Analysis of Indentation Crack as a Wedge-Loaded Half-Penny Crack

Surface cracks produced by indentation with a Vickers indenter were modeled as half-penny cracks extended by symmetric disk-shaped wedges. The wedge diameter was assumed to be equal to the hemispherical plastic zone size, and the wedge thickness was calculated by equating the wedge volume to the hardness-impression volume. The resulting equilibrium relation between the indentation load and the radius of the half-penny crack is in good quantitative agreement with similar relations obtained from fracture toughness calibration.     

Production of propylene glycol fatty acid monoesters by lipase-catalyzed reactions in organic solvents

Fatty acid monoesters of propylene glycol (1,2-propanediol) are good water-in-oil emulsifiers. These esters were synthesized enzymatically to overcome the problems associated with chemical processes. APseudomonas lipase was added to reaction mixtures containing propylene glycol and various acyl donors (fatty acids, fatty acid ethyl esters, fatty acid anhydrides and triglycerides) in organic solvents, and the mixtures were shaken at 30°C. The products were analyzed by gas chromatography. The yield of monoesters was affected by the acyl donors, organic solvents, temperature, water content, pH memory and reaction time. The anhydrous (lyophilized) enzyme and fatty acid anhydrides were best for monoester production. The optimum pH ranges were 4–5 and 8–10. The yields of propylene glycol monolaurate, monomyristate, monopalmitate, monostearate and monooleate with 50 mM fatty acid anhydrides as acyl donors were 97.2, 79.6, 83.7, 89.7 and 93.4 mM, respectively; those with 50 mM fatty acids as acyl donors were 37.3, 28.7, 28.7, 35.3 and 36.2 mM, respectively. The yields of propylene glycol monopalmitate, monostearate and monooleate with 50 mM triglycerides as acyl donors were 87.4, 65.1 and 83.2 mM, respectively.     

Engineering a pharmacologically superior form of leptin for the treatment of obesity

Leptin plays a central role in the homeostasis of body weight through its regulatory effects on appetite and energy expenditure, yet in trials as a therapeutic agent for the treatment of obesity in humans it has been disappointing. The poor clinical efficacy of leptin results from its short circulating half-life, low potency and poor solubility, necessitating large and frequent doses to obtain even modest clinical benefit. Engineered Fc-leptin immunofusins, consisting of the Fc fragment of an immunoglobulin gamma chain followed by leptin, exhibit improved pharmacological properties with very consistent and potent biological activities. Furthermore, in extending the circulating half-life of the protein in vivo from a few minutes for leptin to many hours for Fc-leptin, these proteins have the potential to reduce drastically the dosage and frequency of administration required to obtain clinical benefit. The results of this study show that the engineered leptin immunofusins described here have significantly enhanced pharmacological properties in comparison with the recombinant leptin that was used in clinical trials. As such, they could represent an important step towards a therapeutically superior form of leptin if the disappointing performance of leptin in early clinical trials was due to its poor pharmacological properties rather than any conceptual weakness in the strategy of using leptin for the treatment of obesity and its related disorders.     

Betweenness estimation in OLSR-based multi-hop networks for distributed filtering

In traditional networks special efforts are put to secure the perimeter with firewalls: particular routers that analyze and filter the traffic to separate zones with different levels of trust. In wireless multi-hop networks the perimeter is a concept extremely hard to identify, thus, it is much more effective to enforce control on the nodes that will route more traffic. But traffic filtering and traffic analysis are costly activities for the limited resources of mesh nodes, so a trade-off must be reached limiting the number of nodes that enforce them. This work shows how, using the OLSR protocol, the centrality of groups of nodes with reference to traffic can be estimated with high accuracy independently of the network topology or size. We also show how this approach greatly limits the impact of an attack to the network using a number of firewalls that is only a fraction of the available nodes.     

Geochemical implications of trace elements and sulfur in the saturate, aromatic and resin fractions of crude oil from the Mara and Mara Oeste fields, Venezuela

Ten trace elements (Cr, Zn, Fe, Mn, Cu, Co, Ni, Mo, V and Sr) and sulfur were determined in the saturate, aromatic and resin fractions of 15 crude oils from Mara (DM) and Mara Oeste (DMO) fields of the Maracaibo Basin, Venezuela. The oils studied are classified as unaltered or altered by biodegradation. In the altered oil, the depletion of n-alkanes, the absence of isoprenoids and the presence of steranes and hopanes unaltered by biodegradation are indicative of moderate biodegradation. The elements Zn, Fe, Mn, Cu, Ni, and Sr were detected in the saturated hydrocarbon fraction; Cr and V were detected in the aromatic fraction in addition to the above elements; whereas the elements detected for the resin fraction were Cr, Zn, Fe, Cu, Ni, Mo, V, and Sr. Co was not detected in any fractions of the oils analyzed. Sulfur was found in all fractions of the oils studied. It was proposed that Fe, Zn, Sr, and Mn could have entered the oil during migration or Fe, Zn and Mn as pollutants during oil extraction. Cr and Cu may be of biological origin and Mo could be incorporated into the reservoir through bacteria. Only S, V, and Ni in the resin fractions can be used as indicators of the origin and correlation of Mara and Mara Oeste oils. Based on the results obtained in this work, it can be established that the V/(V+Ni) ratio in the resin fraction can be used as a correlation parameter, for these oils.     

