Influence of protein and lipid concentration of the test lubricant on the wear of ultra high molecular weight polyethylene

To gain a better understanding of the ultra-high molecular weight polyethylene (UHMWPE) wear mechanism in the physiological environment, the effects of protein and lipid constituents of synovial fluid on the specific wear rate of UHMWPE were examined experimentally. The multidirectional sliding pin-on-plate wear tester was employed to simulate the simplified sliding condition of hip joint prostheses. Bovine serum γ-globulin and synthetic l--DPPC were used as model protein and lipid constituents of synovia, respectively. Results of the wear test indicated that the UHMWPE wear rate primarily depended on the protein concentration of the test lubricant. Lipids acted as a boundary lubricant and reduced polyethylene wear in the low protein lubricants. However, the polyethylene wear rate increased with increasing lipid concentrations if the protein concentration was within the physiological level. Increased interactions between protein and lipid molecules and lipid diffusion to polyethylene surface might be responsible for the increased wear.     

Perfect Blind-Channel Shortening for Multicarrier Systems

In multicarrier systems, when the order of a channel impulse response is larger than the length of the cyclic prefix (CP), there is a significant performance degradation due to interblock interference (IBI). This paper proposes a blind-channel shortening method in which the equalizer parameter vector is formed by the noise subspace of the received signal correlation matrix so that the output power is maximized. The proposed method can not only shorten the effective channel impulse response to within the CP length but also maximize the output signal-to-interference-and-noise ratio while eliminating the IBI. We point out that the performance depends on the choice of a decision delay and propose a simple method for determining the appropriate delay. We propose both a batch algorithm and an adaptive algorithm and show by simulation that they are superior to the conventional algorithms.     

An order-specific clustering algorithm for the determination of representative demand curves

Data clustering consists of a group of procedures used to collect similar entries or data points within a set into clusters. No existing clustering technique considers entries sequentially in time. In some cases, it is desirable to generate clusters that represent a segment of a time-ordered data set. For these purposes, an order-specific clustering algorithm is proposed. The proposed algorithm employs representative load curves to describe the clusters it generates. The capabilities of the order-specific clustering algorithm are demonstrated on a case study using electricity demand data for the province of Ontario, Canada. Two different applications of the clustering algorithm on this data set are given to demonstrate the effect of error threshold values on the formation of clusters. An analysis of the error for each of these clustering applications is presented.     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

Sp3/sp2 character of the carbon and hydrogen configuration in micro- and nanocrystalline diamond

Hot filament and microwave plasma CVD micro- nanocrystalline diamond films are analysed by visible and ultra-violet excitation source Raman spectroscopy. The sample grain size varies from 20 nm to 2 μm. The hydrogen concentration in samples is measured by SIMS and compared to the grain size, and to the ratio of sp² carbon bonds determined by Raman spectroscopy from the 1332 cm^− 1 diamond peak and the sp² 1550 cm^− 1 G band. Hydrogen concentration appears to be proportional to the sp² bonds ratio. The 3000 cm^− 1 CH_x stretching mode band intensity observed on the Raman spectra is decreasing with the G band intensity. Thermal annealing modifies the sp² phase structure and concentration, as hydrogen outdiffuses.     

SHS of shape memory CuZnAl alloys

Aiming at preparation of shape memory alloys (SMAs), we explored the SHS of Cu_{1 − x} Zn_{1 − y} Al_{1 − z} alloys (0.29 < x < 0.30, 0.74 < y < 0.75, and 0.83 < z < 0.96). The most pronounced shape memory effect was exhibited by the alloys of the following compositions (wt %): (1) Cu(70.6)Zn(25.4)Al(4.0), (2) Cu(70.1)Zn(25.9)Al(4.0), and (3) Cu(69.9)Zn(26.1)Al(4.0). The effect of process parameters on the synthesis of CuZnAl alloys was studied by XRD, optical microscopy, and scanning electron microscopy (SEM). The grain size of CuZnAl was found to depend on the relative amount of the primary CuZn and AlZn phases. Changes in the transformation temperature and heat of transformation are discussed in terms of ignition intensity and compaction. Mechanism of the process depends on the level of the temperature attained relative to the melting point of components. At the melting point of AlZn, the process is controlled by the solid-state diffusion of AlZn into a product layer. The ignition temperature for this system depends on the temperature of the austenite-martensite transformation in CuZnAl alloys. The composition and structure of the products was found to markedly depend on process parameters. The SHS technique has been successfully used to prepare a variety of SMAs.      

Integrated carbon nanotube field emission differential amplifier: Modeling and measurement of the common-mode rejection ratio

A novel integrated vacuum field emission (VFE) differential amplifier (diff-amp) utilizing carbon nanotube (CNT) emitters has been developed. A dual-mask microfabrication process was employed to achieve a VFE diff-amp by integrating identical CNT VFE transistors with built-in split gates and integrated anodes. The identical pair of triode amplifiers was well-matched in their device characteristics. The measured ac small-signal characteristics of the diff-amp showed a common-mode-rejection ratio (CMRR) of ~ 320 (~ 50 dB). The proposed analytical model of the CMRR was verified to be in good agreement with the experimental data. The successful implementation of the CNT diff-amp demonstrates a new way to achieve temperature and radiation tolerant VFE integrated microelectronics.     

Effect of vibration condition and inter-particle frictions on the packing of uniform spheres

We present a numerical study of the packing of uniform spheres under three-dimensional vibration using the discrete element method (DEM), focusing on the effects of vibration condition (amplitude and frequency) and inter-particle frictions (sliding and rolling frictions). The results are analysed in terms of packing density, coordination number (CN), radial distribution function (RDF) and pore structure. It is shown that increasing either the vibration amplitude or frequency causes packing density to increase initially to a maximum and then decrease. Both vibration frequency and amplitude should be considered to characterize the effect of vibration process on packing structure. The sliding and rolling frictions between particles can decrease packing density since they dissipate energy, although the effect of rolling friction is less significant. In line with the change of packing density, microstructural properties such as CN, RDF and pore distribution also change: a looser packing often corresponds to smaller CN, less peaked RDF and larger but more widely distributed pores.