Radiation safety management of residual long-lived radioactivity distributed in an inner concrete wall of a medical cyclotron room

The depth distribution of residual long-lived radioactivity in the inner concrete wall of a medical cyclotron room was measured by assaying concrete cores. Seven long-lived radioactive nuclides ((46)Sc, (60)Co, (65)Zn, (134)Cs, (152)Eu, (22)Na and (54)Mn) were identified by gamma-ray spectrometry of the concrete samples. It was confirmed that the gamma-ray-emitting radionuclides induced by thermal neutrons through the (n, γ) reaction are dominant, and that the activity induced by thermal neutrons is greater at a depth of 10-30 cm, rather than at the surface of the concrete, and decreased exponentially beyond a depth of ~40 cm. Although the specific activity at the surface was greater than the clearance level for radioactive waste indicated in IAEA RS-G-1.7, the mean specific activities in the walls and floor were less than the clearance level.     

Radiocarbon (14C) diurnal variations in fine particles at sites downwind from Tokyo, Japan in summer

The radiocarbon ((14)C) of total carbon (TC) in atmospheric fine particles was measured at 6 h or 12 h intervals at two sites, 50 and 100 km downwind from Tokyo, Japan (Kisai and Maebashi) in summer 2007. The percent modern carbon (pMC) showed clear diurnal variations with minimums in the daytime. The mean pMC values at Maebashi were 28 ± 7 in the daytime and 45 ± 16 at night (37 ± 15 for the overall period). Those at Kisai were 26 ± 9 in the daytime and 44 ± 8 at night (37 ± 12 for the overall period). This data indicates that fossil sources were major contributors to the daytime TC, while fossil and modern sources had comparable contributions to nighttime TC in the suburban areas. At both sites, the concentration of fossil carbon as well as O(3) and the estimated secondary organic carbon increased in the daytime. These results suggest that fossil sources around Tokyo contributed significantly to the high daytime concentration of secondary organic aerosols (SOA) at the two suburban sites. A comparison of pMC and the ratio of elemental carbon/TC from our particulate samples with those from three end-member sources corroborates the dominant role of fossil SOA in the daytime.     

LiNi₁/₃Co₁/₃Mn₁/₃O₂-graphene composite as a promising cathode for lithium-ion batteries

The use of graphene as a conductive additive to enhance the discharge capacity and rate capability of LiNi(1/3)Co(1/3)Mn(1/3)O(2) electrode material has been demonstrated. LiNi(1/3)Co(1/3)Mn(1/3)O(2) and its composite with graphene (90:10 wt %) were prepared by microemulsion and ball-milling techniques, respectively. The structural and morphological features of the prepared materials were investigated with powder X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy. Characterization techniques depict single-phase LiNi(1/3)Co(1/3)Mn(1/3)O(2) with particle sizes in the range of 220-280 nm. Electrochemical studies on LiNi(1/3)Co(1/3)Mn(1/3)O(2) and LiNi(1/3)Co(1/3)Mn(1/3)O(2)-graphene were conducted using cyclic voltammetry, galvanostatic charge-discharge, and electrochemical impedance spectroscopy methods by constructing a lithium half-cell. Cyclic voltammograms show the well-defined redox peaks corresponding to Ni(2+)/Ni(4+). Charge-discharge tests were performed at different C rates: 0.05, 1, and 5 between 2.5 and 4.4 V. The results indicate the better electrochemical performance of the LiNi(1/3)Co(1/3)Mn(1/3)O(2)-graphene composite in terms of high discharge capacity (188 mAh/g), good rate capability, and good cycling performance compared to LiNi(1/3)Mn(1/3)Co(1/3)O(2). The improved electrochemical performance of the LiNi(1/3)Co(1/3)Mn(1/3)O(2)-graphene composite is attributed to a decrease in the charge-transfer resistance.     

