Investigation of hydrogen plasma treatment for reducing defects in silicon quantum dot superlattice structure with amorphous silicon carbide matrix

We investigate the effects of hydrogen plasma treatment (HPT) on the properties of silicon quantum dot superlattice films. Hydrogen introduced in the films efficiently passivates silicon and carbon dangling bonds at a treatment temperature of approximately 400°C. The total dangling bond density decreases from 1.1 × 10¹⁹ cm^-3 to 3.7 × 10¹⁷ cm^-3, which is comparable to the defect density of typical hydrogenated amorphous silicon carbide films. A damaged layer is found to form on the surface by HPT; this layer can be easily removed by reactive ion etching.     

Moving pick‐up‐type contactless power transfer systems and their efficiency using series and parallel resonant capacitors

The equivalent circuit, the efficiency, and the important characteristics of moving pick‐up type contactless power transfer systems are described. If the primary series capacitor and the secondary parallel capacitors are chosen correctly and the winding resistances are ignored, the equivalent circuit of the transformer with these capacitors becomes the same as an ideal transformer at the resonant frequency. This simple approximation helps to understand the phenomena occurring with load changes. Because the circuit analysis becomes simple, the approximate value of the power transfer efficiency can be derived. This paper describes the determination of the capacitor values, the derivation of the equivalent circuit and the efficiency, and test results. © 2010 Wiley Periodicals, Inc. Electr Eng Jpn, 172(2): 47–54, 2010; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20970     

Crystallization in rapid quenching of La0.33NbO3 melt

Transparent La_0.33NbO₃ flakes were fabricated by a rapid quenching technique. The quenched La_0.33NbO₃ phase takes a simple cubic perovskite structure and cation vacancies are randomly distributed on the A sites. The cubic La_0.33NbO₃ phase is a new modification which is different from the well-known orthorhombic phase with ordered A-site vacancies. Transparent flakes were found to show the predominant orientation of (110) and (220) planes.     

Near-net-shape forming of Al-Al3Ni functionally graded material over eutectic melting temperature

A possibility to make near-net-shape functionally graded material (FGM) products has been examined. The FGM billets having a graded volume fraction of Al₃Ni in thickness direction were machined from an Al-Al₃Ni FGM thick-walled tube manufactured by a vacuum centrifugal method. Billets, which were set in the container for the backward extruding, were heated to 650 °C to 680 °C, at which temperature the FGM becomes a mixture of molten aluminum eutectic and solid intermetallics. Then, billets were extruded successfully to FGM cups by a semisolid forming, except at 650 °C. Residual bulky Al₃Ni particles are found at higher temperature. Thus, an optimum operation temperature is found to be around 660 °C, because bulky Al₃Ni particles transform to fine spheroidal or fibrous shape after the forming. The volume fraction of intermetallics at the bottom region of the cup was condensed more than 60 vol pct in a proper billet setting.     

Dynamic Characteristics Analysis of Two‐DOF Oscillatory Actuator and Experimental Verification of Prototype

Recently, linear oscillatory actuators have been used in a wide range of applications. In particular, small linear oscillatory actuators are expected to be used in haptic devices by being extended to provide multi‐degree‐of‐freedom motion with arbitrary acceleration. In this paper, we propose a compact two‐DOF oscillatory actuator that can move in various directions on a plane. The static and dynamic characteristics of the actuator are determined by the 3D finite element method. The effectiveness of this method is shown through a comparison of the measured results with the experimental results from a prototype. © 2013 Wiley Periodicals, Inc. Electr Eng Jpn, 186(1): 58–65, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22312     

