Synthesis and characterization of a novel proton‐exchange membrane for fuel cells operating at high temperatures and low humidities

The synthesis of a p‐toluidine/formaldehyde (PTF) resin was performed, and the effects of the molar ratio of the individual monomers and the polymerization conditions on the structure of the PTF resin were studied. Fourier transform infrared and ¹³C‐NMR spectra were used to characterize the PTF. Wide‐angle X‐ray diffraction patterns revealed the crystalline structures of various PTFs. Polarized optical microscopy revealed that the molar ratio of the monomers had a strong effect on the crystalline morphologies. A longer polymerization time turned out a polymer with a higher intrinsic viscosity and molecular weight, which led to differences in the proton conductivity. All of the PTFs showed a higher proton conductivity than a commercial Nafion membrane at 90–100°C and 0% relative humidity. The proton conductivity of the PTF series could be improved by sulfonation with sulfuric acid and could be maintained after blending with polyurethane. Pure methanol could be used as a fuel source because of the insolubility and nonwetting properties of PTF in methanol to increase the output current density for a PTF membrane electrode assembly. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Differentially coherent code acquisition in the MIMO-aided multi-carrier DS-CDMA downlink

Both differentially coherent and non-coherent code acquisition schemes designed for the multiple-input multiple-output (MIMO)-aided multi-carrier (MC)-DS-CDMA downlink are analysed, when communicating over uncorrelated Rayleigh channels. The attainable mean acquisition time (MAT) performance is studied as a function of both the number of multiple transmit/multiple receive antennas and that of the number of subcarriers. It is demonstrated that in contrast to the expectations, when the number of multiple transmit antennas and/or that of the subcarriers is increased in both the differentially coherent and the non-coherent code acquisition scenarios, the achievable MAT deteriorates over the entire signal-to-interference plus noise ratio (SINR) per chip (E_c/I_o) range considered, except for the scenario of single-carrier (SC)-DS-CDMA using P = 2 transmit antennas and R = 1 receive antenna. As expected, the degree of performance degradation depends upon the specific scheme and the E_c/I_o ratio considered, although paradoxically, the correctly synchronised MIMO-aided system is capable of attaining its target bit error ratio performance at reduced SINR values.     

Effects of alloying elements on fracture toughness in the transition temperature region of base metals and simulated heat-affected zones of Mn-Mo-Ni low-alloy steels

This study is concerned with the effects of alloying elements on fracture toughness in the transition temperature region of base metals and heat-affected zones (HAZs) of Mn-Mo-Ni low-alloy steels. Three kinds of steels whose compositions were varied from the composition specification of SA 508 steel (grade 3) were fabricated by vacuum-induction melting and heat treatment, and their fracture toughness was examined using an ASTM E1921 standard test method. In the steels that have decreased C and increased Mo and Ni content, the number of fine M₂C carbides was greatly increased and the number of coarse M₃C carbides was decreased, thereby leading to the simultaneous improvement of tensile properties and fracture toughness. Brittle martensite-austenite (M-A) constituents were also formed in these steels during cooling, but did not deteriorate fracture toughness because they were decomposed to ferrite and fine carbides after tempering. Their simulated HAZs also had sufficient impact toughness after postweld heat treatment. These findings indicated that the reduction in C content to inhibit the formation of coarse cementite and to improve toughness and the increase in Mo and Ni to prevent the reduction in hardenability and to precipitate fine M₂C carbides were useful ways to improve simultaneously the tensile and fracture properties of the HAZs as well as the base metals.     

Motion based object tracking with mobile camera

An efficient algorithm which detects and tracks a moving object is proposed. The global motion energy caused by camera movement is eliminated by finding the maximal matching position with the cross-correlation value between two consecutive frames using the spiral scanning technique. The region of a moving object is segmented exactly by combining the results of the temporal derivatives and edge map from one image, and the actual centroid of the moving object is determined as the mid-point of the cumulative distribution of the projection profile of the region     

Signal tracking method of GNSS receivers for spinning vehicles

A signal tracking method of GNSS receivers for spinning vehicles is proposed in order to eliminate the influence of spinning to the GNSS signal of a vehicle. In the proposed method, a rotation tracking loop is added into the carrier tracking loop of a conventional GNSS receiver. The proposed method was verified through computer simulations and an experiment for live GPS signals. The results show that the proposed method gives an accurate tracking performance.     

An adaptive genetic algorithm for the time dependent inventory routing problem

In this paper we propose an adaptive genetic algorithm that produces good quality solutions to the time dependent inventory routing problem (TDIRP) in which inventory control and time dependent vehicle routing decisions for a set of retailers are made simultaneously over a specific planning horizon. This work is motivated by the effect of dynamic traffic conditions in an urban context and the resulting inventory and transportation costs. We provide a mixed integer programming formulation for TDIRP. Since finding the optimal solutions for TDIRP is a NP-hard problem, an adaptive genetic algorithm is applied. We develop new genetic representation and design suitable crossover and mutation operators for the improvement phase. We use adaptive genetic operator proposed by Yun and Gen (Fuzzy Optim Decis Mak 2(2):161–175, 2003) for the automatic setting of the genetic parameter values. The comparison of results shows the significance of the designed AGA and demonstrates the capability of reaching solutions within 0.5 % of the optimum on sets of test problems.     

Eddy characteristics on mass transfer close to free interface

The velocity fluctuations in the immediate vicinity of a free interface were measured with a hot film anemometer. And mass transfer rates and eddy exposure times were analyzed by using the method of deterministic approach. These mass transfer rates were compared with the mass transfer rates by means of concentration measurements in the air-water system. The eddy exposure time distributions obtained from velocity data were skewed toward the lower time value. The contribution of eddies wi:h small exposure time was increased as the liquid became more turbulent. The mass transfer rates were mainly contributed by the Prandtl size eddies and even larger eddies. The mass transfer predictions by the single eddy model employing a deterministic method were in good agreement with the experimental results by independent measurements of concentration.     

Hydrodynamic characteristics of a FCC regenerator

The hydrodynamic and gas mixing characteristics have been determined in a FCC regenerator (0.48 m I.D.x3.4 m high) with FCC particles. Solids holdup in the dense bed decreases with increasing gas velocity, but it increases in the freeboard region. The bubble/void fraction increases with an increase along the bed height at a given gas velocity and increases with increasing gas velocity at a constant bed height. Backmixed tracer gas at the wall region is higher than that at the center region of the bed. The gas backmixing coefficient decreases with increasing gas velocity.     

Diffusional interference in liquid phase counter-adsorptions

A surface diffusion mocel with diffusional interference has been presented for the analysis of multicomponent adsorption of phenols by activated carbon. Surface diffusion coefficients for multicomponent adsorptions were estimated from the relationship between. the surface diffusion coefficient of each species and the surface coverage. The diffusional interference coefficients, W_ij, was determined from experimental counter-adsorption data. The numerical values of W_ij were in the range of 0.4–0.9, which show that the introduction of diffusional interference is necessary to analyze multicomponent counter-adsorptions properly. The proposed model successfully simulates the behaviour of phenols-activated carbon system in a batch adsorber.