Synthesis of nanopowders with low agglomeration by elaborating Φ values for producing Gd2O3-MgO nanocomposites with extremely fine grain sizes and high mid-infrared transparency

Refining ceramic microstructures to the nanometric range to minimize light scattering provides an interesting methodology for developing novel optical ceramic materials. In this work, we reported the fabrication and properties of a new nanocomposite optical ceramic of Gd₂O₃-MgO. The citric acid sol-gel combustion method was adopted to fabricate Gd₂O₃-MgO nanocomposites with fine-grain sizes, dense microstructures and homogeneous phase domains. Nanopowders with low agglomeration and improved sinterability can be obtained by elaborating Φ values. Further refining of the microstructure of the nanocomposites was achieved by elaborating the hot-pressing conditions. The sample sintered at 65 MPa and 1300 °C showed a quite high hardness value of 14.3 ± 0.2 GPa, a high transmittance of 80.3 %–84.7 % over the 3?6 μm wavelength range, due mainly to its extremely fine-grain size of Gd₂O₃ and MgO (93 and 78 nm, respectively) and high density.     

变压器内部故障在线检测方法仿真及误差分析

为研究变压器内部故障在线检测方法的有效性及抗干扰性,搭建实际变压器的非线性三维有限元模型.对变压器常见几种类型的内部故障进行详细的结构仿真,通过"场-路耦合法"构建各类型故障的ΔV-I1轨迹.同时,通过对正常绕组的测量信号设置一定的误差,构建了考虑测量误差时的误差轨迹.在此基础上,将正常时的标准轨迹、误差轨迹和各种类型的故障轨迹进行对比分析,通过对ΔV-I1轨迹特征差异的定性分析与定量计算,验证该方法在实际应用中的有效性,总结判断各类型故障的规则,同时针对测量误差所造成的干扰提出了建议.     

基于PBFT区块链技术的电网企业仓储系统

提出了一种基于实用拜占庭容错(PBFT)算法的区块链技术,首先对传统的实用拜占庭容错算法原理进行了阐述,该传统算法包含前期、需求、预准备、准备、确认、答复6个阶段,但传统算法具有实时性差、缺乏惩罚机制、带宽高的缺点。针对出现的这些问题,又对传统算法进行了改进,具体涉及记账节点、共识过程以及视图切换过程。通过测试进一步证明了该改进算法的实用性,并将该算法应用于电网企业中,构建的虚拟仓库实现了联储联备,降低了库存资金的耗费,并且提高了电网企业库存管理的效率。     

三氯乙酸终止液对木瓜蛋白酶酶活测定的影响研究

本实验研究了不同的三氯乙酸终止液,对木瓜蛋白酶酶活的影响。通过使用两种检测方法,不同配方的三氯乙酸终止液进行实验。结果表明,使用两种不同配方的三氯乙酸终止液所得的结果相差2倍多。用不同稀释浓度的三氯乙酸终止液,在高浓度时,不同浓度的三氯乙酸终止液得到的结果差别很大,随着三氯乙酸浓度的降低,所测得的酶活不断升高;但是在低浓度时,不同浓度的三氯乙酸终止液得到的结果差别不大。     

定距螺旋桨对船用主机外特性的要求分析

为解决定距螺旋桨与船用主机在船舶运行工况的机桨匹配问题,结合船舶系泊和航行试验的相关标准,分析和归纳船舶运行数据,将实船测试与船机桨匹配理论计算相结合,得出运输船和拖轮在常用工况及特殊工况下定距螺旋桨对主机外特性的定量要求,为配套不同细分市场时船用主机的优化和开发提供参考依据。     

Characterizations of friction welding joint interface for AISI 316

Because of heat amount is different from peripheral to central of friction welding interface, which is leaded to vary the characterizations along that interface. Current study, respectively, focused on the effect of different friction pressure on micro-structural and mechanical properties of that friction welding joint interface. Presently, these friction pressures are 110, 130, 150 and 170 MPa while kept all other conditions constant. The effects of different friction pressure on welding interface characterization were investigated by EDX, SEM, tensile, compression, impact and hardness tests. The tensile tests carried out on the standardized test piece with diameter 6 mm and 8 mm, thus, compression tests were extracted from the positions of 0°, 45° 90° with test specimen of 4 mm diameter and 6.5 mm length at weld center. Whereas, the impact test pieces were picked up in two positions, the first one is symmetrical, which it obtained to the respect of the rotation axis and the interface, on the other hand, the second one is non-symmetrical with the axis of rotation and symmetrical to the interface, for making the notch head coincide with the center of the welded joint, The obtained results showed that with reducing of friction pressure will present lack of bonding increasing from peripheral toward the welding center, which will responsible on reducing of the mechanical properties such as tensile, compression and impact strength.     

床温及SNCR脱硝对CFB锅炉NOx和N2O排放影响的试验研究

为了研究循环流化床（CFB）锅炉燃用无烟煤时床温及选择性非催化还原（SNCR）脱硝对于NO和N2O排放的影响，在1 MW CFB试验装置上开展了试验研究。结果表明:床温由880 ℃提高到970 ℃，NO排放质量浓度由119.5 mg/m3上升到226.0 mg/m3，N2O排放质量浓度由216.0 mg/m3降低到102.2 mg/m3；在氨氮摩尔比（NSR）为0~3.7之间，随着NSR的提高，脱硝效率从0上升到50.72%；进一步提高NSR到5.2，脱硝效率升至53.61%，增加较为缓慢；随着NSR从0提高到1.7，N2O排放质量浓度由84.3 mg/m3上升至118.3 mg/m3，增长较为缓慢；进一步提高NSR至2.0，N2O排放质量浓度上升至187.7 mg/m3，增长速度提高；继续提高NSR至5.2，N2O排放质量浓度上升至381.4 mg/m3；CFB锅炉采用以尿素为还原剂的SNCR脱硝工艺时，单纯通过加大NSR来提高脱硝效率不仅效果有限，过量喷入的还原剂会造成N2O排放量的显著提高。     

卷取机前夹送辊不同驱动方式的夹送力对比分析

文章针对有色金属加工生产机组中卷取机前夹送辊驱动方式的不同,对夹送辊的结构和驱动力矩做对比分析,同时进行理论设计计算,供设计参考使用。