氯和氯胺冲击消毒对二次供水管道生物膜的控制作用

针对建筑二次供水管壁生物膜对饮用水的生物安全性构成的潜在威胁,采用生物膜反应器(BAR)模拟二次供水管道,研究氯和氯胺冲击消毒过程对管壁生物膜的细菌总数、大肠杆菌和异养菌(HPC)灭活效果以及对生物膜结构的影响.结果表明,在第80天时生物膜中生物量达到最大,生物膜宏基因组分析表明,厚壁菌门(Firmicutes)、变形菌门(Proteobacteria)和拟杆菌(Bacteroidetes)为优势菌种.冲击消毒对生物膜的灭活效能与氯和氯胺的质量浓度以及CT值有关,在相同CT值条件下,高质量浓度氯和氯胺的灭活效果更佳.氯和氯胺的生物膜灭活效果对比可以看出,在低投量条件下,氯的细菌总数和大肠杆菌灭活效果好于氯胺,但氯的HPC灭活效果弱于氯胺;在高投量条件下,消毒剂质量浓度和CT值与生物膜的灭活效果无明显相关性,可以达到快速消毒的效果.在氯和氯胺的投加质量浓度为3.0 mg/L、CT值300~400 mg·min/L的最佳冲击消毒条件下,生物膜中细菌总数、大肠杆菌和HPC的灭活率均达到95%以上.从生物膜的表面特性分析可以看出,冲击消毒后生物膜结构破坏明显,生物膜变薄或脱落;氯冲击消毒对生物膜的破坏和削减程度优于氯胺,更有利于管道生物膜的控制.     

Effect of deposition time on microstructures and growth behavior of ZrC coatings prepared by low pressure chemical vapor deposition with the Br<Subscript>2</Subscript>-Zr-C<Subscript>3</Subscript>H<Subscript>6</Subscript>-H<Subscript>2</Subscript>-Ar System

ZrC coatings were deposited on graphite substrates by low pressure chemical vapor deposition (LPCVD) with the Br₂-Zr-C₃H₆-H₂-Ar system. The effects of deposition time on the microstructures and growth behavior of ZrC coatings were investigated. ZrC coating grew in an island-layer mode. The formation of coating was dominated by the nucleation of ZrC in the initial 20 minutes, and the rapid nucleation generated a fine-grained structure of ZrC coating. When the deposition time was over 30 min, the growth of coating was dominated by that of crystals, giving a column-arranged structure. Energy dispersive X-ray spectroscopy showed that the molar ratio of carbon to zirconium was near 1:1 in ZrC coating, and X-ray photoelectron spectroscopy showed that ZrC was the main phase in coatings, accompanied by about 2.5mol% ZrO₂ minor phase.     

Synthesis and characterization of triangular-pyramidal bismuth oxide via a one-step chemical precipitation route

Triangular-pyramidal ω-Bi_2O_3 is successfully synthesized via a one-step wet-chemical method.XRD,SEM,and UV-vis have been employed to characterize the as-prepared samples.Structural characterization by XRD confirms the formation of triclinic ω-Bi_2O_3 with high purity.The well-defined flowerlike Bi_2O_3 structures consisted of many triangular-pyramids are formed.Preparative parameters,such as concentration of PEG 6000,have great effects on the morphology and the particle size.The obvious absorption edge for ω-Bi_2O_3 powder is located at about 493 nm,which corresponds to the optical band gap energy of2.73 eV.     

冲角对车轮与道岔尖轨弹塑性接触的影响

在机车运行中轮轨间存在冲角,改变轮轨接触关系.针对冲角对车轮与尖轨接触的影响问题,建立了车轮—尖轨接触三维有限元模型,通过弹塑性接触计算,分析不同冲角工况下的接触情况.结果表明:轮轨间冲角的存在,导致车轮与钢轨接触位置发生改变,基本轨和尖轨接触斑中心不在同一钢轨横断面上,冲角越大,超前或滞后的数值越大;车轮与尖轨接触法向力随冲角的增大而增大;不同冲角工况下车轮与尖轨的接触等效应力变化规律基本一致,最大等效应力均出现在2 m位置处;冲角的增大会造成尖轨前端等效应力增大,导致车轮轮缘与尖轨的磨耗增加,降低车轮和尖轨的使用寿命.     

