Comfort limits for asymmetric thermal radiation

Groups of 32 and 16 subjects of both sexes were exposed in an environmental chamber to radiant asymmetry caused by a cool wall, a warm wall, and a cool ceiling. Each subject was tested individually while seated and clothed at 0.6 clo. During each 3.5-hour experiment the subject was exposed to six radiant temperature asymmetries. He was asked whether and where he experienced any local cool or warm sensation, and whether it was felt to be uncomfortable. During the entire experiment he was kept thermally neutral by changing the air temperature according to his wishes.For cool walls, warm walls, and cool ceilings curves have been established showing the percentage of dissatisfied subjects as a function of the radiant asymmetry. Radiant asymmetry at a warm wall caused less discomfort than a cool wall. A cool ceiling caused less discomfort than a warm ceiling. Accepting that 5% of the subjects may feel uncomfortable. a radiant temperature asymmetry of 10°C is allowable at a cool wall, 23°C at a warm wall, and 14°C under a cool ceiling. A previous study showed that 4°C is allowable under a warm ceiling. Radiant asymmetry had no significant impact on the operative temperatures preferred by the subjects. No significant differences were observed between the responses of men and women exposed to radiant asymmetry.     

Criteria for evaluation of the hardening factor of machine parts

V. Ya. Chubar' Zaporozhe Machine Building Institute. Translated from Problemy Prochnosti, No. 3, pp. 62–65, March, 1989.     

Toughening of Dental Porcelain by Tetragonal ZrO2 Additions

The effect on mechanical behavior of ZrO₂ additions to a dental porcelain was investigated. The ZrO₂ was introduced into the glassy matrix phase of the porcelain by refritting the all-glass porcelain constituent. X-ray diffraction indicated that a sizeable fraction of the ZrO₂ was retained in the tetragonal form after the porcelain was fired. Zirconia additions to the porcelain produced substantial improvements in fracture toughness, strength, and thermal shock resistance.     

Mathematisch-statistische Simulierung der mechanischen Eigenschaften von Bauspanplatten

Physical and process manufacturing factors affecting the properties of particleboard were examined and mathematical relationships were derived to predict board modulus of elasticity and internal bond. The equations, derived from a series of previous laboratory investigations, allow the simulation of the effects of various process conditions on final properties of 1/2-inch (12-mm) boards.     

Indoor body-area channel model for narrowband communications

Using wireless sensors placed on a person to continuously monitor health information is a promising new application. At the same time, new low-power wireless standards such as Bluetooth and Zigbee have been proposed for short range, low data-rate communication matching the requirements of these bio-medical applications. However, there are currently few measurements or models describing propagation around the body. To address this problem, electromagnetic waves near the torso are measured and a statistical model is derived for communication in the 915 MHz and 2.45 GHz industrial, scientific and medical bands associated with Zigbee and Bluetooth. Measurement setup and statistical analysis are described.     

Pesticide monitoring programme of the Ministry of Health of Brazil

The structure of the recently introduced Brazilian government programme for monitoring pesticide residues in six major agricultural products is described. Residues found from the analysis of samples of tomatoes and strawberries are discussed in detail. The much greater frequency of detection of pesticide residues, many of which are not approved for use in Brazil, in produce being sold on the domestic market, as opposed to that produced for export, is of major concern. It is perceived that this new monitoring programme will become permanent and be used to underpin enforcement actions that will need to be taken to reduce the numbers of incidents of illegal residues occurring, particularly in fresh fruits and vegetables.     

Surface barrier diode based on zinc selenide with a passivating zinc oxide film

We propose a method of fabricating surface barrier diodes with overlapped metal junction, which provides for a significant decrease in the reverse currents and an increase in the breakdown voltage.     

Influence of the shape of fiber cross section on fabric surface characteristics

Fiber cross sections for use in textiles and composites are becoming more and more complex. Shape impacts fiber or filaments properties and therefore the yarn and fabric characteristics. This paper presents the influence of the fiber cross section on the fabric surface characteristics. The material used was polyester staple fibers, of four different shapes: round, scalloped oval, cruciform and hexachannel. All fibers had the same cut length with different fineness. Yarns obtained from these fibers had nominally the same yarn count, torsion value and structure. Plain jersey fabrics were knitted from each of the yarns under identical conditions and then relaxed prior to testing. Friction behavior was evaluated and a roughness-friction criterion developed. An indirect measurement of the real area of contact was obtained in order to provide roughness and friction properties. The influence of fiber cross section on yarn bending rigidity and on the state of the knitted fabric surface was characterized.