Finite element analysis of optimized brace angle for the diagrid structural system

International Journal of Steel Structures - The Diagrid structural system is considered to be the best structural system for constructing free form structures, but it is also a very effective...     

ESMRMB 2017, 34th Annual Scientific Meeting,Barcelona, ES,October 19–October 21: Abstracts,Thursday

Objective

Current magnetic resonance imaging (MRI) axon diameter measurements rely on the pulsed gradient spin-echo sequence, which is unable to provide diffusion times short enough to measure small axon diameters. This study combines the AxCaliber axon diameter fitting method with data generated from Monte Carlo simulations of oscillating gradient spin-echo sequences (OGSE) to infer micron-sized axon diameters, in order to determine the feasibility of using MRI to infer smaller axon diameters in brain tissue.

Materials and methods

Monte Carlo computer simulation data were synthesized from tissue geometries of cylinders of different diameters using a range of gradient frequencies in the cosine OGSE sequence . Data were fitted to the AxCaliber method modified to allow the new pulse sequence. Intra- and extra-axonal water were studied separately and together.

Results

The simulations revealed the extra-axonal model to be problematic. Rather than change the model, we found that restricting the range of gradient frequencies such that the measured apparent diffusion coefficient was constant over that range resulted in more accurate fitted diameters. Thus a careful selection of frequency ranges is needed for the AxCaliber method to correctly model extra-axonal water, or adaptations to the method are needed. This restriction helped reduce the necessary gradient strengths for measurements that could be performed with parameters feasible for a Bruker BG6 gradient set. For these experiments, the simulations inferred diameters as small as 0.5 μm on square-packed and randomly packed cylinders. The accuracy of the inferred diameters was found to be dependent on the signal-to-noise ratio (SNR), with smaller diameters more affected by noise, although all diameter distributions were distinguishable from one another for all SNRs tested.

Conclusion

The results of this study indicate the feasibility of using MRI with OGSE on preclinical scanners to infer small axon diameters.

     

Fitting interrelated datasets: metabolite diffusion and general lineshapes

Objective

Simultaneous modeling of true 2-D spectroscopy data, or more generally, interrelated spectral datasets has been described previously and is useful for quantitative magnetic resonance spectroscopy applications. In this study, a combined method of reference-lineshape enhanced model fitting and two-dimensional prior-knowledge fitting for the case of diffusion weighted MR spectroscopy is presented.

Materials and methods

Time-dependent field distortions determined from a water reference are applied to the spectral bases used in linear-combination modeling of interrelated spectra. This was implemented together with a simultaneous spectral and diffusion model fitting in the previously described Fitting Tool for Arrays of Interrelated Datasets (FiTAID), where prior knowledge conditions and restraints can be enforced in two dimensions.

Results

The benefit in terms of increased accuracy and precision of parameters is illustrated with examples from Monte Carlo simulations, in vitro and in vivo human brain scans for one- and two-dimensional datasets from 2-D separation, inversion recovery and diffusion-weighted spectroscopy (DWS). For DWS, it was found that acquisitions could be substantially shortened.

Conclusion

It is shown that inclusion of a measured lineshape into modeling of interrelated MR spectra is beneficial and can be combined also with simultaneous spectral and diffusion modeling.

     

Sensitive magnetic field sensor using 2D magnetic photonic crystal slab waveguide based on BIG/GGG structure

A kind of magnetic field sensor (MFS) using a two-dimensional (2D) magnetic photonic crystal (MPC) slab waveguide as the sensing structure is proposed and investigated numerically. The slab structure is based on bismuth iron garnet (BIG), a well-known magnetic material with effective magnetooptical (MO) properties, sandwiched with gadolinium gallium garnet (GGG) as substrate. The complete photonic bandgap (PBG) of the 2D MPC is simulated and optimized for realization of polarization-independent waveguides. The simulation results show that the width and position of the complete PBG depend on the thickness of the BIG slab and the radius of the air holes used in the design. By reducing the lightwave propagation losses and enhancing the mode conversion ratio, increased sensitivity is obtained. Based on the Faraday effect, a good linear relationship is observed between the normalized output light intensity and the magnetic field strength as the gyrotropy parameter g is varied from 0.13 to 0.19, a g-range used as the sensor dynamic range. The remarkable enhancement in sensing performance due to the MO effect makes the designed device suitable for magnetic field sensing. The results are discussed to provide a basis for investigation of 2D MPC slab waveguides based on the same structure, which are of particular interest for development of highly sensitive MFSs.     

港口防波堤的损坏及原因分析

随着港口建设规模的不断扩大,深水防波堤建设项目也逐年增多,防波堤在抵御海浪侵袭等方面具有重要的作用。但近年来不断出现的防波堤损坏事件,给港口水工工程建设造成了一定的困扰。本文就港口防波堤的损坏情况及损坏的原因进行了分析。     

基于精益生产的工程机械齿轮工厂设计

分析了基于精益生产的工程机械齿轮工厂设计,从生产组织、总体布局、设备和信息化4个方面提出了适用于工程机械齿轮工厂的精益设计方法,并做了实例分析。     

减缩剂对混凝土干缩开裂的影响及其应用

从试验设备、步骤等，阐述了干缩试验的方法，对试验的原材料和配合比及其常规性能测定结果作了分析，并提出工程中应注意的几点问题，以利采用减缩剂抑制混凝土开裂收到良好效果。     

Design and manufacture of high-filling-efficiency microfluidic devices

In this study, we proposed an efficient method for mass production of high-filling-efficiency microfluidic devices. Precision machining was the main process of device fabrication. The commercially available SolidWorks software was adopted for structure design. Unigraphics software was then used to simulate the machining process. The simulated tooling file was then loaded into a CNC milling machine for mold production. The fabricated metal mold was used for pouring polydimethylsiloxane (PDMS) to obtain high-filling-efficiency microfluidic structures. Finally, plasma-assisted packaging was conducted to tightly bind the PDMS microfluidic structure to the glass substrate. Experimental results showed that the additional semicircular filling structure and expended fill-entry structure can efficiently enhance filling efficiency of the microchannel device. The incubation well array can be completely filled at a relatively short filling time. The proposed highly efficient filling microfluidic device possesses advantages, such as feasibility for mass production and cost effectiveness.