Cycling hardening and serration yielding of Fe-Ni-Cr alloy at high temperature under out-phase TMF

Behaviour of hardening and serration yield of a Fe-Ni-Cr alloy under isothermal cycling (ISC) and out-phase TMF was studied on the basis of varied hysteresis loops. Cycling hardening and serrated yielding for ISC depend on the temperature and the total strain range, stronger hardening with serrated yielding at higher strain range under ISC at 600 °C, but no hardening and serrated yielding occurred under ISC at 800 °C. Stronger hardening with stress serration occurred at the thermal path going to the lowest temperature, no stress serration occurred at the highest temperature under the out-phase. The hardening also depends on the total strain range, higher total strain range with lower cycling temperature resulted in a stronger hardening and remarkable serration yielding behavior. Weaker hardening without serrated yielding occurred at near 800 °C may due to an obvious cycling stress drop under out-phase TMF. Change in the shape of the hysteresis loops also expresses the degree of the damage of the tested alloy under out-phase and ISC.     

Fabrication and characterization of nano silver powder prepared by spray pyrolysis

Silver powder was fabricated by spray pyrolysis, using 2%–20% AgNO₃ solution, 336–500 mL/h flux of AgNO₃ solution, 0.28–0.32 MPa flux of carrier gas and in the 620–820 °C temperature range. The effects of furnace set temperature, concentration of AgNO₃ aqueous solution, flux of AgNO₃ aqueous solution as well as carrier gas on the morphology and particle size distribution of silver powder, were investigated. The experimental results showed that with the high concentration of AgNO₃ aqueous solution, the average grain size of silver decreased with the increasing of furnace set temperature. But the gain size distribution was not homogenous, the discontinuous grain growth occurred. With the low concentration of AgNO₃ aqueous solution, the higher furnace set temperature made the nano sliver grains sintered together to grow. Nano silver powder about 100 nm was fabricated by spray pyrolysis, using 2wt% AgNO₃ solutions, 336 mL/h flux of AgNO₃ aqueous solution, 0.32 MPa flux of carrier gas at 720 °C furnace set temperature.     

Possible origins for paramagnetic-ferromagnetic and insulator-metal transitions as well as colossal magnetoresistance in manganites

Systematical investigations of zero-field resistivity, magnetoresistance and magnetization were performed for a typical manganese compound La_2/3Ca_1/3MnO₃. It is argued that the common origin for insulator-metal and paramagenetic ferromagnetic-transitions as well as colossal magnetoresistance is due to the formation of ferromagnetic clusters in the paramagnetic background. The transition to metallic state is resulted from percolation of ferromagnetic metallic clusters, while the colossal magnetoresistance is due to the application of magnetic field, which accelerates the growth of ferromagnetic metallic clusters and causes the shift of the onset temperature for the metallic percolation to higher temperature. Based on the random resistor network model, the zero-field resistivity versus temperature dependence is simulated by using experimental parameters, and experimental data well agree with those in whole temperature range, giving a strong support to our approach.     

Orientation of Bi<Subscript>3.2</Subscript>La<Subscript>0.8</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> ferroelectric thin films with different annealing schedules

Fatigue-free Bi_3.2La_0.8Ti₃O₁₂ ferroelectric thin films were successfully prepared on p-Si (100) substrates using metalorganic solution deposition process. The orientation and formation of 5-layers thin films were studied under different processing conditions using XRD. Experimental results indicate that increase in annealing time at 700 °C after preannealing for 10 min at 400 °C can remarkably increase (200)-orientation of the films derived from the precursor solutions with two contents of citric acid. Meanwhile, high content of citric acid increases the film thickness and is conducive to the a-orientation of the films with the preannealing, and low concentration of the solution is conducive to the c-orientation of the films without the preannealing.     