Involvement of sensory neurons in bone defect repair in rats

We investigated bone repair in sensory-denervated rats, compared with controls, to elucidate the involvement of sensory neurons. Nine-week-old male Wistar rats received subcutaneous injections of capsaicin to denervate sensory neurons. Rats treated with the same amount of vehicle served as controls. A standardized bone defect was created on the parietal bone. We measured the amount of repaired bone with quantitative radiographic analysis and the mRNA expressions of osteocalcin and cathepsin K with real-time polymerase chain reaction (PCR). Quantitative radiographic analysis showed that the standard deviations and coefficients of variation for the amount of repaired bone were much higher in the capsaicin-treated group than in the control group at any time point, which means that larger individual differences in the amount of repaired bone were found in capsaicin-treated rats than controls. Furthermore, radiographs showed radiolucency in pre-existing bone surrounding the standardized defect only in the capsaicin-treated group, and histological observation demonstrated some multinuclear cells corresponding to the radiolucent area. Real-time PCR indicated that there was no significant difference in the mRNA expression levels of osteocalcin and cathepsin K between the control group and the capsaicin-treated group. These results suggest that capsaicin-induced sensory denervation affects the bone defect repair.     

A novel approach to a fine particle coating using porous spherical silica as core particles

The applicability of porous spherical silica (PSS) was evaluated as core particles for pharmaceutical products by comparing it with commercial core particles such as mannitol (NP-108), sucrose and microcrystalline cellulose spheres. We investigated the physical properties of core particles, such as particle size distribution, flow properties, crushing strength, plastic limit, drying rate, hygroscopic property and aggregation degree. It was found that PSS was a core particle of small particle size, low friability, high water adsorption capacity, rapid drying rate and lower occurrence of particle aggregation, although wettability is a factor to be carefully considered. The aggregation and taste-masking ability using PSS and NP-108 as core particles were evaluated at a fluidized-bed coating process. The functional coating under the excess spray rate shows different aggregation trends and dissolution profiles between PSS and NP-108; thereby, exhibiting the formation of uniform coating under the excess spray rate in the case of PSS. This expands the range of the acceptable spray feed rates to coat fine particles, and indicates the possibility of decreasing the coating time. The results obtained in this study suggested that the core particle, which has a property like that of PSS, was useful in overcoming such disadvantages as large particle size, which feels gritty in oral cavity; particle aggregation; and the long coating time of the particle coating process. These results will enable the practical fine particle coating method by increasing the range of optimum coating conditions and decreasing the coating time in fluidized bed technology.     

A real-time inspection system using a terahertz technique to detect microleak defects in the seal of flexible plastic packages

A method to detect production faults in flexible plastic packages with the use of terahertz radiation is presented. Relying on the large difference between the absorption coefficients of plastic and water (for water-filled channel defects) and on the refraction index difference between plastic and air (for air-filled channel defects), our technique consists of focusing and scanning a terahertz beam on the sealed area of the package, followed by detection of the transmitted signal. Compared with previous methods, such as visual and ultrasound inspection, our technique can be applied to optically opaque packages and does not require immersion in a matching liquid. We tested our system on defects that we fabricated as water-filled and air-filled channels imbedded in polyethylene films, with diameters in the range of 10 to 100 microm. The detection limit (the minimum size of a detectable defect) depends on the conveying speed; this relationship was determined and analyzed. The results show that our system has the potential for application in an actual production line for real-time inspection.     

Integrating Oxygen and 3D Cell Culture System: A Simple Tool to Elucidate the Cell Fate Decision of hiPSCs

Oxygen, as an external environmental factor, plays a role in the early differentiation of human stem cells, such as induced pluripotent stem cells (hiPSCs). However, the effect of oxygen concentration on the early-stage differentiation of hiPSC is not fully understood, especially in 3D aggregate cultures. In this study, we cultivated the 3D aggregation of hiPSCs on oxygen-permeable microwells under different oxygen concentrations ranging from 2.5 to 20% and found that the aggregates became larger, corresponding to the increase in oxygen level. In a low oxygen environment, the glycolytic pathway was more profound, and the differentiation markers of the three germ layers were upregulated, suggesting that the oxygen concentration can function as a regulator of differentiation during the early stage of development. In conclusion, culturing stem cells on oxygen-permeable microwells may serve as a platform to investigate the effect of oxygen concentration on diverse cell fate decisions during development.     

Design and calibration of curved and see-through integral imaging 3D display

Virtual Reality - Heads-up displays that are ‘see-through’ and ‘curved’ and capable of displaying 3D contents are considered crucial for augmented reality-based navigation...