~（131）Ⅰ—MIBG比活度对鼠心肌交感神经囊泡内外摄取的影响

研究了两种比活度的１３１Ⅰ－ＭＩＢＧ在正常及利血平抑制后在鼠体内的分布，结果表明：注射后４ｈ，正常鼠心肌对３．２２ＴＢｑ／ｇ的ＭＩＢＧ摄取为９．０８％ＩＤ／ｇ，明显高于对１８．５ＧＢｑ／ｇ的摄取（４．８７％ＩＤ／ｇ）。计算表明，比活度主要影响了鼠心肌交感神经囊泡内摄取，而与囊泡外摄取无关．当ＭＩＢＧ用于心肌显像时，高比活度的ＭＩＢＧ有利于诊断。     

Deformation and fracture of glass bead/ CTBN-rubber/epoxy composites

Carboxyl-terminated butadiene-acrylonitrile-rubber decreases modulus and yield stress of the studied epoxy but increases fracture toughness. The addition of glass bead compensates for the loss in modulus but has little effect on yield stress. However, it significantly contributes to the fracture toughness by providing additional mechanisms for toughening of both the unmodified and rubber-modified epoxy. For the toughened epoxies studied, fracture surfaces gave only limited information on fracture mechanisms since significant energy absorption also occurs in the material below the fracture surface. Suggestions for suitable material compositions for fiber composite matrices are given.     

Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

A robust adaptive pole‐placement controller without strictly positive real condition

This paper considers the adaptive pole‐placement control problem for system (1) with unmodelled dynamics η_n dominated by a small constant ε multiplied by a quantity independent of ε but tending to infinity as the past input, output, and noise grow. Using bounded external excitation and randomly varying truncation techniques, we give a design method of adaptive pole‐placement controller. It is shown that the closed‐loop system is globally stable, the estimation error for the parameter contained in the modelled part is of order ε, and the closed‐loop system under the adaptive pole‐placement control law is suboptimal in the sense of $$\mathop{\lim\sup}\limits_{{n\to\infty }}{1\over n}\mathop{\sum}\limits_{i=0}^n{\left({A^{*}(z)y_{n}‐L(z)C(z)w_{n}‐B(z)R(z)y_{n}^{*}}\right)^{2}{\leq}O({\varepsilon}^{2})+\gamma^{2}\mathop{\sum}\limits_{j=1}^q{b_{j}^{2}}}$$\nopagenumbers\end while the SPR condition used usually in other papers is replaced by a stability condition. Copyright © 2001 John Wiley & Sons, Ltd.     

首钢外购焦炭质量恶化后的高炉生产实践

针对焦炭质量劣化的状况，高炉操作以活跃炉缸为主，从上下部调剂入手，采取疏导煤气、控制合理的实际风速和鼓风动能、缓解焦炭在高温区的粉化等措施，有效地改善了高炉的顺行状况，并逐步恢复高炉指标。     

Preparation of flexible polyhedral particles via concentrated emulsion templating polymerization

This paper presents recent efforts on the preparation of flexible polyhedral particles via concentrated emulsion templating polymerization in which the hydrophilic monomer (acrylamide) and hydrophobic monomer (butyl acrylate) are polymerized simultaneously in the continuous and dispersed phase, respectively. Such templating polymerization has been enhanced in our systems owing to the introduction of acrylamide monomer and their higher polymerization rate in continuous phase as compared with butyl acrylate in dispersed phase. Diffusion between the different phases was also inhibited. Furthermore, the stability of the concentrated emulsion and the molecular weight of the produced poly(butyl acrylate) were found to be significantly affected by the amount of redox initiator. The morphology of the particles could be controlled by varying the volume fraction of the dispersed phase and the polyhedral particles were achieved at higher volume fraction. Copyright © 2005 Society of Chemical Industry     

Ring‐opening polymerization of D,L‐lactide by rare earth 2,6‐dimethylaryloxide

Ring‐opening polymerization of D,L ‐lactide (LA) has been successfully carried out by using rare earth 2,6‐dimethylaryloxide (Ln(ODMP)₃) as single component catalyst or initiator for the first time. The effects of different rare earth elements, solvents, monomers and catalyst concentration as well as polymerization temperature and time on the polymerization were investigated. The results show that La(ODMP)₃ exhibits higher activity to prepare poly(D,L ‐lactide) (PLA) with a viscosity molecular weight of 4.5 × 10⁴ g mol^?1 and the conversion of 97 % at 100 °C in 45 min. The catalytic activity of Ln(ODMP)₃ has following sequence: La > Nd > Sm > Gd > Er > Y. A kinetic study has indicated that the polymerization is first order with respect to both monomer and catalyst concentration. The apparent activation energy of the polymerization of LA with La(ODMP)₃ is 69.6 kJ mol^?1. The analyses of polymer ends indicate that the LA polymerization proceeds according to ‘coordination–insertion’ mechanism with selective cleavage of the acyl–oxygen bond of the monomer. Copyright © 2004 Society of Chemical Industry