水≤0．5％的指标。     

The maximum bit rates of soliton communication systems with lumpedamplifiers and filters in different distances

The maximum bit rate of a soliton communication system with lumped amplifiers and optical filters is considered. When the dispersion of the fiber varies from one amplifier spacing to another amplifier spacing, the maximum bit rate is significantly reduced. To overcome the effect, the amplitude of the soliton is amplified so that it is still the average soliton corresponding to the fiber dispersion for an amplifier spacing. Thus, the maximum bit rate is only slightly less than that without the dispersion variations. For a given distance, the maximum bit rate limited by the stability and soliton interaction is obtained. The result is compared with that limited by the Gordon-Haus effect. For shorter transmission distance, the maximum bit rate is limited by the stability and soliton interaction. For longer transmission distance, the maximum bit rate is limited by the Gordon-Haus effect     

柴油机低频排气噪声规律分析

针对柴油机（4－85）低频排气噪声，对其产生机理、规律及其影响因素等作了理论计算、分析及实验。对低频排气噪声信号进行频域分析后可知，其主要由一系列离散的谐波组成，是以柴油机点火频率为基频的一种类周期性噪声，有可能应用有源噪声控制技术。     

填料萃取塔液泛速度的计算

介绍了三种有代表性的填料萃取塔的液泛速度计算公式，并通过它们用于三种典型的液-液实验体系和两种不同填料的计算结果的比较，对这些公式的适用范围进行了讨论。     

LaCrMnNiO系热敏陶瓷的微观结构控制

通过对不同配方、工艺下的ＬａＣｒＭｎＮｉＯ系热敏陶瓷的微观结构研究，指出材料的相组成对其宏观电性能的影响，并提出了通过复合工艺利用“过渡相”的形成，对材料的“最终相”加以控制的方法。文中列出了使用ＸＲＤ及ＸＰＳ手段对材料微观结构的分析结果及有关电性能的测试数据。     

欧阳海水电站调速器改造

为适应电力系统发展的要求,欧阳海水电站在资金有限的情况下分期分批对全站监控系统、调速器、励磁系统、空压机系统、水系统进行了改造。文章介绍了调速器功能特点、运行状况以及存在的问题和处理方法。     

石油钻机提升系统穿绳方法研究

目前国内外钻机大绳一般采用顺穿法或花穿法。分析了2种穿绳方法的受力特点,大绳顺穿时游车的受力不平衡,会发生倾斜和摆动;采用大绳花穿方法,避免了游车的倾斜和摆动,但造成大绳入轮槽的倾角大,大绳易脱槽。顺穿法一般在电动钻机上采用,主要考虑到电控操作提升系统比较平稳;花穿法一般在机械钻机上使用,以受力平衡来缓解气控操作带来的冲击载荷的影响。为了克服这2种穿绳方法的不足,提出了两行双联滑轮组顺穿法和双联滑轮组顺穿法,可以提高安全性,减少磨损。     

Separating inviscid flows

Summary The separating flow of an inviscid fluid is not only a limit solution of the steady separating, laminar fluid flow at high values of the Reynolds number but it is also part of its structure (Smith [1], [2]). This work aims at reexamining the separating flow of inviscid fluid past a bluff body which is fixed in an otherwise uniform stream of fluid. For the purpose of this paper we will assume that the bluff body is a circular cylinder but the theory is applicable to bodies of any shape. It is further assumed that the fluid is in steady two-dimensional motion and is inviscid and of constant density. The flow structure is assumed to consist of a separated flow region, caviting flows in which there exists a free surface on which the pressure is constant, and a wake. A twin spiral vortex model is used in order to determine the shape of the free streamline. Based on the free streamline theory the problem reduces to solving a mixed boundary value problem and a Hilbert solution for the inverse problem in the auxiliary plane is obtained. When we consider the flow in the physical plane the problem is transformed into a direct problem in which the geometry of the solid body is given in advance. We assume that the separation is smooth and thus the curvature of the free streamline at the point of free detachment be equal to that of the body surface. A numerical method for solving the two-dimensional potential flows past arbitrarily shaped curved bluff bodies is developed.When the cavitation number is zero the angle of separation is approximately 55° and the computed results predict that the position of the separation point will move backward as the cavition number increases. The relationships between the drag coefficient, and the width and length of the cavity is determined and is found to be in very good agreement with the predictions of Smith [1].