A simplified method for analyzing mold filling dynamics. Part II: Extensions and comparisons with experiment

A dimensional analysis based on four parameters has been developed previously to predict injection pressure; clamp force, and bulk temperature for the injection molding of amorphous materials in center-gated disk-shaped cavities. In this paper geometric and semicrystalline-materials approximations are introduced and tested for extending the previous analysis to include multigated thin cavities and semicrystalline materials. The combination of these approximations and the previous analysis, known hereafter as the Radial Flow Method (RFM), greatly simplifies the analysis of mold filling. The geometric approximation, which is based on a simple model for the axial stress distribution in the cavity, is shown to give reasonable predictions when compared with experimental data and a numerical two-directional flow simulation for the filling of an off-center-gated rectangular cavity with acrylonitrilebutadiene-styrene copolymer (ABS). The semicrystallinematerials approximation, in which heat capacity and viscosity changes during crystallization are neglected, is shown to give good agreement with experimental data for the filling of a center-gated disk-shaped cavity with polypropylene. As an illustration, the Radial Flow Method is used to analyze the molding of a large, thin-wall automobile interior trim panel. The inlet melt temperature, mold-wall temperature, part thickness, injection rate, viscosity and gate locations are varied in a series of calculations to determine the relative effectiveness of these variables in lowering the injection pressure and Clamp force. The results obtained with the Radial Flow Method are in good agreement with those obtained by a finiteelement simulation of two-directional flow.     

Monitoring the cure of unsaturated polyester resins by pressure DSC and FTIR-PLC

A high pressure differential scanning calorimeter (DSC) and a Fourier transform infrared (FTIR) spectrometer with a prism liquid cell (PLC) were used to monitor the reaction kinetics of styrene-unsaturated polyester resins at elevated curing temperatures and pressures. The thermal method is easy to perform but provides only an overall reaction exotherm. The spectroscopic method can detect the detailed reaction mechanism of copolymerizations. It is, however, less quantitative and the calculation is much more time-consuming compared to the thermal analysis. Reactions of two unsaturated polyester resins with different molecular structure were measured by these two methods. Results showed that applying cure pressure on unsaturated polyester resins reduced the reaction rate but increased the final conversion. The styrene reaction was enhanced more than the polyester reaction at high curing temperatures.     

Insecticidal Effects of Organotin(IV) Compounds on Plutella Xylostella (L.) Larvae. II. Inhibitory Potencies Against Acetylcholinesterase and Evidence for Synergism in Tests With Bacillus Thuringiensis(BER.) and Malathion

Features of pesticide synergism and acetylcholinesterase (AChE) inhibition (in vitro) were studied using a selected range of organotin compounds against the early 4th instar larvae of a highly resistant strain of the diamondback moth (DBM), Plutella xylostella, a major universal pest of cruciferous vegetables.Fourteen triorganotin compounds were evaluated for their ability to enhance the toxicity of the microbial insecticide, Bacillus thuringiensis (BT) and of the commercial insecticide, Malathion to Plutella xylostella larvae. Supplemental synergism was observed with triphenyl- and tricyclopentyltin hydroxides in combinations with Bacillus thuringiensis. Increased synergism was observed with an increase in the number of cyclopentyl groups on tin in the mixed series, Cyp(n) Ph(3-n) SnX, where X = OH, and 1-(1,2,4-triazolyl). The combination of (p-chlorophenyl)diphenyltin N,N-dimethyldithiocarbamate at LD(10) and LD(25) concentrations with sublethal concentrations of Malathion as well as of tricyclohexyltin methanesulphonate at the 0.01% (w/v) concentration with Malathion exerted strong synergistic effects (supplemental synergism) with toxicity index (T.I) values of 7.2, 19.8 and 10.1, respectively.Studies on the in vitro inhibition of acetylcholinesterase prepared from the DBM larvae showed that while most of the triorganotin Compounds tested were without effect on the enzyme, compounds containing the thiocarbamylacetate or the dithiocarbamylacetate moieties demonstrated appreciable levels of inhibition, being comparable in efficacy to commercial grades of Malathion and Methomyl.     

Developmental variations in plasma leptin,leptin soluble receptor and their molar ratio in healthy infants

Background  

Leptin and its soluble receptor (sOB-R) are important to regulation of body composition but there are no data on the developmental variations in these plasma variables and their relationship with body composition measurements,     

Mandibular gland components of european and africanized honey bee queens (Apis mellifera L.)

The composition of the five-component honey bee queen mandibular gland pheromone (QMP) of mated European honey bee queens was compared to those of virgin and drone-laying (i.e., laying only haploid unfertilized eggs that develop into males), European queens and Africanized mated queens. QMP of mated European queens showed significantly greater quantities of individual components than all queen types compared, except for a significantly greater quantity of 9-hydroxy-(E)-2-decenoic acid (9-HDA) found in Africanized queens. Glands of European drone-laying queens contained quantities intermediate between virgin and mated queens, reflecting their intermediate reproductive state and age. QMP ontogeny shifts from a high proportion of 9-keto-(E)-2-decenoic acid (ODA) in young unmated queens to roughly equal proportions of ODA and 9-HDA in mated queens. A biosynthetic shift occurs after mating that results in a greater proportion of 9-HDA, methylp-hydroxybenzoate (HOB), and 4-hydroxy-3-methoxyphenylethanol (HVA) production, accompanied by a decreased proportion of ODA. Africanized QMP proportions of ODA and 9-HDA were significantly different from European queens. A quantitative definition of a queen equivalent of QMP is proposed for the various queen types, and a standard queen equivalent for mated European honeybee queen mandibular gland pheromone is adopted as 200µg ODA, 80µg 9-HDA, 20µg HOB, and 2 µg HVA.