The effects of plasma etching induced gate oxide degradation onMOSFET's 1/f noise

The effects of the plasma etching process induced gate oxide damages on device's low frequency noise behavior are investigated on MOSFET's fabricated with different field plate perimeter to gate area ratio antennas. Abnormal 1/f noise spectrum with a shoulder centered in the frequency range of 100 and to 1 kHz was frequently observed in small geometry devices, and it is attributable to a nonuniform distribution of oxide traps induced by plasma etching process     

层状催化剂颗粒的优化设计——双组分等温平行反应体系

针对双组分等温平行反应体系,分析讨论了以提高催化剂活性和选择性为目标时催化剂活性组分的最优分布形式(为δ-函数分布),并给出了确定这种反应体系的催化剂的最佳活性层位置的计算方法。结果表明:以提高选择性为目标的最佳活性层位置比以提高活性为目标的要更靠近催化剂核心,实用的最优位置应介于二者之间。最后,本文还研究了反应动力学级数、本性选择性以及内扩散模数(Thiele 模数)等因素对最佳活性层位置的影响。     

Orientation in uniaxially stretched plasticized atactic polystyrene

Summary Fourier transform infrared spectroscopy and birefringence measurements have been used to study the changes in molecular orientation which occur on drawing of plasticized as compared to pure polystyrene (PS) at a temperature T=Tg+Cte. No influence of plasticizers on orientation can be detected whatever the interactions between small molecules and PS chains are. Comparison with previous results obtained on PS-poly(vinylmethyl ether) compatible blends confirms the importance of the macromolecular nature of the second component to enhance the friction coefficient leading to higher level of chain orientation.     

用于重离子核反应实验测量的纵向电场气体电离室

本文报道了一种新型的大动态范围，多叠层探测器系统组件之一的纵向电场气体电离室的构造，性能和在中能得离子核反应实验中的应用。     

~（60）Co辐照对聚四氟乙烯表面润湿性的影响

研究了具有低表面能的氟聚合物聚四氟乙烯（ＰＴＦＥ），经６０Ｃｏγ射线辐照后表面状态的变化，以及其对液体介质蒸馏水的润湿性。较详细地论述了辐照后表面粗糙度、结晶度以及表面化学基因等不同因素对ＰＴＦＥ表面润湿性的影响。通过对ＰＴＦＥ及其表面的红外、Ｘ光衍射，表面粗糙度的分析，弄清了辐照后ＰＴＦＥ表面化学基团的改变对有机氟聚合物表加的润湿性影响很大，而粗糙度和结晶度的变化对润湿性影响较小。     

Comparisons of PWM and one-cycle control for power amplifier with multilevel converter

Based on the concepts of cascade multilevel converters and one-cycle technique, comparisons are conducted to characterize the distortion of the pulsewidth modulation (PWM) and one-cycle control methods that were applied to converters. Simulation results for the different control schemes are obtained in PSIM software initially to see the effect of one-cycle control different from that of PWM control. Through the comparisons, the advantages and disadvantages are identified for each method. The one-cycle scheme is better than PWM control in reducing undesirable harmonics and tracing dynamic waveforms. Simulation and experimental results are also provided to verify the conclusions.