Sealing of Ejection Hole at the Bottom of Projectile for Wired Transmission System of Penetration Data

It is difficult to find the projectile when people want to get the penetration data in a hard recovery method, so a recovery system of penetration data is designed based on an ejection mode from the projectile base and a method of wired transmission, at the same time, the system was sealed with a designed sealing device, the working principle of which was introduced. Using Fluent as the simulation platform, the transient pressure of seal cavity was simulated based on the change of chamber pressure, and steady-state pressure of seal clearance and seal cavity were simulated based on the maximum chamber pressure. The sealing performance was tested by a pressure test system. The results of simulation and experiment show that the maximum pressure of seal cavity is 139.4.kPa when the maximum chamber pressure is 242.9.MPa and the maximum temperature of gunpowder explosive gas is 2.166.5.K, so the sealing performance can be assured. The sealing device can be taken as a reference in sealing research on gunpowder gas at the bottom of projection.     

混凝法去除水中TiO2纳米颗粒

为了探讨混凝法去除水中纳米颗粒的可行性及最佳条件,研究了无机混凝剂（PAC、PFS、PAFC）和有机絮凝剂（CPAM、APAM、NPAM）对TiO₂纳米颗粒的去除效果,并考察了投加量、pH、沉淀时间、水力条件及有机无机复配对TiO₂纳米颗粒去除效率的影响。单独投加PAC、PFS和PAFC时,三者对应的最高去除率分别为92.51%、84.43%、95.66%。单独投加CPAM、APAM、NPAM时三者对应的去除率仅为61.72%、29.06%、55.37%。复配最佳混凝条件为：投加40 mg/LPAC和3 mg/LCPAM,pH值为9,G值143.5/s,沉淀时间15 min,此时,TiO₂纳米颗粒去除率为99.6%。     

地面高精度磁测在新疆青河县贝勒克勒铁矿的应用

通过对新疆青河县贝勒克勒铁矿高精度磁法勘探资料的分析和研究,工作区可划分为西部、北部高磁异常区、中西部负值异常区、中部面积正负磁场平缓变化区、东部跳跃变化正值磁异常区,结合工作区岩矿石标本磁性参数可判别各类磁场类型形成的地质原因。划分局部磁异常6个,其中M1、M2、M3磁异常与地下隐伏含磁铁矿石英岩有关,M4、M5、M6磁异常与含铁石英岩有关。对局部典型异常M1、M4进行了半定量解释,并进行了钻探验证,实际验证结果与推断结果较为吻合。     

脱硝系统改造后炉膛负压波动原因分析及对策

选择性催化还原法(SCR)是目前燃煤电厂普遍采用的烟气脱硝技术,锅炉加装SCR脱硝装置后易出现空预器堵塞、炉膛负压异常波动等问题。以某燃煤机组为例,对空气预热器进出口压差、炉膛负压、入炉煤质、机组运行工况等进行综合分析,发现炉膛负压异常是由于锅炉进行SCR烟气脱硝时空气预热器发生局部堵塞,其根本原因为SCR装置过量喷氨或局部过量喷氨造成大量氨逃逸所致。并在分析原因的基础上提出治理对策。     

地震反演地震地质储层参数转换应用——以歧口地区为例

针对同一研究区不同研究目标,对地震反演方法进行优化组合后,得到相应的波阻抗反演体,再进行储层参数转换。测井曲线重构波阻抗反演及多门槛制法砂体厚度预测相结合,有效提高了歧口地区深层砂体厚度预测的准确性。根据原始波阻抗反演结果,结合Fillippone法计算地层压力系数理论,提出断陷盆地不同埋深地层压实差异影响因素下地层压力系数计算方法,通过歧口地区异常压力预测可能的深层天然气富集区,预测与实际钻井结果相符。     

Multi-objective robust design optimization of a novel negative Poisson’s ratio bumper system

Negative Poisson’s ratio (NPR) structure has outstanding performances in lightweight and energy absorption, and it can be widely applied in automotive industries. By combining the front anti-collision beam, crash box and NPR structure, a novel NPR bumper system for improving the crashworthiness is first proposed in the work. The performances of the NPR bumper system are detailed studied by comparing to traditional bumper system and aluminum foam filled bumper system. To achieve the rapid design while considering perturbation induced by parameter uncertainties, a multi-objective robust design optimization method of the NPR bumper system is also proposed. The parametric model of the bumper system is constructed by combining the full parametric model of the traditional bumper system and the parametric model of the NPR structure. Optimal Latin hypercube sampling technique and dual response surface method are combined to construct the surrogate models. The multi-objective robust optimization results of the NPR bumper system are then obtained by applying the multi-objective particle swarm optimization algorithm and six sigma criteria. The results yielded from the optimizations indicate that the energy absorption capacity is improved significantly by the NPR bumper system and its performances are further optimized efficiently by the multi-objective robust design optimization method.