Solution of Helmholtz equation by Trefftz method

The application of the Trefftz method for calculating wave forces on offshore structures is presented. Indirect and direct formulations using complete and non-singular systems of Trefftz functions for the Helmholtz equation are posed in this paper. An effective technique using different interpolation functions for the velocity potential and wave force are suggested to improve the computational accuracy of the wave force. The numerical examples show that the present method is highly efficient and accurate.     

Effects of compressive and tensile stress on the growth mode of epitaxial oxide films

Oxide films were deposited on different substrates by laser molecular beam epitaxy. Reflection high-energy electron diffraction was performed to in situ investigate the change of growth mode and the lattice relaxation during the growth. An asymmetrical phenomenon was found in the two kinds of strain states, compressive stress and tensile stress of heterostructures with different lattice mismatch. In the case of BaTiO₃/SrTiO₃ (2.2%), 2D layer-by-layer growth mode without lattice relaxation can be maintained for a longer period for BTO films on STO with compressive stress, comparing to STO films on BTO with tensile stress. When MgO films were deposited on SrTiO₃ with a large mismatch of 7.8%, compressive stress leads to rapid lattice relaxation with a very thin wet layer, and 3D strained island were observed. As a comparison, SrTiO₃ films on MgO with tensile stress were configured. No RHEED patterns can be observed duo to a large tensile stress.     

Influence of protein and lipid concentration of the test lubricant on the wear of ultra high molecular weight polyethylene

To gain a better understanding of the ultra-high molecular weight polyethylene (UHMWPE) wear mechanism in the physiological environment, the effects of protein and lipid constituents of synovial fluid on the specific wear rate of UHMWPE were examined experimentally. The multidirectional sliding pin-on-plate wear tester was employed to simulate the simplified sliding condition of hip joint prostheses. Bovine serum γ-globulin and synthetic l--DPPC were used as model protein and lipid constituents of synovia, respectively. Results of the wear test indicated that the UHMWPE wear rate primarily depended on the protein concentration of the test lubricant. Lipids acted as a boundary lubricant and reduced polyethylene wear in the low protein lubricants. However, the polyethylene wear rate increased with increasing lipid concentrations if the protein concentration was within the physiological level. Increased interactions between protein and lipid molecules and lipid diffusion to polyethylene surface might be responsible for the increased wear.     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

SHS of shape memory CuZnAl alloys

Aiming at preparation of shape memory alloys (SMAs), we explored the SHS of Cu_{1 − x} Zn_{1 − y} Al_{1 − z} alloys (0.29 < x < 0.30, 0.74 < y < 0.75, and 0.83 < z < 0.96). The most pronounced shape memory effect was exhibited by the alloys of the following compositions (wt %): (1) Cu(70.6)Zn(25.4)Al(4.0), (2) Cu(70.1)Zn(25.9)Al(4.0), and (3) Cu(69.9)Zn(26.1)Al(4.0). The effect of process parameters on the synthesis of CuZnAl alloys was studied by XRD, optical microscopy, and scanning electron microscopy (SEM). The grain size of CuZnAl was found to depend on the relative amount of the primary CuZn and AlZn phases. Changes in the transformation temperature and heat of transformation are discussed in terms of ignition intensity and compaction. Mechanism of the process depends on the level of the temperature attained relative to the melting point of components. At the melting point of AlZn, the process is controlled by the solid-state diffusion of AlZn into a product layer. The ignition temperature for this system depends on the temperature of the austenite-martensite transformation in CuZnAl alloys. The composition and structure of the products was found to markedly depend on process parameters. The SHS technique has been successfully used to prepare a variety of SMAs.      

Integrated carbon nanotube field emission differential amplifier: Modeling and measurement of the common-mode rejection ratio

A novel integrated vacuum field emission (VFE) differential amplifier (diff-amp) utilizing carbon nanotube (CNT) emitters has been developed. A dual-mask microfabrication process was employed to achieve a VFE diff-amp by integrating identical CNT VFE transistors with built-in split gates and integrated anodes. The identical pair of triode amplifiers was well-matched in their device characteristics. The measured ac small-signal characteristics of the diff-amp showed a common-mode-rejection ratio (CMRR) of ~ 320 (~ 50 dB). The proposed analytical model of the CMRR was verified to be in good agreement with the experimental data. The successful implementation of the CNT diff-amp demonstrates a new way to achieve temperature and radiation tolerant VFE integrated microelectronics.     

Effect of vibration condition and inter-particle frictions on the packing of uniform spheres

We present a numerical study of the packing of uniform spheres under three-dimensional vibration using the discrete element method (DEM), focusing on the effects of vibration condition (amplitude and frequency) and inter-particle frictions (sliding and rolling frictions). The results are analysed in terms of packing density, coordination number (CN), radial distribution function (RDF) and pore structure. It is shown that increasing either the vibration amplitude or frequency causes packing density to increase initially to a maximum and then decrease. Both vibration frequency and amplitude should be considered to characterize the effect of vibration process on packing structure. The sliding and rolling frictions between particles can decrease packing density since they dissipate energy, although the effect of rolling friction is less significant. In line with the change of packing density, microstructural properties such as CN, RDF and pore distribution also change: a looser packing often corresponds to smaller CN, less peaked RDF and larger but more widely distributed pores.     

Formation mechanism of 21R AlN-polytypoids in aluminothermic reduction and nitridation process

Synthesis of 21R AlN polytypoids was investigated using Al and ultrafine SiO₂ powder in a flowing nitrogen atmosphere by means of thermal gravity (TG), differential scanning calorimeter (DSC), X-ray diffractometer (XRD) and scanning electronic microscope (SEM) linked with energy dispersive spectrometer (EDS). The results showed that the formation mechanism of AlN polytypoids was different from that in reaction sintering process using Si₃N₄, AlN, Al₂O₃ and other sintering additive as raw materials. It was suggested that firstly Al reduce SiO₂ into Si and is also nitrided into AlN, then AlN, Al₂O₃ and SiO₂ dissolve into silicon liquid until the AlN polytypoids precipitate in saturated liquid in a flowing nitrogen atmosphere at lower than 1700 °C.     

Tunable laser-based design and analysis for fractional lambda switches

Fractional lambda switching (FlambdaS) is a novel approach for traffic management over all-optical networks with sub-wavelength provisioning capability. The unique characteristic of FlambdaS is the utilization of UTC (coordinated universal time) for switching with minimum or no buffers. Several central research issues are still open in FlambdaS and need to be formally defined and analyzed. In this paper, we introduce three novel switch designs that are based on the use of tunable lasers (which can be replaced in the future with wavelength converters). First, the paper presents analytical results of scheduling feasibility, which measures the total number of possible different schedules for each switch design. Then it is shown that the architecture with the highest scheduling feasibility is strictly non blocking in the space domain. Next, the paper provides a closed form analysis of the blocking probability in the time domain, which is applicable for any strictly non-space blocking switch, using combinatorics. In addition, the paper provides measures of the switching hardware complexity, which, for the strictly non-blocking architecture, has the same switching complexity as Clos interconnection network, i.e., O(N'radic(N')) where N' is the number of optical channels.