(Nb,Ti)C的制备方法对(Nb,Ti)C-35Ni金属陶瓷的微观结构及性能的影响

用自蔓燃高温合成（SHS）技术及电弧熔融法制备的（Nb，Ti）C固溶体作基体，制备（Nb，Ti）C－35Ni金属陶瓷。结果表明用电弧熔融法制备的（Nb，Ti）C为基的试样具较优的室温力学性能（σ＝1630MPa，KIC＝18．0MPa），其陶瓷颗粒均匀分行粘结相之中并是包裹结构；而用SHS法制备的（Nb，Ti）C为基的试样其力学性能相对较差，其陶瓷颗粒无包裹结构．     

Ultraviolet chambers based on integrating spheres for use in artificial weathering

Laboratory ultraviolet (UV) chambers are widely used to obtain weathering data for a wide range of commercial polymer products including coatings, textiles, elastomers, plastics, and polymeric composites. Although numerous improvements have been made in the design of UV chambers over the last 80 years, the reproducibility of the exposure results from these chambers has remained elusive. This lack of reproducibility is attributed to systematic errors in their design, operation, and control which prevent direct comparisons of the performance of materials exposed in the same environment, comparisons of the performance of the same material exposed in different laboratories, and the comparison of field and laboratory results. This paper describes an innovative UV chamber design based on integrating sphere technology that greatly reduces the magnitude of these errors, as well as provides additional experimental capabilities. Presented at the 79th Annual Meeting of the Federation of Societies for Coatings Technology, on November 4–7, 2001, in Atlanta, GA. Building Materials Division. Gaithersburg, MD. Freeport, TX.     

On the mechanical behavior of aluminum alloys reinforced by long or short alumina fibers or SiC whiskers

This study was initiated to examine the dispersion of longitudinal and transverse waves in metal matrix composites in order to obtain the dynamic elastic modulus and to evaluate various models for predicting the composite's macroscopic elastic constants from the properties of its constituents. The materials chosen for this investigation were alumina continuous fibers on the one hand and alumina and SiC short fibers on the other hand, all embedded in an aluminum alloy matrix. In addition, some indications have been obtained experimentally for the acoustoelastic effect in the composite.     

Flame temperature, fuel structure, and fuel concentration effects on soot formation in inverse diffusion flames

Insights into soot formation processes are gained from chemical sampling and thermocouple probing of co-flowing inverse diffusion flames (IDFs), with the oxidizer in the center. The transition from near-to slightly sooting flames and the effects of flame temperature, fuel concentration, and fuel structure (using methane, ethene, propene and 1-butene) are investigated. The aromatic content of IDFS scales with the fuel's sooting tendency, and suggests that the formation of the aromatic ring is a controlling step in soot formation. In addition to the relatively well-established reactions involving C4 and C2 species, benzene may form directly from two C3 species for fuels that readily produce C3 species during pyrolysis and/or oxidative pyrolysis. The total concentration of growth species increases almost linearly with fuel concentration, but depends more weakly on flame temperature than would be expected if pure pyrolysis governed the intermediate hydrocarbon behavior.     

矿山抗采动农村楼房的试验研究

本文通过两栋不同加固方案的二层农村楼房抗采动现场试验结果的分析,对不同加固措施的作用机理、效果及其设置条件进行了研究探讨,并提出,在农村采动区兴建抗采动变形楼房,是解放村庄下压煤、节约耕地和降低加固费用的途径。     

微波等离子体化学气相沉积的 a-Si∶H 性能研究

本文着重对微波等离子体化学气相沉积法高速沉积的 a-Si∶H 膜的物理性能进行评价研究.测量了沉积膜的光电性能、暗电导激活能、光禁带宽度、光吸收特性、沉积膜中悬键态密度以及氢含量等,并讨论沉积条件对膜性能的影响.结果表明,在沉积速率高达30～90(?)/s 情况下,膜的光电导(光照强度10~5Lux)与暗电导比值可达10~3～10~5,暗电导率从10~(-3)到10~(-11)((?)cm)~(-1),其激活能在0.23～0.88eV 之间(0～200℃温度范围内),光禁带宽度为1.40～2.20eV,氢含量约为2～20%.     

分布系统中多米诺效应的分析与消除

分布系统中发生故障后,错误信息在进程间的传播,以及由此引起的系统恢复过程中的多米诺效应是分布系统容错恢复技术所面临的最重要与最困难的问题.目前各种研究工作偏重于具体的系统动态恢复技术.本文的研究重点在于首次揭示多米诺效应本身固有的数量特征及其与分布系统技术参数间的联系,给出多米诺效应动态消除技术,引入系统额外开销的下限,并针对动态技术的缺点,探讨多米诺效应的静态消除技术,为解决困难开辟新途径.     

Some aspects of deformation behavior

The deformation behavior of several single- and two-phase coarse microstructures has been examined using microhardness measurements. It has been found that the strength response of a coarse phase in isolation is distinctly different from its response when it exists in a two-phase system. The second phase alters the mechanical state of the first one andvice versa even in the plastically undeformed condition. This phenomenon is explained in terms of the existence of an appreciable amount of residual stresses in two-phase coarse microstructures. These stresses primarily arise due to the difference in thermal expansion coefficients of the phases. The in- fluence of elastic stress field on microhardness response is shown with a new type of experiment to support the proposed explanation. The present results question the existing expressions for deformation modeling of multiphase materials because of the uncertainties in the estimation of the average strength of the phases in a two-phase system.