二元复合驱采出液矿场处理试验

利用研制的二元复合驱采出液矿场处理装置，对辽河油田兴28块兴191井采出液进行了矿场处理试验。结果表明，采用适宜的破乳剂及处理工艺技术，可以使矿场采出液处理达到净化油含水≤0．5％的指标。     

The maximum bit rates of soliton communication systems with lumpedamplifiers and filters in different distances

The maximum bit rate of a soliton communication system with lumped amplifiers and optical filters is considered. When the dispersion of the fiber varies from one amplifier spacing to another amplifier spacing, the maximum bit rate is significantly reduced. To overcome the effect, the amplitude of the soliton is amplified so that it is still the average soliton corresponding to the fiber dispersion for an amplifier spacing. Thus, the maximum bit rate is only slightly less than that without the dispersion variations. For a given distance, the maximum bit rate limited by the stability and soliton interaction is obtained. The result is compared with that limited by the Gordon-Haus effect. For shorter transmission distance, the maximum bit rate is limited by the stability and soliton interaction. For longer transmission distance, the maximum bit rate is limited by the Gordon-Haus effect     

柴油机低频排气噪声规律分析

针对柴油机（4－85）低频排气噪声，对其产生机理、规律及其影响因素等作了理论计算、分析及实验。对低频排气噪声信号进行频域分析后可知，其主要由一系列离散的谐波组成，是以柴油机点火频率为基频的一种类周期性噪声，有可能应用有源噪声控制技术。     

LaCrMnNiO系热敏陶瓷的微观结构控制

通过对不同配方、工艺下的ＬａＣｒＭｎＮｉＯ系热敏陶瓷的微观结构研究，指出材料的相组成对其宏观电性能的影响，并提出了通过复合工艺利用“过渡相”的形成，对材料的“最终相”加以控制的方法。文中列出了使用ＸＲＤ及ＸＰＳ手段对材料微观结构的分析结果及有关电性能的测试数据。     

Separating inviscid flows

Summary The separating flow of an inviscid fluid is not only a limit solution of the steady separating, laminar fluid flow at high values of the Reynolds number but it is also part of its structure (Smith [1], [2]). This work aims at reexamining the separating flow of inviscid fluid past a bluff body which is fixed in an otherwise uniform stream of fluid. For the purpose of this paper we will assume that the bluff body is a circular cylinder but the theory is applicable to bodies of any shape. It is further assumed that the fluid is in steady two-dimensional motion and is inviscid and of constant density. The flow structure is assumed to consist of a separated flow region, caviting flows in which there exists a free surface on which the pressure is constant, and a wake. A twin spiral vortex model is used in order to determine the shape of the free streamline. Based on the free streamline theory the problem reduces to solving a mixed boundary value problem and a Hilbert solution for the inverse problem in the auxiliary plane is obtained. When we consider the flow in the physical plane the problem is transformed into a direct problem in which the geometry of the solid body is given in advance. We assume that the separation is smooth and thus the curvature of the free streamline at the point of free detachment be equal to that of the body surface. A numerical method for solving the two-dimensional potential flows past arbitrarily shaped curved bluff bodies is developed.When the cavitation number is zero the angle of separation is approximately 55° and the computed results predict that the position of the separation point will move backward as the cavition number increases. The relationships between the drag coefficient, and the width and length of the cavity is determined and is found to be in very good agreement with the predictions of Smith [1].     

Displacement Discontinuity Method for Fracture Mechanics Analysis of Reissner Plates: Static and Dynamic

This paper is concerned with the displacement discontinuity method applied to the shear deformable plates (Reissner’s and Mindlin’s theories) with cracks subjected to static and dynamic loads. Fundamental solutions of dislocation are derived using the Fourier transform method and the Laplace transformation technique. Boundary integral equations are presented in terms of rotations/displacement on the crack surfaces. The Chebyshev polynomials of the second kind are used to evaluate the integral equations with hypersingular kernels on the crack boundaries and determine the stress intensity factors at the crack tips. Comparisons are made with other numerical solutions to demonstrate the proposed method is accurate both for static and dynamic problems.     

中频反应溅射SiO2膜与直流溅射ITO膜的在线联镀

多数ITO透明导电玻璃生产线在实现SiO2膜与ITO膜在线联镀时，应用SiO2靶射频溅射沉积SiO2膜工艺和ITO靶直流溅射沉积ITO膜工艺，如果SiO2膜应用硅靶反应磁控溅射工艺，存在这种工艺是否可以与ITO靶直流溅射沉积ITO膜工艺在线联用以及如何实现联用的问题。作者对现有的生产线进行了改造设计、加工，做了大量实验、质谱分析和多项测试研究，成功地实现反应溅射SiO2膜与ITO膜在线联镀，做到SiO2镀膜室的工作状态的变化基本上不影响ITO镀膜室的工艺条件。     

关于最远点判定及直径的唯一性

给出了点到有界集最远点的一些必要或充分条件，然后对直径的唯一性也给出了一些判定条件。     

纳米超晶格热电材料的研究进展

随着热电材料制备技术和性能研究的发展，纳米超晶格热电薄膜已受到人们的关注，简要介绍了有关纳米超晶格热电材料的结构、热电机理及制作技术，并指出了存在的问题和可能的发展方向。