直接氯化法合成对硝基氯化苄

介绍了以对硝基甲苯和氯气为原料 ,在催化剂存在下合成对硝基氯化苄的方法 ,考察了催化剂种类、反应温度、溶剂配比等因素对反应的影响 ,优化的反应条件为 :对硝基甲苯用量 1 3 7g,对硝基甲苯 /邻二氯苯 (摩尔比 ) =1∶ 0 .6,w (偶氮二异丁腈 ) =0 .6% ,反应时间 3 h,反应温度 1 60℃ ,产物单程收率大于 65 % ;将反应混合物中未反应的原料分离后 ,以无水乙醇为溶剂结晶纯化 ,物料 /溶剂 (摩尔比 ) =1∶ 1 .5时晶体含量在 99.0 %以上 ,结晶收率达 67     

模糊数学识别火山岩岩性

针对火岩地层岩性识别成功率低的状况，应用模糊数学原理，建立模糊数学识别火山岩岩性模式，识别和划分火山岩地层岩性，以便进一步深入研究火山岩油气藏储层，选择8个反映火山岩岩性测井参数，确定阈值；利用所建立的火山岩岩性识别模式，对火山岩岩性进行分类；依据最大隶属原则，识别火山岩岩性，应用实地研究资料，识别10种火山岩岩性，并与岩心鉴定统计分析结果对比，一致性达85％。表明该方法识别火山岩岩性精度较高，在地质上具有很好的应用前景。     

Improvement of RCA transistor using RTA annealing after theformation of interfacial oxide

A polysilicon emitter RCA transistor (an ultra-thin interfacial oxide layer exists between polysilicon and silicon emitter) is presented which can operate at 77 K for the first time. An ultra-thin (1.5 nm) interfacial oxide layer is grown deliberately between polysilicon and silicon emitter using RCA oxidation and excellent device stability is obtained after rapid thermal annealing (RTA) treatment in nitrogen atmosphere. The RCA transistor exhibits good electrical performance at very low temperature for an emitter area of 3 × 8 μm². The maximum toggle frequency of a 1:2 static divider is 1.2 GHz and 732 MHz at 300 K and 77 K, respectively     

轧机主传动万向联轴器辊端接头结构探讨

分析了衬板槽平面与叉头十字轴孔轴线的相对位置对辊端接头应力的影响 ,研究了轧辊扁头与衬板之间间隙所产生的冲击和应力集中 ,讨论了辊端接头中部过渡段结构对应力分布和制造质量的影响。提出辊端接头结构设计的优化方案     

减压渣油与FCC油浆共炭化的化学组成变化

考察了齐鲁石化胜利炼油厂催化油浆（FCC）和胜利减压渣油（VR）在490℃，0.8MPa下不同混合比的原料和不同反应时间的中间产物的HS、TS、PS、P及其1h中间产物的HS和TS的^1H-NMR。数据结果反映了体系的反应速度。掺入FCC油浆抑制了VR的反应活性，降低了体系的反应速度，增加了基质的溶解度；1h中间产物的组成结构更接近于原料及反应体系的反应性和基质的溶解度；1h中间产物的芳香度越高，取代基越少，侧链越短，基质对VR中的活性反应组分在炭化早期生成的高度缩合物质的溶解度越大。     

健康住宅正在走近我们

人类居住健康的问题越来越受到全世界居住者和舆论的关注.长期以来人类过于不当的城市建设行为,人口的过于集中,城市建筑的高层化倾向,过分的人造环境造成土地失水性严重、热岛现象衍生.城市作为人类居住生活的功能区,在很大程度上被削弱,居住条件恶化、环境受到污染.让城市功能朝着人居、健康的目标发展,包括生理和心理的、社会的和人文的、近期的和长期的多层次的健康,是我们今天的历史责任.     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.     

Preparation and photochromism of nanocomposite thin film based on polyoxometalate and polyethyleneglycol

A photochromic nanocomposite based on Keggin structure phosphomolybdic acid (PMoA) well dispersed in polyethyleneglycol (PEG) was fabricated. TEM image showed that PMoA nanoparticles with narrow size distribution were finely dispersed in polymer matrix. FT-IR results showed that the Keggin geometry of polyoxometalates was still preserved inside the composites and strong coulombic interaction was built between PMoA and polymer matrix. Under UV irradiation, the film was reduced photochemically to yield a blue species, which was in accordance with a charge-transfer mechanism.