Synthesis and characterization of polyamides based on dimer acid

A series of dimer acid-based polyamides were synthesized by melt-polycondensation of dimer acid and various aromatic diamines, and were characterized by Fourier transform infrared spectrum (FT-IR) and nuclear magnetic resonance (¹H NMR). The physical properties of the polyamides, such as glass transition temperature, melting temperature, decomposition temperature and mechanical properties were also investigated. The polyamides’ intrinsic viscosity ranges from 1.8 dL·g⁻¹ to 2.2 dL·g⁻¹, and the melting temperature ranges from 140 °C to 181 °C. The glass transition temperatures, observed from dynamic mechanical analysis, fall in the range of 34.8–48.2 °C. The physical and mechanical properties of the resultant polyamides are similar to those of the PA1212. The heat resistance and mechanical properties of poly (4, 4′-diphenylsulfone dimeramide) (PSD) and poly(4, 4′-diphenyl dimeramide) (PPDI) are comparable to those of PA1212.     

Fabrication and mechanical properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiAl composites

Al₂O₃/TiAl composites were successfully fabricated by hot-press-assisted exothermic dispersion method with elemental powder mixtures of Ti, Al TiO₂ and Nb₂O₅, and the microstructure and mechanical properties were investigated. The results indicate the fine Al₂O₃ particles tend to disperse on the grain boundaries. The grain size of TiAl matrix decreases and the hardness increases with increasing Nb₂O₅ content. The bending strength and fracture toughness reach to a maximum when Nb₂O₅ content is 6 wt%, under 642 MPa and 6.69 MPa·m^1/2, respectively. Based on the fractography and the observation of crack propagation path, it is concluded that the strengthening and toughening of such composites at room temperature can be attributed to the refinement of the TiAl matrix, the deflection behavior in the crack propagation and the dispersion of Al₂O₃ particles.     

Influence of Fe/Ni/Al additive on the sintering behaviors of TiB<Subscript>2</Subscript> cermets

Fe-Ni-Al mixtures as hot-pressing sintering additive to Titanium diboride (TiB₂) were studied. It is found that liquid alloy formed under high temperature hardly has effects on the densification behaviors of TiB₂-independent. Fe-Ni-Al additive just works as filler between TiB₂ particles and does not change the TiB₂-independent sintering behaviors. Pressing mode has a great effect on the liquid flowing between TiB₂ particles. Multiple-steps pressing mode will give more time and space for the liquid flowing and improve the relative density of TiB₂-Fe-Ni-Al cermet.     

通用突变控制方法及其在潜艇中的应用

运用非线性动力学和突变理论,研究了高维系统建立具有理想特性突变的控制方法.引入冲失滤波器保证系统平衡点不变,并利用隐式判据、中心流形定理以及规范形法确定控制增益.以潜艇空间运动为例,阐述计算的全过程.该控制方法简便、快捷,可广泛应用到实际控制系统的设计中.     

基于广义AIC和RPC的OFDM航空信道估计算法

文章通过对航空信道的分析,指出其稀疏信道特征,使用普通算法对此信道进行信道估计会引入高阶矩阵运算,为加快收敛速度、降低实现难度,文中提出了一种利用GAIC(generalized Akaike information criterion)准则和RPC(repeated phase-rotated Chu)训练序列的OFDM航空信道LS(1east squares)估计方法,该方法利用GAIC准则确定信道模型的阶次及抽头位置,为减小信道估计的运算复杂度,引入RPC序列作为训练序列,既满足了LS(least squares)估计,又大大简化了计算复杂度.文章针对具体应用给出文中算法的性能仿真结果,证明了此算法可避免高阶矩阵运算,节约了大量权值可忽略抽头所引入的资源占用和计算量,且显著减小估计误差,可更好跟踪快变的稀疏信道.     

Temperature distribution and dynamic control of secondary cooling in slab continuous casting

To predict and optimize the temperature distribution of slab continuous casting in steady operational state, a three-dimensional model (named offline model) based on the heat transfer and solidification theories was developed. Both heat transfer and flux distribution characteristics of the nozzle sprays on the slab were considered, and the complicated boundary condi-tions, such as spray cooling, natural convection, thermal radiation as well as contact cooling of individual rolls were involved in the model. ...