This work proposed a new path to synthesize Ni-phyllosilicate through the reaction of nickel hydroxide and silica sol on the surface of Ni-foam to form the monolithic Ni-phyllosilicate/Ni-foam catalyst. Ni-phyllosilicate could reprint the morphology of nickel hydroxid and firmly anchor on the framework of Ni-foam, which obtained fine Ni particles of 2.8 nm after reduction in H2 at 650 °C, resulting in high catalytic activity for CO2 methanation. In addition, the Ni-phyllosilicate/Ni-foam catalyst showed high long-term stability in a 100 h-lifetime test owing to the combined effects of surface confinement of Ni-phyllosilicate, firm anchoring between Ni-phyllosilicate and Ni-foam, as well as the high heat transfer property of Ni-foam.
Scientometrics - Due to the development of academic, more and more attentions are paid to citation recommendation. To solve the citation recommendation problem, researchers begin to focus on the... 相似文献
International Journal of Computer Vision - Expressive representations for characterizing face appearances are essential for accurate face detection. Due to different poses, scales, illumination,... 相似文献
Bismuth doped La2-xBixNiO4+δ (x = 0, 0.02 and 0.04) oxides are investigated as SOFC cathodes. The effects of Bi doping on the phase structure, thermal expansion, electrical conduction behavior as well as electrochemical performance are studied. All the samples exist as a tetragonal Ruddlesden-Popper structure. Bi-doped LBNO-0.02 and LBNO-0.04 have good chemical and thermal compatibility with LSGM electrolyte. The average TEC over 20–900°С was 13.4 × 10?6 and 14.2 × 10?6 K?1 for LBNO-0.02 and LBNO-0.04, respectively. The electrical conductivity was decreasing with the rise of Bi doping content. EIS measurement indicates Bi doping can decrease the ASR values. At 750 °C, the obtained ASR for LBNO-0.04 is 0.18 Ωcm2, which is 56% lower than that of the sample without Bi doping, suggesting Bi doping is beneficial to the electrochemical catalytic activity of LBNO cathodes. 相似文献
Cancer remains an intractable medical problem. Rapid diagnosis and identification of cancer are critical to differentiate it from nonmalignant diseases. High-throughput biofluid metabolic analysis has potential for cancer diagnosis. Nevertheless, the present metabolite analysis method does not meet the demand for high-throughput screening of diseases. Herein, a high-throughput, cost-effective, and noninvasive urine metabolic profiling method based on TiO2/MXene-assisted laser desorption/ionization mass spectrometry (LDI-MS) is presented for the efficient screening of bladder cancer (BC) and nonmalignant urinary disease. Combined with machine learning, TiO2/MXene-assisted LDI-MS enables high diagnostic accuracy (96.8%) for the classification of patient groups (including 47 BC and 46 ureteral calculus (UC) patients) from healthy controls (113 cases). In addition, BC patients can also be identified from noncancerous UC individuals with an accuracy of 88.3% in the independent test cohort. Furthermore, metabolite variations between BC and UC individuals are investigated based on relative quantification, and related pathways are also discussed. These results suggest that this method, based on urine metabolic patterns, provides a potential tool for rapidly distinguishing urinary diseases and it may pave the way for precision medicine. 相似文献
The effects of La2O3–Al2O3–SiO2 addition on the thermal conductivity, coefficient of thermal expansion (CTE), Young's modulus and cyclic thermal shock resistance of hot-pressed h-BN composite ceramics were investigated. The samples were heated to 1000 °C and then quenched to room temperature with 1–50 cycles, and the residual flexural strength was used to evaluate cyclic thermal shock resistance. h-BN composite ceramics containing 10 vol% La2O3–Al2O3 and 20 vol% SiO2 addition exhibited the highest flexural strength, thermal conductivity and relatively low CTE, which were beneficial to the excellent thermal shock resistance. In addition, the viscous amorphous phase of ternary La2O3–Al2O3–SiO2 system could accommodate and relax thermal stress contributing to the high thermal shock resistance. Therefore, the residual flexural strength still maintained the value of 234.3 MPa (86.9% of initial strength) after 50 cycles of thermal shock. 相似文献
A series of direct Z-scheme FeIn2S4/Bi2WO6 hierarchical heterostructures with intimate interface contacts were synthesized by in-situ growth route and characterized by systematical analyses. All as-prepared FeIn2S4/Bi2WO6 nanocomposites showed significantly enhanced photocatalytic activity towards photodegradation for the removal of tetracycline hydrochloride (TCH) in comparison with individual FeIn2S4 and Bi2WO6. Meanwhile, the highest photocatalytic degradation activity can be achieved by modulating adding amount of FeIn2S4 in FeIn2S4/Bi2WO6 nanocomposites and the optimized component ratio of FeIn2S4 to Bi2WO6 is determined to be 10 wt%. The enhanced photocatalytic activity could be ascribed to efficient separation between photogenerated holes and electrons based on the construction of direct Z-scheme system. The high photocatalytic stability of resultant 10 wt% FeIn2S4/Bi2WO6 nanocomposites was revealed through six successive recycling reactions. The main intermediate generated during TCH photodegradation was explored by HPLC-MS. Besides, the direct Z-scheme photocatalytic mechanism was confirmed by band position analysis, electron spin resonance (ESR) and active species capture experiment. 相似文献
0.5 at.% Cr:ZnGa2O4 precursor was synthesized by the co-precipitation method with nitrates as raw materials, using ammonium carbonate as the precipitant. Low-agglomerated Cr:ZnGa2O4 powders with an average particle size of 43 nm were obtained by calcining the precursor at 900℃ for 4 h. Using the powders as starting materials, 0.5 at.% Cr:ZnGa2O4 ceramics with an average grain size of about 515 nm were prepared by presintering at 1150℃ for 5 h in air and HIP post-treatment at 1100℃ for 3 h under 200 MPa Ar. The in-line transmittance of 0.5 at.% Cr:ZnGa2O4 ceramics with a thickness of 1.3 mm reaches 59.5% at the wavelength of 700 nm. The Cr:ZnGa2O4 ceramics can be effectively excited by visible light and produce persistent luminescence at 700 nm. For Cr:ZnGa2O4 transparent ceramics, the brightness of afterglow was larger than 0.32 mcd/m2 after 30 min, which is far superior to that of Cr:ZnGa2O4 persistent luminescence powders. 相似文献
Ti3C2Tx (MXene), a new kind of 2D ceramic nanosheets, is receiving more and more attention in the fields of medicine, biology, energy, electronics, etc. However, the preparation and application of MXene in hydrogel is still in its infancy period. Here, we review the latest progress (after 2018) related to MXene hydrogels in time. Aiming at the key issue of the dispersion stability of MXene in hydrogel systems, the preparation strategy, mechanism, advantages and disadvantages of MXene hydrogels are sorted out in detail, and the potential application prospects of MXene composite hydrogel are introduced. Finally, future viewpoints are put forward for the dispersion stability challenges that need solving in the design of MXene hydrogel. 相似文献