Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

Development of a safety critical software requirements verification method with combined CPN and PVS: a nuclear power plant protection system application

Safety-critical software systems such as certain nuclear instrumentation and control (NI&C) systems should be developed with thorough verification. This study presents a method of software requirement verification with a case study for a nuclear power plant (NPP) protection system. The verification introduces colored petri net (CPN) for system modeling and prototype verification system (PVS) for mathematical verification. In order to aid flow-through from modeling by CPN to mathematical proof by PVS, an information extractor from CPN models has been developed in this paper. In order to convert the extracted information to the PVS specification language, a translator has also been developed. This combined method has been applied to the functional requirements of the Wolsong NPP Shut Down System #2 (SDS2); logical properties of the requirements were verified. Through this research, guidelines and a tool support for the use of formal methods have been developed for application to NI&C software verification.     

Development of core mode blocker with H/sub 2/-loaded Ge-B codoped fibres

A novel fabrication method of the core mode blocker by exposing H/sub 2/-loaded Ge-B codoped fibres to local electric arc discharge for application to the LPFGs-based tunable all-fibre bandpass filter with 6.5 nm bandwidth and 40 nm tuning range is presented.     

油气吸收回收系统的研究及工业应用——(Ⅰ)中型试验及结果分析

在蒸发油气吸收回收技术小试研究的基础上，开发出常温常压吸收法油气回收中试装置，并利用已开发的吸收剂AbsFOV-97进行了中试试验。结果表明，当系统进料气、吸收剂AbsFOV-97、汽油的体积流量比为10．0：1．0：0．5、真空泵解吸压力小于13．3kPa时，系统回收率高达97％以上，高于设计指标，且回收汽油的质量满足使用要求。统计数据表明，油气回收系统进料气、尾气中平均油气摩尔质量分别为65．51、48．97g／mol，该值可为油品蒸发损耗及其控制技术的评价提供参考。     

改性乳化沥青的发展和应用概况

综述了改性乳化沥青的发展及应用概况,重点讨论了改性乳化沥青的生产、制备工艺、稳定性影响因素,并对国内外改性乳化沥青的应用情况加以概述。     

容灾系统中存储方案选择的研究

论文首先阐述了在容灾系统中存储方案的重要性,讨论了存储方案需要考虑的衡量指标,然后介绍了主要的存储方式,根据衡量指标划分了存储方式的特性范围,最后着重研究了容灾系统中存储方案的选择流程,并使用一个实例说明容灾系统中存储方案的选择流程。     

基于单片机加压控制的PCD复合片真空扩散焊接

文章针对普通钎焊的聚晶金刚石钻头剪切强度不高，提出了采用单片机加压控制的PCD复合片真空扩散焊接的设计思想，在对原真空扩散焊机液压改造的基础上给出如何由单片机控制加压的电路和程序流程设计。实际应用表明，该技术经济实用，有较好的经济效益。     

双层有机电致发光器件有机层厚度优化的数值研究

在陷阱电荷限制电流传导理论的基础上,提出了双层有机电致发光器件的数值模型,研究了结构为"阳极/空穴输运层(HTL)/发光层(EML)/阴极"的器件中电流密度和量子效率随有机层的特征陷阱能量、陷阱密度和载流子迁移率的依赖关系. 研究发现,对于给定的HTL和EML的特征陷阱能量、陷阱密度和载流子迁移率,存在一个最优的HTL和EML之间的厚度比率,在此最优厚度比下,器件的电流密度和量子效率达到最大.通过有机层厚度的优化,器件的电流密度和量子效率可提高多达两个数量级.另外,还研究了最优厚度比随有机层特征陷阱能量、总陷阱密度和载流子迁移率之间的定量关系.     

Improving narrow bandgap a-SiGe:H alloys grown by hot-wire chemical vapor deposition

We have improved the electronic properties of narrow-bandgap (Tauc gap below 1.5 eV) amorphous-silicon germanium alloys (a-SiGe:H) grown by hot-wire chemical vapor deposition (HWCVD) by lowering the substrate temperature and deposition rate. Prior to this work, we were unable to grow a-SiGe:H alloys with bandgaps below 1.5 eV that had photo-to-dark conductivity ratios comparable with our plasma-enhanced CVD (PECVD) grown materials [B.P. Nelson et al., Mater. Res. Soc. Symp. 507 (1998) 447]. Decreasing the filament diameter from our standard configuration of 0.5 mm to 0.38 or 0.25 mm provides first big improvements in the photoresponse of these alloys. Lowering the substrate temperature from our previous optimal temperatures (T_sub starting at 435 °C) to at 250 °C provides additional photo-to-dark conductivity ratio increasing by two orders of magnitude for growth conditions containing 20–30% GeH₄ in the gas phase (relative to the total GeH₄+SiH₄ flow).     

用CMOS工艺实现非接触IC卡天线的集成化设计

论述了用CMOS工艺实现非接触式IC卡天线的集成化需要考虑的各个方面,建立了集成天线的模型,给出了合理的设计方案,并通过实验验证了模型和设计方案.实验结果表明,采用片上天线完全可以提供非接触式IC卡工作所需要的能量.在频率为2 2 .5 MHz、感应强度为6×10 - 4 T的磁场中,面积为2 m m×2 mm的集成天线可以为10 kΩ的负载提供1.2 2 5 m W的能量.