THE EXTRACTION OF NEPTUNIUM(V) BY METHYLTRIOCTYLAMMONIUM CHLORIDE AND 1-PHENYL-3-METHYL-4-BENZOYL-5-PYRAZOLONE

The synergistic effect of methyltrioctylammonium chloride (QCI) on the extraction of Np(V) by 1-phenyl-3-methyl-4-benzoyl-pyrazolone(HP) in benzene is studied over the pH range 2-6. This system extracts Np(V) better than any previously reported. The interaction of the extractants and monomer-dimer equilibria affect the distribution behavior of Np(V) in a complicated manner. Analysis of the results suggests that NpO₂ ⁺ (M⁺) is extracted as mixed dimers, (QMP₂QCl)_o and (QMP₂QP)_o.     

Deterioration of diacylglycerol‐ and triacylglycerol‐rich oils during frying of potatoes

The stabilities of a commercial diacylglycerol‐rich oil (DAG) and a salad oil (TAG) that had been prepared from a mixture of rapeseed and soybean oils were compared while frying potatoes at 180 °C for 3 h. The representative chemical and physical characteristics of the oils were assessed before and after frying, together with the amount of volatile aldehydes in the exhaust of frying. Among the deterioration indications, the carbonyl value, polymer content, and residual polyunsaturated fatty acid content were similar and not significantly different between the TAG and DAG. On the other hand, the characteristics relating to free fatty acids, i.e. the acid value and emission of chemiluminescence at 100 °C, were greater and the smoke and flash points were lower in the DAG than in the TAG. An irritating odor was generated from the DAG after 1 h of frying and got stronger as frying continued. These results suggested that DAG more easily forms free fatty acids under frying conditions than TAG.     

Dependence of property, cathode characteristics, thermodynamic stability, and average and local structures on heat-treatment condition for LiNi0.5Mn0.5O2 as a cathode active material for Li-ion battery

LiNi_0.5Mn_0.5O₂ was heat-treated under high oxygen-pressure and Ar-reducing conditions, and then the cathode properties, thermodynamic stability and average and local structures were investigated. From X-ray diffraction and ICP measurements, it was found that the pristine LiNi_0.5Mn_0.5O₂ had a single phase of the layered rock-salt structure although the Ni content was slightly rich compared with the nominal one. These characteristics were kept even after the heat-treatments. Charge–discharge cycle tests clarified that the cycle performance of LiNi_0.5Mn_0.5O₂ was improved by both the reducing and oxidizing treatments. From neutron diffraction and X-ray absorption fine structure measurements, the local distortion around the transition metal, especially Ni, was supposed to be one of the important factors to determine the cathode properties. It was also found that the sample with higher thermodynamic stability exhibited better capacity retention in the discharge–charge cycle tests.     

Retardation of volatile aldehyde formation in the exhaust of frying oil by heating under low oxygen atmospheres

Volatile aldehydes were generated in the exhaust of high-oleic safflower oil during heating at 180°C by spraying water into atmospheres with four levels of oxygen concentrations (2, 4, 10, and 20%). These aldehydes were quantitatively analyzed by HPLC after the conversion to 2,4-dinitrophenyl hydrazones. Ten alkanals (C₂ through C₁₀), eight 2-alkenals (C₃ through C₁₀) and three 2,4-alkadienals (C₇, C₉, and C₁₀) were found. These aldehyde levels were found to be positively correlated with both the heating time and the atmospheric oxygen concentration. The total amounts of aldehydes were the lowest in the oil heated in an atmosphere with 2% O₂, and corresponded to 1/10 of those in the atmosphere with 20% O₂. Acrolein was not found in oils heated in the atmosphere with 2% oxygen. These results suggest that frying in atmospheres with low oxygen levels can effectively decrease the generation of volatile aldehydes in the exhaust.     

Characterization of a Silk‐Resinified Compact Fabricated Using a Pulse‐Energizing Sintering Device

Pulse electric current sintering is used to prepare a compact from resinificated hydrous silk powder. Compacts with no remnant silk powders are formed with 20 wt% added water, 20–40 MPa molding pressure, and >353 K molding temperature. The latter two are much lower than those used for conventional hot pressing. No dependence on molding pressure and temperature are found in XRD or FT‐IR analysis, except for a compact molded at 473 K, for which silk fibroin decomposition is confirmed by DSC, EGA‐MS, and molecular weight measurements. The compact's three‐point bending strength depends on the molding temperature, except for the temperature at which silk fibroin decomposes. The maximum three‐point bending strength resembles that of general‐purpose epoxy resin and is much higher than that of PLA.

     

Effect of Phosphorus Ions on the Proton Conductivity in the Sol–Gel-Derived Porous Glasses

The effect of phosphorus ions on the proton conductivity was examined for the sol–gel-derived glasses. The porous glasses were prepared through hydrolysis of PO(OCH₃)₃ and Si(OC₂H₅)₄, in which the phosphorus ions consisted of the POH bonds and were dissolved into the silica matrix without any P-O-Si bond. The electrical conductivity increased in a humid atmosphere and reached ∼30 mS/cm at 50°C under 70% RH. High conductivity is achieved by both the POH bonds and the molecular water bonded to the POH bonds. The conductivity increased with a change in humidity from 40% to 80% RH. The phosphorus ions were selectively dissolved in water, resulting in a lower conductivity.     

Removal of nitrogen oxides from air by chemicals-impregnated carbons

Fixation of nitrogen oxides (NO_x) in air onto granular activated carbon impregnated with chemicals was attempted to improve removal efficiency of NO_x by activated carbon adsorption. Nitric oxide (NO) and nitrogen dioxide (NO₂), were tried to remove by a flow test. Fixed-bed adsorption breakthrough curves were obtained when some kinds of carbon were used. The amount adsorbed of NO₂ changed with the amount and kinds of metallic salts impregnated. Chemicals-impregnated carbons were prepared from a commercial activated carbon. Among obtained carbons, the one which showed the highest selectivity for NO_x was chosen, and its performance with the change in humidity was determined. Removal mechanism of NO₂ was estimated, and the carbon impregnated with potassium hydroxide was found to be superior to any other carbon tested. The amount of the adsorbed NO and that produced by the reduction of NO₂ were determined from the breakthrough curves.     

Dielectric Depression and Dispersion in Electrophoretically Fabricated BaTiO3 Ceramic Films

Dielectric depression and dispersion were observed in BaTiO3 ceramic films fabricated by electrophoretic deposition followed by sintering. The dielectric constants were depressed down to 6800–4600 around the Curie point ( T _C ). The dielectric dispersion occurred above T _C . These dielectric properties are attributable to a surface layer formed during sintering. XRD analysis indicated that the surface layer was a hexagonal-like BaTiO₃ phase. A mixed solvent of acetylacetone and alcohol employed in the present work may have been responsible for the formation of the surface layer.