Bloom Formation on Poorly-Tempered Chocolate and Effects of Seed Addition

Bloom on chocolate with different levels of cocoa butter seed addition was investigated. When insufficient cocoa butter seed crystals were added to give proper temper, the chocolate developed bloom as dark brown spheres in lighter color areas, similar to that seen in bloom on untempered chocolate. These dark colored spheres overlapped and the lighter color areas disappeared with increasing seed amount added. The relationship between seed amount and lighter color area (bloom), as quantified by image analysis, showed that over 270 ppm seeds (fat basis) were needed to accomplish good tempering. The cocoa butter crystallization behavior with various amounts of seed was observed by light microscopy. Too few seeds caused sparse β crystallization and massive β′ crystallization, which explains the appearance of poorly tempered chocolate bloom. As seed amount increased, β crystallization of cocoa butter took less time to reach the upper level of solid fat content and the size became smaller. In addition, DSC analysis was carried out to study crystallization and melting behavior of cocoa butter with different seed amounts. Higher levels of added seeds resulted in greater amounts of β crystal formation and the crystallization temperature increased, which meant crystallization occurred earlier. These results showed that the mechanism of bloom formation on poorly tempered chocolate (insufficient seeds) is due to sufficient time and space for phase (particles and fat) separation as the stable polymorphs grow.     

Two acyl-CoA dehydrogenases of Acinetobacter sp. strain M-1 that uses very long-chain n-alkanes

Two genes encoding acyl-CoA dehydrogenases, acdA and acdB, arranged in tandem, were found in the chromosomal DNA of Acinetobacter sp. strain M-1. AcdA was purified from the parental strain and AcdB was purified from an Escherichia coli strain expressing the cloned gene. The substrate specificities of the two enzymes suggest that AcdA is a medium-chain acyl-CoA dehydrogenase and that AcdB is a long-chain acyl-CoA dehydrogenase. Characterization of n-alkane metabolism in Acinetobacter sp. strain M-1 has revealed parallel pathways as well as enzymes with overlapping specificities in a single pathway. The two acyl-CoA dehydrogenases described here provide another example of the physiological complexity underlying n-alkane utilization.     

An optimal loading principle of burnable poisons for an OTTO refueling scheme in pebble bed HTGR cores

An optimal loading principle of burnable poisons (BPs) is proposed to eliminate the problem of an excessively high power peaking factor in once-through-then-out (OTTO) pebble bed HTGR cores. The effectiveness of the principle is confirmed through neutronic and thermal hydraulic calculations for an HTGR core with thermal power of 600 MWt. Spherical BP particles are distributed uniformly together with TRISO-coated fuel particle inside the free fuel zones of fuel pebbles to maintain constant k_∞ during burnup. The applicability of BP materials, such as B₄C, Gd₂O₃, Sm₂O₃, Eu₂O₃, Er₂O₃, CdO, and HfO₂, is investigated. Because complete BP depletion at the target burnup is required to avoid reactivity loss and extra enrichment, the four BP materials considered as applicable candidates are B₄C, Gd₂O₃, Er₂O₃, and CdO. The complete BP depletion is demonstrated by a burning fraction at the target burnup. The power density is excessively high at the core top and the power peaking factor is 4.44 when no BP is added to the fuel pebbles. Optimal BP loading reduces the power peaking factor from 4.44 to about 1.7. Because of the power peaking factor reduction, the maximum fuel temperatures are lower than the maximum permissible values of 1250 °C for normal operation and 1600 °C during a depressurization accident.     

Silicon quantum dot superlattice solar cell structure including silicon nanocrystals in a photogeneration layer

The solar cell structure of n-type poly-silicon/5-nm-diameter silicon nanocrystals embedded in an amorphous silicon oxycarbide matrix (30 layers)/p-type hydrogenated amorphous silicon/Al electrode was fabricated on a quartz substrate. An open-circuit voltage and a fill factor of 518 mV and 0.51 in the solar cell were obtained, respectively. The absorption edge of the solar cell was 1.49 eV, which corresponds to the optical bandgap of the silicon nanocrystal materials, suggesting that it is possible to fabricate the solar cells with silicon nanocrystal materials, whose bandgaps are wider than that of crystalline silicon.

PACS

85.35.Be; 84.60.Jt; 78.67.Bf